Brocade Netiron CES and Brocade Netiron CER Devices Hardware ...

More documents

Recommendations

Info

3 Device installation Reverse rack mount position FIGURE 29 Reverse rack mount position You will need the following tools for installation: • #2 Phillips-head screwdriver • Four #12-24 screws (or as specified by rack type) to mount the Brocade device to the rack 40 Brocade NetIron CES and Brocade NetIron CER Devices Hardware Guide 53-1002425-03
Installation steps 1. Mount the device in the rack as illustrated in Figure 30. FIGURE 30 Installing the Brocade device in a rack I Device installation 3 2. Using a 2-hole grounding lug and a minimum #6 AWG grounding wire, ground the chassis to either a common bonding network or an isolated bonding network. 3. Proceed to “System power” on page 42. Brocade NetIron CES and Brocade NetIron CER Devices Hardware Guide 41 53-1002425-03
Page 1 and 2: 53-1002425-03 31 May 2012 Brocade N
Page 3 and 4: Contents About This Document Chapte
Page 5 and 6: Power supply replacement . . . . .
Page 7 and 8: About This Document Audience This d
Page 9 and 10: Notice to the reader Related public
Page 11 and 12: Product Overview Introduction Chapt
Page 13 and 14: Product overview Product overview 1
Page 15 and 16: Hardware features TABLE 2 Upgrade k
Page 17 and 18: Brocade NetIron CES 2048CX Hardware
Page 19 and 20: Brocade NetIron CER 2024F Hardware
Page 21 and 22: 1 Forty eight 100/1000 MbE SFP port
Page 23 and 24: Network interfaces Hardware feature
Page 25 and 26: Port regions Hardware features 1 Po
Page 27 and 28: DC power supplies Figure 20 shows t
Page 29 and 30: Connecting a Brocade Device to a Ne
Page 31 and 32: The following sub-net masks are sup
Page 33 and 34: Enabling and disabling the interfac
Page 35 and 36: Installation System unpacking DANGE
Page 37 and 38: CAUTION All fiber-optic interfaces
Page 39 and 40: Installation precautions 3 CAUTION
Page 41 and 42: Redundant power supply installation
Page 43 and 44: 9. Connect the plug end of the powe
Page 45 and 46: Redundant power supply installation
Page 47 and 48: Installing the device in a rack Dev
Page 49: Mid rack mount position FIGURE 28 M
Page 53 and 54: Operation verification Operation ve
Page 55 and 56: PC or terminal attachment 3 The sof
Page 57 and 58: Device Management Applications Fami
Page 59 and 60: TABLE 11 CLI line editing commands
Page 61 and 62: CLI Functionality 4 Brocade# ? appe
Page 63 and 64: TABLE 12 Special characters for reg
Page 65 and 66: Hardware Maintenance Hardware maint
Page 67 and 68: Power supply replacement 5 This com
Page 69 and 70: Power supply replacement 5 7. Inser
Page 71 and 72: FIGURE 36 The DC wiring assembly 1
Page 73 and 74: Power supply replacement 5 7. With
Page 75 and 76: TABLE 13 LEDs for power and fans (l
Page 77 and 78: Replacing the fan tray Replacing th
Page 79 and 80: 1 Bail latch Fiber optic module rep
Page 81 and 82: Regulatory Statements U.S.A. Append
Page 85 and 86: Taiwan Russia Taiwan A English tran
Page 87 and 88: Caution and Danger Notices Cautions
Page 89 and 90: Cautions B CAUTION Make sure you in
Page 91 and 92: Danger Danger B CAUTION Changes or
Page 93 and 94: Danger B WARNING If the installatio
Page 95 and 96: Hardware Specifications This chapte
Page 97 and 98: Operating environment Hardware spec
Page 99 and 100: Port specifications This section pr
Page 101 and 102:
Power cords Power cords C The types
Page 103:
Power cords C NOTE NEMA 5-15P shoul
show all

Brocade Netiron CES and Brocade Netiron CER Devices Hardware ...

Create successful ePaper yourself

Delete template?

Save as template?