ISU AT Command Reference

More documents

Recommendations

Info

ISU AT Command ReferencePhase III AT Commands7.2.1 Direct Dial From Phonebook (Revised)The ISU and SIM contain phonebooks which have a phone number and an alphanumeric field for eachphonebook entry location. The use of V.25ter dialing command ensures that direct dialing from phonememory and SIM phonebook is possible through ordinary communications software which just gives thephone number field to be filled and then use the D command to originate the call. Available memories maybe queried with Select Phonebook Storage test command +CPBS=?, and location range for example withRead Phonebook Entries test command +CPBR=?.Execute commands:D>[;]Originate call to phone number which corresponding alphanumeric field is (if possible, all availablememories should be searched for the correct entry). is of string type value and should enclosed by ““(e.g., “John”).D> mem[;]Originate call to phone number in memory mem entry location (available memories may be queriedwith Select Phonebook Storage test command +CPBS=?).mem can be one of the following:FD SIM fixed dialing phonebookLD Last ten calls dialed phonebookME Phone memoryMT combined phone and SIM phonebook locationsSM SIM phonebookD>[;]Originate call to phone number in entry location (the command Select Phonebook Memory Storage+CPBS setting determines which phonebook storage is used).7.3 Hn - Hangup (Revised)Control the hook switch. This command is used to clear a data call connection. It is also used to clear avoice call connection when the ISU has originated the voice call with the ATD dial command or terminatedthe voice call with the ATA or ATS0=n answer command.0 Place the ISU on hook.7.4 S0=n - Auto-Answer (Revised)Auto-answer. This causes the ISU to auto-answer the incoming data or voice call.0 Disable auto-answer.n>0 Enable auto-answer after n ringsVersion 2.6March 30, 2006 48
ISU AT Command ReferencePhase III AT Commands7.5 Xn - Extended Result Codes (Revised)Select the response set to be used by the ISU when informing the DTE of the results of a command or dataor voice call.0 OK, CONNECT, RING, NO CARRIER, NO ANSWER and ERROR.CONNECT response is used to inform of a data call connection; OK response is used toinform of a voice call connection.1 As X0 plus CONNECT x, where x is the DTE speed.CONNECT x response is used for data calls only.2 As X1 plus NO DIALTONE.3 As X2 plus BUSY.4 As X3 plus CARRIER x, PROTOCOL: and COMPRESSION:, where x is the line speed(default).CARRIER x, PROTOCOL:, and COMPRESSION: responses are used for data callsonly.Note that the Wn command limits which connection related responses will be reported.7.6 &Dn - DTR Option (Revised)Set the ISU reaction to DTR signal.0 DTR is ignored in all modes. A DTR signal input is not needed when set to &D0.For all other &Dn settings, the following applies.DTR must be ON during on-hook command mode. If DTR transitions from ON to OFF during on-hookcommand mode, operation will be locked after approximately 10 seconds. On-hook command modeoperation will resume when DTR is restored ON.DTR must be ON at call connectionDTR must be ON during both in-call command mode and in-call data mode. Reaction to DTR ON to OFFtransitions during in-call command mode and in-call data mode is determined by the &Dn setting as shownbelow. Note that the +CVHU command can be set to override these specified reactions.1 If DTR transitions from ON to OFF during in-call command mode, and DTR is restored ONwithin approximately 10 seconds, the call will remain up. If DTR is not restored ON withinapproximately 10 seconds, the call will drop to on-hook command mode.If DTR transitions from ON to OFF during in-call data mode, the mode will change to in-callcommand mode. If DTR is restored ON within approximately 10 seconds, the call willremain up. If DTR is not restored ON within approximately 10 seconds, the call will drop toon-hook command mode.2 If DTR transitions from ON to OFF during either in-call command mode or in-call data mode,the call will drop to on-hook command mode (default).3 If DTR transitions from ON to OFF during either in-call command mode or in-call data mode,the call will drop to on-hook command mode and the ISU will reset to AT command profile 0.Version 2.6March 30, 2006 49
Page 1 and 2:
Version 2.6ISU AT Command Reference
Page 3 and 4:
ISU AT Command ReferenceRevision Hi
Page 5 and 6: ISU AT Command ReferenceTable of Co
Page 7 and 8: ISU AT Command ReferenceTable of Co
Page 9 and 10: ISU AT Command ReferenceIntroductio
Page 11 and 12: ISU AT Command ReferenceIntroductio
Page 13 and 14: ISU AT Command ReferenceModem Overv
Page 15 and 16: ISU AT Command ReferenceCommand Ove
Page 17 and 18: ISU AT Command ReferenceCommand Ove
Page 19 and 20: ISU AT Command ReferencePhased Impl
Page 21 and 22: ISU AT Command ReferencePhased Impl
Page 23: ISU AT Command ReferencePhase I AT
Page 26 and 27: ISU AT Command ReferencePhase I AT
Page 38: ISU AT Command ReferencePhase I AT
Page 42 and 43: ISU AT Command ReferencePhase II AT
Page 58 and 59: ISU AT Command ReferencePhase III A
Page 66 and 67: ISU AT Command ReferencePhase IV AT
Page 76 and 77: ISU AT Command ReferencePhase V AT
Page 78 and 79: ISU AT Command ReferencePhase VI AT
Page 90 and 91: ISU AT Command ReferenceS-Register
Page 96 and 97: ISU AT Command ReferenceSummary of
Page 98 and 99: ISU AT Command ReferenceInformative
show all

ISU AT Command Reference

Create successful ePaper yourself

Delete template?

Save as template?