AT Command Set - Olitec

More documents

Recommendations

Info

PH-NET PINPH-NET PUKPH-NS PINPH-NS PUKPH-SP PINPH-SP PUKPH-C PINPH-C PUKSee Chapters for information on lock types.ME is waiting for network personalisation passwordME is waiting for network personalisation unblockingpasswordME is waiting for network subset personalisationpasswordME is waiting for network subset unblockingpasswordME is waiting for service provider personalisationpasswordME is waiting for service provider personalisationunblocking passwordME is waiting for corporate personalisationpasswordME is waiting for corprorate personalisation unblockingpasswordWrite commandAT+CPIN=[,]ResponseThe write command lets the ME store the entered password. This may be forexample the SIM PIN1 to register to the GSM network, or the SIM PUK1 to replacea disabled PIN with a new one, or the PH-SIM PIN if the client has takenprecautions for preventing damage in the event of loss or theft etc. See abovefor the list of passwords.OKIf error is related to ME functionality:+CME ERROR: If no PIN request is pending (for example if PIN authentication has been doneand the same PIN is entered again) ME responds +CME ERROR: operation notallowed. No action is required from your part.Parameterpassword (string type), usually SIM PIN1.If the requested password was a PUK, such as SIM PUK1 or PH-SIM PUK or PH-FSIM PUK or another password, then mustbe followed by .if the requested code was a PUK: specify a new password or restorethe former disabled password. See Chapter 4.35.1 for moreinformation about when you may need to enter the PUK.ReferenceGSM 07.07Note• Caution: After entering a password with AT+CPIN all other commands thatneed access to data on the SIM card may be blocked for up to 20 seconds!• Successful PIN authentication only confirms that the entered PIN was recognizedand correct. The output of the result code OK does not necessarilyimply that the mobile is registered to the desired network.Typical example: PIN was entered and accepted with OK, but the ME failsto register to the network. This may due to missing network coverage, deniednetwork access with currently used SIM card, no valid roaming agreementbetween home network and currently available operators etc.MC35 offers various options to verify the present status of network registration:For example, the AT+COPS? (Chapter 4.30) command indicates thecurrently used network. With AT+CREG (Chapter 4.41) you can also checkthe current status and activate an unsolicited result code which appearswhenever the status of the network registration changes (e.g. when the MEis powered up, or when Page the 110 network of 207 cell changes).
the current status and activate an unsolicited result code which appearswhenever the status of the network registration changes (e.g. when the MEis powered up, or when the network cell changes).• Wait 10 seconds after PIN input before using SMS related commands.• and can also be entered in quotation marks (e.g. ”1234”).• To check the number of remaining attempts to enter the passwords use theAT^SPIC command.• See also Chapter 8.2 “Summary of PIN requiring AT Commands“.• See Chapters 4.38 for information on passwords.Page 111 of 207
Page 1 and 2:
AT Command SetDocument non contract
Page 3 and 4:
2.35 AT&F Set all current parameter
Page 5 and 6:
5.14 AT+CSDH Show SMS text mode par
Page 7 and 8:
FiguresFigure 1: AT audio programmi
Page 9 and 10:
4.50 131 AT+VTS5.45.5135138AT+CMGLA
Page 11 and 12:
1 Introduction1.1 Scope of the docu
Page 13 and 14:
1.3 ConventionsThroughout the docum
Page 15 and 16:
1.5 Supported character setsThe ME
Page 17 and 18:
2 Standard V.25ter AT CommandsThese
Page 19 and 20:
2.5 ATD Mobile originated call to d
Page 21 and 22:
2.6 ATD> Originate call to phone nu
Page 23 and 24:
2.7 ATD> Originate call to phone nu
Page 25 and 26:
2.9 ATDI Mobile originated call to
Page 27 and 28:
2.11 ATE Enable command echoWrite c
Page 29 and 30:
2.15 ATL Set monitor speaker loudne
Page 31 and 32:
2.21 ATS3 Write command line termin
Page 33 and 34:
2.27 ATS10 Set disconnect delay aft
Page 35 and 36:
2.32 ATZ Set all current parameters
Page 37 and 38:
2.35 AT&F Set all current parameter
Page 39 and 40:
2.36 AT&S Set circuit Data Set Read
Page 41 and 42:
2.38 AT&W Store current configurati
Page 43 and 44:
2.42 AT+GMR Request TA revision ide
Page 45 and 46:
2.45 AT+IPR Set fixed local rateTes
Page 47 and 48:
3 AT Commands for FAXThe following
Page 49 and 50:
3.4 AT+FCIG Query or set the Local
Page 51 and 52:
3.8 AT+FDCC Query or set capabiliti
Page 53 and 54:
3.10 AT+FDIS Query or set session p
Page 55 and 56:
3.13 AT+FET End a page or documentW
Page 57 and 58:
3.19 AT+FPHCTO DTE Phase C Response
Page 59 and 60: 3.25 AT+FTM Transmit DataTest comma
Page 61 and 62: 4 AT Commands originating from GSM
Page 63 and 64: indicate year (two last digits), mo
Page 65 and 66: 4.3 AT+CAMM Accumulated call meter
Page 67 and 68: 4.5 AT+CBST Select bearer service t
Page 69 and 70: tion:1 voice2 data4 fax8 short mess
Page 71 and 72: 4.7 AT+CCLK Real Time ClockTest com
Page 73 and 74: 4.9 AT+CCWA Call waitingTest comman
Page 75 and 76: 4.10 AT+CEER Extended error reportT
Page 77 and 78: can issue AT+CFUN=1 to stop power s
Page 79 and 80: 4.11.1 Wake up the ME from SLEEP mo
Page 81 and 82: 4.15 AT+CGSN Request product serial
Page 83 and 84: 4.19 AT+CIND Indicator controlMC35
Page 85 and 86: 4.20 AT+CLCC List current calls of
Page 87 and 88: “PF”“PN”“PU”“PP”“
Page 89 and 90: AT+CPIN=9999OKTo lock the mobile to
Page 91 and 92: 4.21.3 Examples: Call barringPlease
Page 93 and 94: 4.23 AT+CLIR Calling line identific
Page 95 and 96: 4.25 AT+CMEE Report mobile equipmen
Page 97 and 98: eceived. See also Chapter 4.46."ser
Page 99 and 100: 4.28 AT+CMUX Enter multiplex modeMC
Page 101 and 102: Command Behaviour on channel 1 Diff
Page 103 and 104: 4.30 AT+COPS Operator selectionThis
Page 105 and 106: 4.31 AT+CPAS Mobile equipment activ
Page 107 and 108: 4.33 AT+CPBS Select phonebook memor
Page 109: 4.35 AT+CPIN Enter PINTest commandA
Page 113 and 114: SIM locks:Call barring:These are fa
Page 115 and 116: changes to READY. After 300s, a rep
Page 117 and 118: 4.38 AT+CPWD Change passwordUse thi
Page 119 and 120: To specify a new "PS" lock password
Page 121 and 122: 4.40 AT+CRC Set Cellular Result Cod
Page 123 and 124: If =1 and there is a change in the
Page 125 and 126: 4.43 AT+CRSM Restricted SIM accessT
Page 127 and 128: 4.45 AT+CSNS Single Numbering Schem
Page 129 and 130: 4.47 AT+CSSN Supplementary service
Page 131 and 132: 4.49 AT+VTD= Tone durationTest comm
Page 133 and 134: 5 AT commands originating from GSM
Page 135 and 136: 5.4 AT+CMGL List SMS messages from
Page 137 and 138: converted into characters; type of
Page 139 and 140: GSM 03.40 TP- Destination-Address A
Page 141 and 142: 5.6 AT+CMGS Send SMS messageTest co
Page 143 and 144: 5.7 AT+CMGW Write SMS message to me
Page 145 and 146: 5.8 AT+CMSS Send SMS message from s
Page 147 and 148: 5.10 AT+CNMI New SMS message indica
Page 149 and 150: ReferenceGSM 07.05General remarks:
Page 151 and 152: no matter whether or not there is f
Page 153 and 154: 5.13 AT+CSCB Select cell broadcast
Page 155 and 156: 5.15 AT+CSMP Set SMS text mode para
Page 157 and 158: 6 GPRS AT commands in accordance wi
Page 159 and 160: 6.1.3 AT+CGDATA Enter data stateTes
Page 161 and 162:
Packet Data Protocol type is a stri
Page 163 and 164:
Parameternumeric PDP Context Identi
Page 165 and 166:
OKat+cgqmin=1,1OKat+cgqmin?+CGQMIN:
Page 167 and 168:
numeric parameter for the precedenc
Page 169 and 170:
at+cgqreq=1,1OKat+cgqreq?+CGQREQ:1,
Page 171 and 172:
6.1.8 AT^SGAUTH Set type of authent
Page 173 and 174:
6.3.1 ATD *98# Request GPRS IP serv
Page 175 and 176:
6.4 Using GPRS AT commands (example
Page 177 and 178:
6.5 Using the GPRS dial command ATD
Page 179 and 180:
7.1 AT^SSTA Remote-SAT Interface Ac
Page 181 and 182:
7.3 AT^SSTGI Remote-SAT Get Informa
Page 183 and 184:
8 APPENDIX8.1 Summary of ERRORS and
Page 185 and 186:
8.1.3 Summary of CMS ERRORS related
Page 187 and 188:
Example 2The application tries to s
Page 189 and 190:
Message Meaning How to activateURC+
Page 191 and 192:
8.1.5 Result codesIndication Numeri
Page 193 and 194:
8.1.9 GSM release cause for Mobilit
Page 195 and 196:
Number Description50 Requested faci
Page 197 and 198:
Number Description309 Linked Respon
Page 199 and 200:
8.1.19 SIEMENS release cause for Em
Page 201 and 202:
AT commandRequired PINAT+CR PIN 1AT
Page 203 and 204:
AT command Test Read Write / NoteEx
Page 205:
*# code Functionality Possible resp
show all

AT Command Set - Olitec

Create successful ePaper yourself

Delete template?

Save as template?