Power Spot 250 User Manual (pdf) - Elation Professional

More documents

Recommendations

Info

Power Spot 250Channel Function Time and Value DMX HEX %14) SpeedPan/TiltPan/Tilt relative movement 0-15 00-0F 0-6Pan/Tilt, Slow - FastPan min. 530° = 200s 16-255 10-FF 7-100This channel controls both the Pan Pan max. 530° = 2.65sand Tilt speeds. This channel will also Tilt min. 285° = 110scontrol the speed of all the built-in Tilt max. 285° = 1.8smovements activated throughchannel 13.15) Laser Laser OffLaser Strobe, Sow – FastLaser On0-1516-239240-2550-67-9697-100Lamp ON Shutter open 240-255 F0-FF 94-100Lamp OFFChannel 12 (min. 3 sec.) (Only if230-249 6E-9F 92-97shutter is closed, channel 9 = 0 -15)©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 32
Power Spot 2506. Lamp ReplacementFor a proper and safe lamp change, please read this chapter carefully and follow allinstructions.6.1 Safety Regulations• Pull out the main plug!• Wait min. 20 minutes after the last operation to cool down the fixture.• Don’t touch the bulb of the lamp with bare fingers (this can cause damages.• Before you put the POWER SPOT 250 into operation close the casing, otherwiseyour retina can be hurt!6.2 Lamp Change6.2.1 Be sure the unit is disconnected from it’smain power supply.6.2.2 Remove the upper shell of the protectivecover by removing the 4 retaining Phillipsscrews, 2 located on the front and 2 locatedon the rear of the head.6.2.3 Once the outer cover has been removed,expose the lamp by removing the lampcover plate. Remove the lamp cover plateby unscrewing 3 thumb screws. Refer tothe illustration on the left.6.2.4 Gently remove the old lamp from it’s socket.If the old lamp has exploded be sure toremove all of the old lamp fragments toprevent damage to the internalcomponents.fastening screwlamplampcover plate6.2.5 Replace the lamp with an approved replacement type. Be sure to follow all thelamp handleing procedures included with your new lamp. Never handle the newlamp with your bare hands, the oils from your skin may damage the lamp. Alwaysreplace with the lamp with a lamp that meets the orginal lamp specification, failureto do so may damage the unit and will void your manufactures warranty.6.2.6 Before reassembing the unit, be sure to adjust the lamp distance from the main©Elation Professionals® Los Angeles, Ca. - wwww.ElationLighting.com - Page 33
Page 1 and 2: User ManualSoftware Version 1.60 Re
Page 3 and 4: Power Spot 250Table of ContentsIntr
Page 5 and 6: Power Spot 250INTRODUCTION: Congrat
Page 7 and 8: Power Spot 250Safety InstructionsTh
Page 9 and 10: Power Spot 2501. Lens Assembly - Th
Page 11 and 12: Power Spot 2502. Preparation and In
Page 13 and 14: Power Spot 2502.3 Connections2.3.1
Page 15 and 16: Power Spot 2502.8 5-Pin XLR DMX Con
Page 17 and 18: Power Spot 250SHUT Shutter, Channel
Page 19 and 20: Power Spot 250sound impulse will tr
Page 21 and 22: Power Spot 2508 Prism, Prism rotati
Page 23 and 24: Power Spot 250Function Value Remark
Page 25 and 26: Power Spot 250Mode button to cancel
Page 27 and 28: Power Spot 2504. OperationOperating
Page 29 and 30: Power Spot 2505. DMX CHANNEL SELECT
Page 31: Power Spot 250Channel Function Time
Page 36 and 37: Power Spot 2507. Fuse ReplacementCa
Page 38 and 39: Power Spot 250Special Notice:If you
Page 40 and 41: Power Spot 250depends on the enviro
Page 42 and 43: Power Spot 2502 YEAR (730 DAYS) LIM
Page 44 and 45: LASER WARNING LABELSDANGER! !VISIBL
Page 46 and 47: ©Elation Professionals® Los Angel

Power Spot 250 User Manual (pdf) - Elation Professional

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?