MC-Balance User Manual 4.0.UK.00

More documents

Recommendations

Info

1. IntroductionThank you for purchasing a Movacolor metering device. This manual is addressed to operatorsand qualified technicians taking care of the metering of dry additives to ensure correct use of theMovacolor dosing unit.i IMPORTANT NOTE: THIS MANUAL MUST BE READ BEFORE INSTALLING THE DOSINGUNIT. KEEP THIS MANUAL IN A PLACE ACCESSIBLE FOR ALL OPERATORS.1.1 SymbolsiImportant note1.2 TermsAttention; safety regulations for the operatorOperator:Qualified Technician:A person charged to operate, adjust, maintain and clean the machine.A specialized, suitable trained person authorized to execute theinstallation, non-routine maintenance, or repairs requiring specialknowledge of the machine and how it operates.1MC-Balance manual
2. General information2.1 SafetyThe equipment is only designed and may only be used for the dosing of dry additives.Any use that is not in conformity with the instructions is considered improper and as suchfrees the manufacturer from any liability regarding damage to things and/or persons.Before switching on the unit for the first time, ensure that the mains power voltageapplied is between 80 and 260Vac.Always switch off the Movacolor control cabinet and disconnect the mains power plug fromelectrical power before performing maintenance.Ensure that all parts are securely fixed to the extruder or injection molding machine.Dangerous voltages are present inside the control cabinet for up to 2 minutes after it hasbeen switched off.2.2 CertificationThe Movacolor dosing unit is designed and produced in conformity with the following Europeanregulations:• standards for machinery (health, safety, environment)• EMC (electromagnetic compatibility)• VEM (safety electric material)• 98/37/EC, Annex 1(See the declaration of conformity, Appendix E)2.3 Operating environmental conditions• The unit must be protected against weather conditions• Operating temperature -20 to +70 degr. C.• Protection class: IP-502MC-Balance manual
Page 1: MC-BalanceUser Manual 4.0.UK.00Soft
Page 6 and 7: 3. Overview Dosing unit3.1 MC-Balan
Page 8 and 9: 4. Metering principleThe Dosing Cyl
Page 10: All Movacolor dosing units are stan
Page 14 and 15: APPENDIX A SHOWS THE PRINT VIEW WHI
Page 16 and 17: 7.2 Start up & LoginDirectly after
Page 18 and 19: 7.4 ConfigurationFor initial setup
Page 20 and 21: The maximum voltage that can be app
Page 22 and 23: Configuration: DeviationalarmSettin
Page 24 and 25: 7.5 Loadcell calibrationWhen using
Page 26 and 27: How to make a material calibration?
Page 28 and 29: INJECTION MOULDINGThe following par
Page 30 and 31: 7.8 Auto/Manual regulation mode & S
Page 32 and 33: 7.10 Filling the hopper.MANUAL FILL
Page 34 and 35: GeneraliThe hopper loader is only a
Page 36 and 37: Recommended settings for ME hopper
Page 38 and 39: WARNINGSAll warnings are self elimi
Page 40 and 41: 7.14 Event LOGSetting changes made
Page 42 and 43: 9. Trouble shootingProblem : The ba
Page 44 and 45: 41MC-Balance manualPOTENTIAL FREE P
Page 46 and 47: APPENDIX D: MC-Bal. Drawings Genera
Page 48 and 49: General dimension MC-Balance + MV25
Page 50 and 51: APPENDIX E: MC-Bal. Decl. of Confor

MC-Balance User Manual 4.0.UK.00

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?