Programming Manual Elektor Proton Robot - ELEKTOR.se

More documents

Recommendations

Info

Audio BoostDescriptionSets a boost value for bass and/or treble.To set the default start-up boost value, use Settings for non-volatile (start-up) settings.FormatPC B [boost]ParametersNote• boost is a value between 0 and 65535.o Treble boost can be set from -12 to +10.5 dB boost (in 1.5 dB steps) at and abovefrequencies ranging from 1000 to 15000 Hz (in 1000 Hz steps).o Bass boost can be set from 0 to 15 dB boost (in 1 dB steps) below frequenciesranging from 20 to 150 Hz (in 10 Hz steps).o To calculate the value for boost:• treble boost = (treble amplitude[see table below] * 16) + treblefrequency/1000• bass boost = ((bass amplitude * 16) + (bass frequency/10)• boost = treble boost * 256 + bass boosto A boost value of 0 will turn off the audio enhancement.Treble amplitude is a twos-complement value for the amplitude.Treble amplitude value Twos-complement Binary Hexadecimal Treble boost (dB)15 -8 1111 F -12 dB14 -7 1110 E -10.5 dB13 -6 1101 D -9 dB12 -5 1100 C -7.5 dB11 -4 1011 B -6 dB10 -3 1010 A -4.5 dB9 -2 1001 9 -3 dB8 -1 1000 8 -1.5 dB0 0 0000 0 0 dB (boost off)Bart Huyskens Manual Elektor Proton V1.0 3 April 2011 116
1 1 0001 1 +1.5 dB2 2 0010 2 +3 dB3 3 0011 3 +4.5 dB4 4 0100 4 +6 dB5 5 0101 5 +7.5 dB6 6 0110 6 +9 dB7 7 0111 7 +10.5 dBResponse FormatNULL | response | EnnIf no parameters are given, then response is the current boost setting.ExampleTreble boost frequency: 10 kHz (and above)Treble boost amplitude: +10.5 dBBass boost frequency: 60 Hz (and below)Bass boost amplitude: +15 dBtreble boost = (7 * 16) + 10000/1000= 112 + 10 = 122bass boost = (15 * 16) + 60/10= 240 + 6 = 246Boost value = 122 * 256 + 246= 31478PC B 31478To retrieve the current boost value:PC B31748To turn off boost:PC B 0Bart Huyskens Manual Elektor Proton V1.0 3 April 2011 117
Page 1 and 2:
V1.0Programming ManualElektor Proto
Page 3 and 4:
Communications Protocol ...........
Page 5 and 6:
Blok schematic:Bart Huyskens Manual
Page 7 and 8:
Different modules on PCB levelBart
Page 9 and 10:
AVR add-on board• The AVR board h
Page 11 and 12:
Servo moduleSCL-SDAHeadSCL-SDAUS di
Page 13 and 14:
List of all the connectors on the m
Page 15 and 16:
J26J27J28J29 +-J30J31J33J34J35GND12
Page 17 and 18:
char I2C_RECEIVE_BYTE(char Last);vo
Page 19 and 20:
How to set up Flowcode 4 (PIC) for
Page 21 and 22:
How to set up Flowcode 4 (AVR) for
Page 23 and 24:
How to set op AVRSTUDIO - WINAVR /
Page 25 and 26:
Click on the gear-logo “Edit curr
Page 27 and 28:
Make sure that your fuses tab scree
Page 29 and 30:
How to set up MPLAB - HITECH C Lite
Page 31 and 32:
We choose not to add any file to th
Page 33 and 34:
•Copy paste the “PIC_PROTON_LIB
Page 35 and 36:
Bart Huyskens Manual Elektor Proton
Page 37 and 38:
}{PORTD = 0x0F;__delay_ms(200);PORT
Page 39 and 40:
PIC16F887Demoprogram Flowcode PIC V
Page 41 and 42:
These are 2 normally open push butt
Page 43 and 44:
• After the readbyte instruction
Page 45 and 46:
READ DATA FROM THE SLAVEFor example
Page 47 and 48:
void main(){// init AD & Option reg
Page 49 and 50:
Experience: We use this LCD in I2C
Page 51 and 52:
Commands to write in the command re
Page 53 and 54:
Custom char generatorCustom charact
Page 55 and 56:
The servo motors in the head and th
Page 57 and 58:
This robot can be equipped with up
Page 59 and 60:
Although the signal for the positio
Page 61 and 62:
The head with ldr’s, RGB-led’s
Page 63 and 64:
Head I2C Slave address = 0x10Index
Page 65 and 66: Proton robot developer’s notes:Th
Page 67 and 68: When a ranging command in cm is giv
Page 69 and 70: address of a sonar currently at 0xE
Page 71 and 72: The MD25 motor driver moduleThis pr
Page 75 and 76: The MD25 has 17 registers numbered
Page 77 and 78: ultimate speed, the MD25 has a regi
Page 79 and 80: Changing the I2C Bus AddressTo chan
Page 81 and 82: The line sensor module with 3 IR li
Page 83 and 84: Photo of the 3 line follow sensorsT
Page 85 and 86: Analogue to digital conversion expl
Page 87 and 88: }}Proton robot developer’s notes:
Page 89 and 90: RS232 communication explainedRS-232
Page 93 and 94: • Supportso MMC, SDC, SDHC card f
Page 95 and 96: Communications ProtocolDescriptionT
Page 97 and 98: Prompt CharacterSetting name: PThis
Page 99 and 100: BoostSetting name: BSets the defaul
Page 101 and 102: Input/Output Interface SettingsInpu
Page 103 and 104: SettingsDescriptionNon-volatile set
Page 105 and 106: Play NextDescriptionThis plays the
Page 107 and 108: StopDescriptionStops playback.Forma
Page 109 and 110: Playback StatusDescriptionThis show
Page 111 and 112: Play ToneDescriptionThis command pl
Page 113 and 114: Reset AudioDescriptionResets the au
Page 115: Loop CountDescriptionGets or sets t
Page 119 and 120: This command will copy data from an
Page 121 and 122: CloseDescriptionCloses an open file
Page 123 and 124: Parameters• path is the absolute
Page 125 and 126: InfoDescriptionGives the file posit
Page 127 and 128: Card InfoDescriptionGets card speci
Page 129 and 130: List DirectoryDescriptionThe List D
Page 131 and 132: L /PICTURES/*.JPG«sp»----A 2008/0
Page 133 and 134: RenameDescriptionRenames/moves a fi
Page 135 and 136: O 1 R /LOGS/JANUARY/JAN03.LOGOpen a
Page 137 and 138: DescriptionYou can read up to 512 b
Page 139 and 140: Read LineDescriptionThe Read Line c
Page 141 and 142: WriteDescriptionYou can write up to
Page 143 and 144: E /LOG.TXTO 1 RW /LOG.TXTS E0I 10/0
Page 145 and 146: Table of SettingsCommunication Sett
Page 147 and 148: Input/Output Interface SettingsSett
Page 149 and 150: Proton main program for PIC in C:/*
Page 151 and 152: void UART_STRING_RECEIVE(char *rece
Page 153 and 154: }SSPBUF=Data;//Send bytewhile((PIR1
Page 155 and 156: }}// Writes an integer value to the
Page 157 and 158: s++;}}//bit STRING_IN( const char *
Page 159 and 160: eturn;}}}}}/***********************
Page 161 and 162: Proton main program for AVR in C:/*
Page 163 and 164: char STR_PREFIX( const char *p, con
Page 165 and 166: }TWCR = (1
Page 167 and 168:
LCD_WRITE_STRING(String);alsoLCD_WR
Page 169 and 170:
n--;}}//bit char_in( char c, const
Page 171 and 172:
}} else {_delay_us( 100 );t++;if( t
Page 173 and 174:
Cheat sheet C - for Hitech C compil
Page 175:
Version changes summary09/04/2011 v
show all

Programming Manual Elektor Proton Robot - ELEKTOR.se

Create successful ePaper yourself

Delete template?

Save as template?