ISU AT Command Reference

More documents

Recommendations

Info

ISU AT Command ReferencePhase V AT Commands9 Phase V AT Commands9.1 +CAR - Audio Output Control on 9522A (“Daytona”)Set Command: +CAR=This command switches the type of audio output between analog, digital and mute (no audio output).Valid values for are as follows:0 mute1 analog2 digitalRead Command: +CAR?This command queries the current audio setting. Response is in the form:+CAR: Test Command: +CAR=?This command lists the supported values of . Response is in the form:+CAR: (list of supported values of )Version 2.6March 30, 2006 68
ISU AT Command ReferencePhase VI AT Commands10 Phase VI AT Commands10.1 In – Identification (Revised)Requests the ISU to display information about itself.0 “2400” (traffic channel rate for IRIDIUM data/fax)1 “0000” (ROM checksum which is not supported so zero is output)2 “OK” (result of ROM checksum verification which is not supported so OK is always output)3 “XXXXXXXX” (Software revision level)4 “IRIDIUM” (Product description)5 “XXXX” (Country code)6 “XXX” (Factory identity)7 “XXXXXXXX” (Hardware specification)10.2 +CIER – Indicator Event ReportingSet Command: +CIER=[[,[,]]]The set command enables or disables sending of the +CIEV unsolicited result code by the ISU in case ofindicator state changes. controls the processing of the +CIEV unsolicited result codes.:0 Disable indicator event reporting; do not send +CIEV unsolicited result codes to theDTE; buffer the most recent indicator event for each indicator in the ISU. (default)1 Enable indicator event reporting; buffer the most recent +CIEV unsolicited result codefor each indicator when the data port is not in command mode, and flush them to theDTE on return to command mode; otherwise forward events directly to the DTE.:Control reporting of “signal quality” indicator changes.0 No “signal quality” indicator reporting.1 Enable “signal quality” indicator reporting using result code+CIEV:0,where is:0 Equivalent to 0 bars displayed on the ISU signal strength indicator.1 Equivalent to 1 bar displayed on the ISU signal strength indicator.2 Equivalent to 2 bars displayed on the ISU signal strength indicator.3 Equivalent to 3 bars displayed on the ISU signal strength indicator.4 Equivalent to 4 bars displayed on the ISU signal strength indicator.5 Equivalent to 5 bars displayed on the ISU signal strength indicator.When enabled, the signal quality indicator is reported only when the signal strength changes.:Control reporting of “service availability” indicator changes.0 No “service availability” indicator reporting.Version 2.6March 30, 2006 69
Page 1 and 2:
Version 2.6ISU AT Command Reference
Page 3 and 4:
ISU AT Command ReferenceRevision Hi
Page 5 and 6:
ISU AT Command ReferenceTable of Co
Page 7 and 8:
ISU AT Command ReferenceTable of Co
Page 9 and 10:
ISU AT Command ReferenceIntroductio
Page 11 and 12:
ISU AT Command ReferenceIntroductio
Page 13 and 14:
ISU AT Command ReferenceModem Overv
Page 15 and 16:
ISU AT Command ReferenceCommand Ove
Page 17 and 18:
ISU AT Command ReferenceCommand Ove
Page 19 and 20:
ISU AT Command ReferencePhased Impl
Page 21 and 22:
ISU AT Command ReferencePhased Impl
Page 23:
ISU AT Command ReferencePhase I AT
Page 26 and 27: ISU AT Command ReferencePhase I AT
Page 38: ISU AT Command ReferencePhase I AT
Page 42 and 43: ISU AT Command ReferencePhase II AT
Page 56 and 57: ISU AT Command ReferencePhase III A
Page 66 and 67: ISU AT Command ReferencePhase IV AT
Page 78 and 79: ISU AT Command ReferencePhase VI AT
Page 90 and 91: ISU AT Command ReferenceS-Register
Page 96 and 97: ISU AT Command ReferenceSummary of
Page 98 and 99: ISU AT Command ReferenceInformative
show all

ISU AT Command Reference

Create successful ePaper yourself

Delete template?

Save as template?