Grundoram Manual (PDF 1.7MB) - TT Technologies Inc.

More documents

Recommendations

Info

FIG. 88: PLACE CARRIER CONEON TOOLFIG. 89: INSTALL TWO RINGS INGROOVE OF TOOL BODYFIG. 90: POSITION CARRIER CONEFIG. 91: ATTACH DRAW RODS40 TT TECHNOLOGIES, INC.FIG. 92: INSTALL THRUST PIECEFIG. 93: INSTALL HYDRAULICCYLINDER8. Place carrier cone of the clamping device on the PCG GRUNDORAM tool(see Fig. 88).9. Install the two rings into the groove of the tool body (see Fig. 89).10. Position the carrier cone on top the the two rings (see Fig. 90).11. Attach the three draw rods by screwing them into the carrier cone (see Fig. 91).12. Slide the clamping plate onto the three draw rods, screw the nuts evenly ontothe draw rods to ensure the clamping plate is parallel to the end of the machinebody. Install the thrust piece (see Fig. 92).
13. Insert the hydraulic cylinder and ensure that the bottom of the cylinder is on theclamping plate, then connect the hoses of the hydraulic pump (see Fig. 93).14. Operate the hydraulic cylinder using the manually operated pump (see Fig. 94)until the complete segment ring can be removed.15. Removal of the components of the segment ring (see Fig. 95)NOTE: Do not touch segment grooves with hand. The hydraulic press may fail.Use tools to remove stuck segments.16. Remove the hydraulic cylinder, the clamping plate and the three draw rods(see Fig. 96).17. Remove the complete control stud (see Fig. 97).FIG. 94: OPERATE HAND PUMPFIG. 95: REMOVE SEGMENT RINGFIG. 96: REMOVE HYDRAULICCYLINDERFIG. 97: REMOVE CONTROL STUDTT TECHNOLOGIES, INC.41
Page 9 and 10: Technical SpecificationsA. Compress
Page 11 and 12: Safe Operating PracticesA. Work Are
Page 13 and 14: Base for rammerHeight adjustmentAir
Page 15 and 16: G. Tapered Locking Ram ConesThe pur
Page 17 and 18: I. Soil PortThe soil removal cone p
Page 19: FIG. 29: GRADE BORE CUT-AWAY CUTTIN
Page 22 and 23: 8.Spoil RemovalThe following method
Page 24 and 25: 7. The soil should then be blown ou
Page 26 and 27: A. Grundoram DisassemblyNOTE: The f
Page 28 and 29: B. Piston Removal1. Remove the pist
Page 30 and 31: 3. Fit the new control stud seal in
Page 32 and 33: F. Removal and Disassembly of the C
Page 34 and 35: G. Mini-Atlas Piston Removal1. Plac
Page 36 and 37: I. Mini-Atlas Control Stud Assembly
Page 38 and 39: L. Disassembly of PCG GRUNDORAMFIG.
Page 42 and 43: 18. Use the jacking rod to remove t
Page 44 and 45: N. Control Stud Disassembly1. Place
Page 46 and 47: 7. Replace the black o-ring (see Fi
Page 48 and 49: 6. Once the segment ring is install
Page 50 and 51: Troubleshooting Guide10.Observation
Page 52 and 53: 12.APPENDIXAppendixA. Parts List fo
Page 54 and 55: C. Parts List for 130 Mini-AtlasIte
Page 59 and 60: H. Parts List for 260 GigantItem No
Page 61 and 62: J. Parts List for 350 KolossItem No
Page 63 and 64: L. Parts List for 600 TaurusItem No

Grundoram Manual (PDF 1.7MB) - TT Technologies Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?