configuration and options guide - IBM Quicklinks

Refer to the Important Notices section for important noticesFAStT EXP700 17401RU 3 23 91 245/350 2/2 2 2FC Switch 8-port 3534F08 1 17 17 -/50 1/1 1FC Switch 16-port 2109F16 1 25 28 -/200 1/2 1Tape Components:NetBAY 1U xSeries Tape Enclosure 45591UX 1 20 16 - 1/1 1NetBAY Tape Enclosure 0034B0X 4 18 39 320/457 1/1 1Full-High SCSI Tape Enclosure 3503B1X 3 11 8 - 1/1 13607 Series SDLTpro TapeAutoloader360716X 2 29.7 66 60/80 1/1 13607 Series LTO Tape Autoloader 360726X 2 29.7 66 60/80 1/1 1SDLT/LTO Modular Tape Library 4560SLX 5 31 70 300/430 1/1 1 11. Refer to Appendix eServer BladeCenter Power Upgrade Guidelines for important information that will help determine when a BladeCenterpower module upgrade is necessary.2. 1U = 1.75in (44.45mm).3. Includes three N+1 redundant power supplies. Uses only two power cords.4. Weight equals maximum ship configuration.5. Optional rack power cords: P/N 94G6667 - 14ft NEMA 5-15P; P/N 94G7448 - 14ft IEC 320-C14.6. Rack installation requires appropriate tower-to-rack conversion kit.7. Additional power cords are not required. This power supply option shares use of line cords provided with the base system. Should be orderedin pairs to maintain redundancy.8. To provide adequate cooling, blank filler panel kit (P/N 94G6670) should be placed on the front of any unused rack space. If non-IBM racks areto be used, assure that both front and rear doors offer a minimum of 48% open area uniformly distributed and in line with installed servers. Aclearance of 51 to 64mm (2 to 2.5in) must be maintained between the front of the door and the system unit’s front bezel. The rear door must maintainthe same or greater clearance. Nonrack or NetBAY3 installations are not supported.9. If installed in older IBM racks, the server should not be installed behind a glass door that blocks air flow. Remove the glass door or replace withan optional perforated door. To order a rack extension kit for withdrawn IBM racks, visit the Options Continuation Program Website atwww.pc.ibm.com/ww/ocp.10. Internal power supply logic limits low voltage (100-127VAC) to 550w per power supply. Thus, configurations requiring more power are notredundant for low voltage installations, e.g., configurations with more than two processors.Power Supply OptionsStandard Power CordsPower SupplyPart NumberUsable with6ft NEMA 5-15P69523019ft NEMA 5-15P69523009ft IEC 320-C1436L88869ft IEC C13/C2074P44308.2ft IEC C19/C2000N770114ft IEC 320-C19/C1412J59958.2ft IEC 320-C19NEMA 5-15P12J5112126w 18P3576 2109-F16 1950w 73P9709 x365 1 1350w 59P4057 x345 1514w 74P4965 x345 1 1370w 31P6108 RXE-100 1 1370w 31P6133 x255 1560w 02R1874 x235 22660w 02R2015 x235 2 21200w to 1400wUpgrade Kit90P0197 BladeCenter 341800w 13N0570 BladeCenter 3 21. Additional power cords are not required. This power supply option shares use of line cords provided with the base system.Should be ordered in pairs to maintain redundancy.2. Option includes two hot-swap power supplies and a power backplane. 02R1874 is compatible only with 533MHz FSB.3. Refer to Appendix eServer BladeCenter Power Upgrade Guidelines for important information that will help determinewhen a BladeCenter power module upgrade is necessary.Chapter 41. Rack Cabinets and Options 287