SYNCRO_V_MANUAL_EN_R1_web - Digimerge

More documents

Recommendations

Info

Playback7. Click to begin playback. Click inside the Seek Bar to select a different playback time.Click inside theseek bar to changeplayback timeClick to startplaybackRecord Playback overview1 3425671. Device List: Select Devices to search.2. Search Options: Select Local Playback to playback from NAS or hard drive location.Select Remote Playback to playback from camera microSD/SD card. Configure StartTime and End Time for search. Configure paths for Local Playback.3. Display Area4. Seek Bar: Click to change playback time.26
Playback5. Playback Controls :• : Click to begin playback.• : Click to pause playback.• : Click to stop playback.• : Click to go back frame-by-frame.• : Click to go forward frame-by-frame.• : Click to playback at 1/2 speed.• : Click to playback at 1/4 speed.• : Click to playback at 1/8 speed.• : Click to playback at 1/16 speed.• : Click to rewind.• : Click to fast forward 2x.• : Click to fast forward 4x.• : Click to fast forward 8x.• : Click to fast forward 16x.6. Playback Timeline and Timeline Zoom Controls: Use Timeline Zoom controls tochange the scope of the Playback Timeline.• : Click then click inside the Playback Timeline to zoom in on the selected time.• : Click then click inside the Playback Timeline to zoom out on the selected time.• : Click to return to the default zoom level.• : Click to change the timeline interval to 10 seconds. For example, if the first timeshown on the timeline is 8:55:10, the next time shown will be 8:55:20.• : Click the change the timeline interval to 30 seconds.• :Click to change the timeline interval to 1 minute.• : Click to change the timeline interval to 5 minutes.• : Click to change the timeline interval to 10 minutes.7. Device Status: Left side shows the IP address of the selected device. Bar shows timeswith saved video (continuous recording in green; alarm recording in red).27
Page 1: Syncro-VClient Software for SyncroI
Page 7 and 8: Getting StartedGETTING STARTEDSyste
Page 9 and 10: Getting Started5. Under User Name a
Page 11 and 12: Getting Started8. Close all windows
Page 13 and 14: Using the System Interface8. Multi-
Page 15 and 16: Using the System InterfaceDisplay w
Page 17 and 18: Using the System InterfaceTo create
Page 19 and 20: Using the System InterfaceCycle Lis
Page 21 and 22: Setting up Recording5. Click Apply
Page 23 and 24: Setting up Recording4. Under Time Z
Page 25 and 26: Setting up Recording7. Check Use Al
Page 27 and 28: Setting up Recording3. Check the ca
Page 29 and 30: Setting up Recording4. Under Motion
Page 31: PlaybackPLAYBACKYou can playback re
Page 35 and 36: Playback2. Click the - button.Click
Page 37 and 38: Playback2. Click Query. The results
Page 39 and 40: BackupBackup menuThe Backup Menu al
Page 41 and 42: Alarm ManagerALARM MANAGERThe Alarm
Page 43 and 44: Device Manager (configuring cameras
Page 71 and 72: System ManagerSYSTEM MANAGERThe Sys
Page 73 and 74: System Manager• Image Format Auto
Page 75 and 76: System ManagerGroupAdd, modify, or
Page 77 and 78: System Manager• To change the use
Page 79 and 80: System ManagerTo delete user accoun
Page 81 and 82: Configuring Camera Sensor SettingsC
Page 83 and 84:
Configuring Camera Sensor Settings
Page 85 and 86:
Configuring Camera Sensor SettingsA
Page 88:
Syncro-VEnglish Version 1.0www.digi
show all

SYNCRO_V_MANUAL_EN_R1_web - Digimerge

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?