AT Command Set - Olitec

More documents

Recommendations

Info

3.6 AT+FCQ Copy Quality CheckingTest commandAT+FCQ =?This command controls Copy Quality checking when receiving a fax.Response(list of supported copy quality checking s)OKParameterSee write commandRead commandAT+FCQ?Response OKParameterSee write commandWrite commandAT+FCQ =ResponseOKParameter 0 No copy quality checking. The ME will generate Copy QualityOK (MCF) responses to complete pages.1 ME can check 1-D phase data. The connected applicationmust check copy quality for 2-D phase C dataReferenceEIA PN-2388NoteUsed for for Faxclass 2 only.3.7 AT+FCR Capability to receiveWrite commandAT+FCR=ResponseOKParameter 0 ME will not receive message data. This can be used whenthe application has insufficient storage. The ME can sendand can be polled for a file.1 ME can receive message data.ReferenceEIA PN-2388NoteUsed for Faxclass 2 onlyPage 50 of 207
3.8 AT+FDCC Query or set capabilitiesTest commandAT+FDCC =?This command allows the connected application to sense and constrain thecapabilities of the facsimile DCE (=ME), from the choices defined in CCITTT.30 Table 2.Response(list of s), (list of s), (list of s), (list of s), (list of s),(list of s), (list of s), (list of s)OKParameterVR: Vertical Resolution, BR: Bit Rate, WD: Page Width, LN: Page Length, DF:Data Compression Format, EC: Error Correction Mode, BF: Binary FileTransfer Mode, ST: Scan Time/Line.Note: For further information see AT+FDIS, pg. 53Read commandAT+FDCC?Response OKParameterSee write commandWrite commandAT+FDCC=,,,,,,,ResponseOKParameterVR: Vertical Resolution, BR: Bit Rate, WD: Page Width, LN: Page Length, DF:Data Compression Format, EC: Error Correction Mode, BF: Binary FileTransfer Mode, ST: Scan Time/Line.Note: For further information see AT+FDIS, pg. 53ReferenceEIA PN-2388NoteUsed for Faxclass 2 onlyPage 51 of 207
Page 1 and 2: AT Command SetDocument non contract
Page 3 and 4: 2.35 AT&F Set all current parameter
Page 5 and 6: 5.14 AT+CSDH Show SMS text mode par
Page 7 and 8: FiguresFigure 1: AT audio programmi
Page 9 and 10: 4.50 131 AT+VTS5.45.5135138AT+CMGLA
Page 11 and 12: 1 Introduction1.1 Scope of the docu
Page 13 and 14: 1.3 ConventionsThroughout the docum
Page 15 and 16: 1.5 Supported character setsThe ME
Page 17 and 18: 2 Standard V.25ter AT CommandsThese
Page 19 and 20: 2.5 ATD Mobile originated call to d
Page 21 and 22: 2.6 ATD> Originate call to phone nu
Page 23 and 24: 2.7 ATD> Originate call to phone nu
Page 25 and 26: 2.9 ATDI Mobile originated call to
Page 27 and 28: 2.11 ATE Enable command echoWrite c
Page 29 and 30: 2.15 ATL Set monitor speaker loudne
Page 31 and 32: 2.21 ATS3 Write command line termin
Page 33 and 34: 2.27 ATS10 Set disconnect delay aft
Page 35 and 36: 2.32 ATZ Set all current parameters
Page 37 and 38: 2.35 AT&F Set all current parameter
Page 39 and 40: 2.36 AT&S Set circuit Data Set Read
Page 41 and 42: 2.38 AT&W Store current configurati
Page 43 and 44: 2.42 AT+GMR Request TA revision ide
Page 45 and 46: 2.45 AT+IPR Set fixed local rateTes
Page 47 and 48: 3 AT Commands for FAXThe following
Page 49: 3.4 AT+FCIG Query or set the Local
Page 53 and 54: 3.10 AT+FDIS Query or set session p
Page 55 and 56: 3.13 AT+FET End a page or documentW
Page 57 and 58: 3.19 AT+FPHCTO DTE Phase C Response
Page 59 and 60: 3.25 AT+FTM Transmit DataTest comma
Page 61 and 62: 4 AT Commands originating from GSM
Page 63 and 64: indicate year (two last digits), mo
Page 65 and 66: 4.3 AT+CAMM Accumulated call meter
Page 67 and 68: 4.5 AT+CBST Select bearer service t
Page 69 and 70: tion:1 voice2 data4 fax8 short mess
Page 71 and 72: 4.7 AT+CCLK Real Time ClockTest com
Page 73 and 74: 4.9 AT+CCWA Call waitingTest comman
Page 75 and 76: 4.10 AT+CEER Extended error reportT
Page 77 and 78: can issue AT+CFUN=1 to stop power s
Page 79 and 80: 4.11.1 Wake up the ME from SLEEP mo
Page 81 and 82: 4.15 AT+CGSN Request product serial
Page 83 and 84: 4.19 AT+CIND Indicator controlMC35
Page 85 and 86: 4.20 AT+CLCC List current calls of
Page 87 and 88: “PF”“PN”“PU”“PP”“
Page 89 and 90: AT+CPIN=9999OKTo lock the mobile to
Page 91 and 92: 4.21.3 Examples: Call barringPlease
Page 93 and 94: 4.23 AT+CLIR Calling line identific
Page 95 and 96: 4.25 AT+CMEE Report mobile equipmen
Page 97 and 98: eceived. See also Chapter 4.46."ser
Page 99 and 100: 4.28 AT+CMUX Enter multiplex modeMC
Page 101 and 102:
Command Behaviour on channel 1 Diff
Page 103 and 104:
4.30 AT+COPS Operator selectionThis
Page 105 and 106:
4.31 AT+CPAS Mobile equipment activ
Page 107 and 108:
4.33 AT+CPBS Select phonebook memor
Page 109 and 110:
4.35 AT+CPIN Enter PINTest commandA
Page 111 and 112:
the current status and activate an
Page 113 and 114:
SIM locks:Call barring:These are fa
Page 115 and 116:
changes to READY. After 300s, a rep
Page 117 and 118:
4.38 AT+CPWD Change passwordUse thi
Page 119 and 120:
To specify a new "PS" lock password
Page 121 and 122:
4.40 AT+CRC Set Cellular Result Cod
Page 123 and 124:
If =1 and there is a change in the
Page 125 and 126:
4.43 AT+CRSM Restricted SIM accessT
Page 127 and 128:
4.45 AT+CSNS Single Numbering Schem
Page 129 and 130:
4.47 AT+CSSN Supplementary service
Page 131 and 132:
4.49 AT+VTD= Tone durationTest comm
Page 133 and 134:
5 AT commands originating from GSM
Page 135 and 136:
5.4 AT+CMGL List SMS messages from
Page 137 and 138:
converted into characters; type of
Page 139 and 140:
GSM 03.40 TP- Destination-Address A
Page 141 and 142:
5.6 AT+CMGS Send SMS messageTest co
Page 143 and 144:
5.7 AT+CMGW Write SMS message to me
Page 145 and 146:
5.8 AT+CMSS Send SMS message from s
Page 147 and 148:
5.10 AT+CNMI New SMS message indica
Page 149 and 150:
ReferenceGSM 07.05General remarks:
Page 151 and 152:
no matter whether or not there is f
Page 153 and 154:
5.13 AT+CSCB Select cell broadcast
Page 155 and 156:
5.15 AT+CSMP Set SMS text mode para
Page 157 and 158:
6 GPRS AT commands in accordance wi
Page 159 and 160:
6.1.3 AT+CGDATA Enter data stateTes
Page 161 and 162:
Packet Data Protocol type is a stri
Page 163 and 164:
Parameternumeric PDP Context Identi
Page 165 and 166:
OKat+cgqmin=1,1OKat+cgqmin?+CGQMIN:
Page 167 and 168:
numeric parameter for the precedenc
Page 169 and 170:
at+cgqreq=1,1OKat+cgqreq?+CGQREQ:1,
Page 171 and 172:
6.1.8 AT^SGAUTH Set type of authent
Page 173 and 174:
6.3.1 ATD *98# Request GPRS IP serv
Page 175 and 176:
6.4 Using GPRS AT commands (example
Page 177 and 178:
6.5 Using the GPRS dial command ATD
Page 179 and 180:
7.1 AT^SSTA Remote-SAT Interface Ac
Page 181 and 182:
7.3 AT^SSTGI Remote-SAT Get Informa
Page 183 and 184:
8 APPENDIX8.1 Summary of ERRORS and
Page 185 and 186:
8.1.3 Summary of CMS ERRORS related
Page 187 and 188:
Example 2The application tries to s
Page 189 and 190:
Message Meaning How to activateURC+
Page 191 and 192:
8.1.5 Result codesIndication Numeri
Page 193 and 194:
8.1.9 GSM release cause for Mobilit
Page 195 and 196:
Number Description50 Requested faci
Page 197 and 198:
Number Description309 Linked Respon
Page 199 and 200:
8.1.19 SIEMENS release cause for Em
Page 201 and 202:
AT commandRequired PINAT+CR PIN 1AT
Page 203 and 204:
AT command Test Read Write / NoteEx
Page 205:
*# code Functionality Possible resp
show all

AT Command Set - Olitec

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?