Power Spot 250 User Manual (pdf) - Elation Professional

More documents

Recommendations

Info

Power Spot 25012. DMX Input Jack – This jack is used to receive an incoming DMX signal orMaster/Slave signal.13. DMX Output Jack – This jack is used to transmit the incoming DMX signal toanother DMX fixture, or transmit a Master/Slave signal to the next Power Wash250 in the chain. For best results in DMX or Master/Slave mode terminate thisjack if it is the last fixture in the chain. See “Terminator” on page 14.14. Power Switch – This switch is used to control main power to the fixture.15. Fuse Holder – This housing stores a 6.3 amp (3.15 amp 220v) GMA protectivefuse. Never defeat the fuse, the fuse is designed to protect the electronics in theevent of sever power fluctuations. Always be sure to replace the fuse with an exactmatch as to the one being replaced, unless otherwise told to do so by anauthorized Elation® service technician.16. Cooling Fan - This fixture is equipped with a high velocity variable fan to aid in thecooling process. This fan is designed to vary its’ velocity at different operatingtemperatures, to provide better cooling when the fixture reached higher operatingtemperatures associated with long usage. Be sure to never obstruct the coolingfan during normal usage. Also, be sure to keep this vent clean at all times. Ablocked or malfunctioning cooling system may shorten lamp life and fixturereliability.©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 10
Power Spot 2502. Preparation and Installation2.1 MountingThe POWER SPOT 250 is fully operational in two different mounting positions,hanging upside from a ceiling or set on a flat level surface. To avoid internaldamage to the unit, never mount the unit on its side as illustrated below. Be surethis fixture is kept at least 0.5m away from any flammable materials (decorationetc.). Install a safety cable that can hold at least 10 times the weight of the fixture.Never use the carrying handles for secondary attachment.2.1.1 ClampsRefer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-217 for proper installation in EuropeTo ensure proper installation, only qualified staff should attemptinstallation.The POWER SPOT 250 has been designed to hold multiple clamps to thebottom of the unit in several different orientations. Always use an appropriatelyrated clamp to mount this unit to truss. Refer to the printed instructions on thebottom of the fixture for proper clamp installation.©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 11
Page 1 and 2: User ManualSoftware Version 1.60 Re
Page 3 and 4: Power Spot 250Table of ContentsIntr
Page 5 and 6: Power Spot 250INTRODUCTION: Congrat
Page 7 and 8: Power Spot 250Safety InstructionsTh
Page 9: Power Spot 2501. Lens Assembly - Th
Page 13 and 14: Power Spot 2502.3 Connections2.3.1
Page 15 and 16: Power Spot 2502.8 5-Pin XLR DMX Con
Page 17 and 18: Power Spot 250SHUT Shutter, Channel
Page 19 and 20: Power Spot 250sound impulse will tr
Page 21 and 22: Power Spot 2508 Prism, Prism rotati
Page 23 and 24: Power Spot 250Function Value Remark
Page 25 and 26: Power Spot 250Mode button to cancel
Page 27 and 28: Power Spot 2504. OperationOperating
Page 29 and 30: Power Spot 2505. DMX CHANNEL SELECT
Page 31 and 32: Power Spot 250Channel Function Time
Page 33: Power Spot 2506. Lamp ReplacementFo
Page 36 and 37: Power Spot 2507. Fuse ReplacementCa
Page 38 and 39: Power Spot 250Special Notice:If you
Page 40 and 41: Power Spot 250depends on the enviro
Page 42 and 43: Power Spot 2502 YEAR (730 DAYS) LIM
Page 44 and 45: LASER WARNING LABELSDANGER! !VISIBL
Page 46 and 47: ©Elation Professionals® Los Angel

Power Spot 250 User Manual (pdf) - Elation Professional

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?