PENTAGRAM Cerberus [P 6367] Installation and Operation Manual

More documents

Recommendations

Info

PENTAGRAM Cerberus [P 6367]Reset OOB: Press this button, the WPS client will be in idle state, and WPS indicator will turn off.AP will not respond to the WPS client’s connection requests.WDS SettingsWireless AP signal coverage has range limits. WDS is mainly used to repeat wireless signal, andenlarge its coverage. Please keep SSID, channel and encryption type of all AP respectivelyconsistent.This router supports three WDS modes: Lazy, Bridge, Repeater.• Lazy: In this mode, the connected router must be in Bridge or Repeater mode and the MACaddress of your router must be entered.• Bridge: In this mode, the connected router must be in Lazy or Repeater mode. Manually addthe MAC address of the connected router to AP MAC address list or scan to select.• Repeater: In this mode, the connected router can be in Lazy, Bridge mode or single client.Manually add the MAC address of the connected router to AP MAC address list or scan toselect.Access ControlTo secure your wireless LAN, the wireless access control is actually based on the MAC addressmanagement to allow or block the specific clients to access the wireless network.MAC Address Filter:• Allow: to only allow the clients in the list to access the wireless network.• Block: to only prevent the clients in the list from accessing the wireless network.MAC Address Management: Input the MAC addresses of the wireless clients you want to allow or32
PENTAGRAM Cerberus [P 6367]block and click Add.MAC Address list: Show the added MAC addresses. You can add or delete them.Connection StatusThis page displays wireless client’s connection status, including MAC address, rate, etc.MAC Address: Shows the wireless MAC addresses of the hosts connected to the Router.Bandwidth: Shows the channel bandwidth current connected host (the wireless client) use.DHCP Server [3G Router, WISP or Wireless Router Mode]DHCP ServerDHCP server is to configure TCP/IP parameters for all the computers in LAN. When you enablethe router’s DHCP server, the DHCP server will automatically configure the TCP/IP protocol forall the computers in LAN (including IP address, subnet mask, gateway, DNS, etc.).DHCP Server: Enable or disable DHCP server to automatically assign IP addresses.IP Address Start: Starting IP addresses automatically distributed by DHCP server.IP Address End: Ending IP addresses automatically distributed by DHCP server.Lease Time: The length of the IP address lease.33
Page 1: ENInstallation and Operation Manual
Page 6 and 7: PENTAGRAM Cerberus [P 6367]Router w
Page 8 and 9: PENTAGRAM Cerberus [P 6367]Operatin
Page 10 and 11: PENTAGRAM Cerberus [P 6367]Connecti
Page 12 and 13: PENTAGRAM Cerberus [P 6367]Windows
Page 14 and 15: PENTAGRAM Cerberus [P 6367]Configur
Page 16 and 17: PENTAGRAM Cerberus [P 6367]Setup Wi
Page 18 and 19: PENTAGRAM Cerberus [P 6367]Wireless
Page 20 and 21: PENTAGRAM Cerberus [P 6367]WAN Sett
Page 22 and 23: PENTAGRAM Cerberus [P 6367]ADSL Vir
Page 24 and 25: PENTAGRAM Cerberus [P 6367]DNS Sett
Page 26 and 27: PENTAGRAM Cerberus [P 6367]BSSID: B
Page 28 and 29: PENTAGRAM Cerberus [P 6367]WPA2-Per
Page 30 and 31: PENTAGRAM Cerberus [P 6367]Advanced
Page 34 and 35: PENTAGRAM Cerberus [P 6367]DHCP Lis
Page 36 and 37: PENTAGRAM Cerberus [P 6367]DMZ Sett
Page 38 and 39: PENTAGRAM Cerberus [P 6367]Traffic
Page 40 and 41: PENTAGRAM Cerberus [P 6367]URL Filt
Page 42 and 43: PENTAGRAM Cerberus [P 6367]Remote W
Page 44 and 45: PENTAGRAM Cerberus [P 6367]DDNS [3G
Page 46 and 47: PENTAGRAM Cerberus [P 6367]Change P
Page 48: PENTAGRAM Cerberus [P 6367]NOTES48

PENTAGRAM Cerberus [P 6367] Installation and Operation Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?