FLEX I/O and FLEX Integra

More documents

Recommendations

Info

148 Power Supply Module Cat. No. 1794-PS13 FLEX I/O and FLEX Integra Product DataPower Supply Module Cat. No. 1794-PS13Example of Using a 1794-PS13 Power Supply toPower Four Adapter ModulesPowerSupplyAdapterPower24V DCPOWER SUPPLY1794-PS1324V dcAll dc powered I/O modules24V dc from separate sourceAHAdapterBCOMI24V dcacAll ac powered I/O modulesCJWiring24VF E D G4015224V dcAdapteracAll ac powered I/O modulesATTENTION!The 1794-PS13 power supply provides sufficient24V dc power to operate up to 4 adaptermodules. Do not attempt to operate an entireFLEX I/O system with this power supply.Terminals A, B, and C are 120/230V supply terminals. Terminals D, E,and F are available to daisychain this 120/230V power to other1794-PS13 power supplies. If supplying 120V ac to the power supply,you can also power the ac modules in the adjacent system.24V dcAdapter120V ac24V dc from separate sourceCombination ac and dc powered I/O modules401531. Connect the 120/230V ac power to the left side terminals onthe connectors on the left side of the module as follows:ConnectToac Ground GND A120/230V ac common L2/N B120/230V ac power L1 C2. Connect terminal G (+24V dc) to the +24V dc terminal on thefirst adapter.3. Connect terminal H (+24V dc common) to the +24V dccommon terminal on the first adapter.4. Repeat steps 3 and 4 using terminals I and J for the secondadapter.5. Connections D, E and F are used to pass 120/230V ac powerto adjacent 1794-PS13 power supplies.Publication 1794-2.1 - January 2000
FLEX I/O and FLEX Integra Product Data Power Supply Module Cat. No. 1794-PS13 149Specifications - 1794-PS13This power supply complies with the CE low-voltage directive.Input SpecificationsNominal Supply Voltage 120V ac, 47-63Hz, 0.6A maximum230V ac, 47-63Hz, 0.42A maximumVoltage Range85-265V acInrush Current40A typical, 1 ac cycle @ Vin 265V ac, 55 o CInterruptionOutput voltage will stay within specification wheninput drops out for 1/2 cycle @ 47Hz, 85V ac withmaximum loadOutput SpecificationsNominal Output Voltage +24V dcVoltage Range20.4-27.6V dc (includes noise & 5% ac ripple)Output Current1.3A maximumMinimum Load0mAOutput SurgeSufficient to drive 4 adapters (surge of 23A for 2mseach)Overvoltage Protection Output internally limited to 35V dc. Cycle power toreenergize.Isolation Voltage2500V dc for 1 secondGeneral SpecificationsMountingTerminal Screw TorqueDimensions HxWxDEnvironmental ConditionsOperational TemperatureStorage TemperatureRelative HumidityShock OperatingNon-operatingVibrationConductors Wire SizeCategoryPublicationInstallation Instructions 1794-5.69Agency CertificationHorizontal or vertical on a DIN rail, wall or panel5-7 lb-in87mm x 68mm x 69mm (3.4in x 2.7in x 2.7in)0 to 55 o C (32 to 131 o F)-40 to 85 o C (-40 to 185 o F)5 to 95% noncondensing30g peak acceleration, 11(±1)ms pulse width50g peak acceleration, 11(±1)ms pulse widthTested 5g @ 10-500Hz per IEC 68-2-612 gauge (4mm 2 ) stranded maximum3/64 inch (1.2mm) insulation maximum1 11 Use this conductor category information for planning conductor routing. Refer topublication 1770-4.1, “Industrial Automation Wiring and Grounding Guidelines forNoise Immunity.”Publication 1794-2.1 - January 2000
Page 7 and 8:
FLEX I/O and FLEX Integra Product D
Page 9:
Page 13 and 14:
Page 16:
16 FLEX I/O Terminal Base Unit’s
Page 20 and 21:
20 3-Wire Screw Clamp Terminal Base
Page 22 and 23:
22 Screw Clamp Temperature Terminal
Page 26 and 27:
26 Terminal Base Unit Cat. No. 1794
Page 28 and 29:
28 1794-TBN and -TBNF Wiring FLEX I
Page 30 and 31:
30 AC Module’s Table of Contents
Page 32 and 33:
32 120V ac 8 Input Module Cat. No.
Page 34 and 35:
34 120V ac 8 Isolated Input Module
Page 36 and 37:
Page 38 and 39:
38 120V ac 8 Output Module Cat. No.
Page 40 and 41:
40 120V ac 8 Output Isolated Module
Page 42 and 43:
42 120V ac 16 Output Module Cat. No
Page 44 and 45:
Page 46 and 47:
46 220V ac 8 Output Module Cat. No.
Page 48 and 49:
48 DC Module’s Table of Contents
Page 50:
50 DC Module’s Recommended Termin
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98: FLEX I/O and FLEX Integra Product D
Page 147: FLEX I/O and FLEX Integra Product D
show all

FLEX I/O and FLEX Integra

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?