Sun Hydraulics Catalog - BIBUS SK, sro

Cartridge Control KitsService Kit No.DescriptionUse specifically withControl/CartridgeDescriptionNotesAdjustmentScrew Kit991-006AdjustmentScrew Kit991-010TamperResistant Cover(Zinc plated steel)991-000991-001991-002991-003991-004991-001-A00991-002-A00991-003-A00991-004-A00991-032991-033991-032-A00991-033-A00Key Lock Kit993-008KHandknob Kit(Plastic)991-211991-222(Plastic)PanelHandknob Kit(Plastic)991-215PanelHandknob Kit(Plastic)991-216HCalibratedHandknob Kit(Plastic)991-219991-220991-221All F controls(Zinc plated steel)All J controls(Zinc plated steel)All Sun Models with Ladjustment (ExceptCounterbalance, Series 1 and 2)Series 0 - 19,0 mm hexSeries 2 - 28,6 mm hexSeries 3 - 31,8 mm hexSeries 4 - 41,0 mm hexSeries 1 - 22,2 mm hexSeries 2 - 28,6 mm hex(Stainless steel)Series 3 - 31,8 mm hex(Stainless steel)Series 4 - 41,0 mm hex(Stainless steel)Series 1 - 22,2 mm hex(Stainless steel)For Series 1 and 2, CounterbalanceSeries 1 - 22,2 mm hex(Zinc plated steel)Series 2 - 28,6 mm hex(Zinc plated steel)Series 1 - 22,2 mm hex(Stainless steel)Series 2 - 28,6 mm hex(Stainless steel)For all Sun cartridges with Ladjustment (except Series 0 andcounterbalance cartridges).Use this kit to adapt all Lcontrols to K controls (exceptSeries 0 and counterbalancecartridges).K control for Series 0O controlsAll Series 1 cartridges22,2 mm hex, M20 threadO controlsAll Series 2 cartridges28,6 mm hex, 1”-14 threadH controlsAll series of flow controlsFDCB, NCEB, NCEC,NFDC, NFDD onlyFDEA, FDFA, NCFB,NCFC, NCGB, NCGC,NFEC, NFED, NFFC,NFFD onlyFDBA, NCCB, NCCC,NFCC, NFCD onlyAdjustScrewCapCoverLockAssemblyKeyLocknutHandknobAssemblyHandknobAssemblyLockKnobHandknob Lockring O-ringLocknutSealSealAdjustScrewWire Stop RingLockKnobAdapterLocknutPanel NutExistingCartridgeTo assure a complete seal on thestem - release all pressure on thecartridge after setting. Then...tighten locknut (and cap, on J).1. Adjust valve to desired settingand tighten locknut.2. Using an arbor press or a softhammer, install cover until itseats on cartridge hex.3. Cover is a press fit on cartridgeshoulder.1. Remove original wire stop ringand locknut.2. Thread on the adapter locknutand install new wire stop ringthrough slot provided.3. Adjust valve to desired settingand tighten adapter locknut.4. Slide lock assembly overadapter, lock and remove key.Only cartridges date stamped “41”or later and originally suppliedwith plastic knobs. Lock knobsnaps onto locknut furnished oncartridge.Only for cartridges originallysupplied with an H handknob.Valves can not be modified in thefield.Note: The H control isOnly available for the cartridgesshown to the left.Cartridge Control Kits continued on next page.Visit www.sunhydraulics.com for current list pricing and complete technical information on all Sun products.Int’l Shortcut Catalogue #999-901-312 179