Brocade Netiron CES and Brocade Netiron CER Devices Hardware ...
Brocade Netiron CES and Brocade Netiron CER Devices Hardware ...
Brocade Netiron CES and Brocade Netiron CER Devices Hardware ...
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
TABLE 13 LEDs for power <strong>and</strong> fans (located on front of device (Continued))<br />
LED State Meaning<br />
Power supply replacement 5<br />
PS1 (labeled P1) Off Power supply 1 is not installed or is not<br />
providing power.<br />
The LEDs for Fan, PS1 <strong>and</strong> PS2 are located on the right side of the front panel for <strong>Brocade</strong> NetIron<br />
<strong>CES</strong> <strong>and</strong> <strong>Brocade</strong> NetIron <strong>CER</strong> 2024 models (On the <strong>Brocade</strong> NetIron <strong>CES</strong> 2048 <strong>and</strong> <strong>Brocade</strong><br />
NetIron <strong>CER</strong> 2048 models, these LEDs are located on the left side of the front panel).<br />
The software regularly polls the hardware for power status information. You can display the status<br />
information from any management session. In addition, the software automatically generates a<br />
Syslog message <strong>and</strong> SNMP trap if a status change occurs.<br />
Displaying the status of the power supplies<br />
You can display the status of the power supplies by entering the show chassis comm<strong>and</strong> at any<br />
level of the CLI. The display shows whether a power supply is installed in the specified power supply<br />
slot <strong>and</strong> the status of the power supply. If you are not already attached to a terminal or a PC running<br />
terminal emulation, see “PC or terminal attachment” on page 45<br />
<strong>Brocade</strong>> show chassis<br />
*** <strong>Brocade</strong> NetIron <strong>CES</strong> 2048CX ***<br />
Amber Power supply 1 is installed, but not connected<br />
or a fault is detected.<br />
Green Steady Power supply 1 is installed <strong>and</strong> is functioning<br />
normally.<br />
Green Blinking Power supply 1 has input power, but is not<br />
enabled <strong>and</strong> has no output power.<br />
PS2 (labeled P2) Off Power supply 2 is not installed or is not<br />
providing power.<br />
Amber Power supply 2 is installed, but not connected<br />
or a fault is detected.<br />
Green Steady Power supply 2 is installed <strong>and</strong> is functioning<br />
normally.<br />
Green Blinking Power supply 2 has input power, but is not<br />
enabled <strong>and</strong> has no output power.<br />
---POWERS ---<br />
Power 1 ( 3I50 - AC 504W): Installed (OK)<br />
Power 2: not present<br />
Total power budget for system = 504 W<br />
--- FANS ---<br />
Metro fan tray (fan 1): Status = OK, Speed = LOW (50%)<br />
Metro fan tray (fan 2): Status = OK, Speed = LOW (50%)<br />
Metro fan tray (fan 3): Status = OK, Speed = LOW (50%)<br />
Metro fan tray (fan 4): Status = OK, Speed = LOW (50%)<br />
Metro fan tray (fan 5): Status = OK, Speed = LOW (50%)<br />
Metro fan tray (fan 6): Status = OK, Speed = LOW (50%)<br />
--- TEMPERATURE READINGS ---<br />
CPU: Board 32.50C Chip 41.6C<br />
481XG PPCR1: Board 32.50C Chip 43.31C<br />
<strong>Brocade</strong> NetIron <strong>CES</strong> <strong>and</strong> <strong>Brocade</strong> NetIron <strong>CER</strong> <strong>Devices</strong> <strong>Hardware</strong> Guide 65<br />
53-1002425-03
Change language