Grundoram Manual (PDF 1.7MB) - TT Technologies Inc.

More documents

Recommendations

Info

N. Control Stud Disassembly1. Place the control stud into the TT Technologies repair stand to hold it in place.Install the disassembly tool onto the control stud (see Fig. 109).2. Insert pin into the disassembly tool (see Fig. 110). Install the cover on thedisassembly tool (see Fig. 111). Tighten the nut of the disassembly tool so thesegment rings can be removed (see Fig. 112). Remove the segment ring(see Fig. 113).3. Loosen the nut so you can remove the disassembly tool cover (see Fig. 114),remove the pin and disassembly tool.FIG. 109: INSTALL DISASSEMBLYTOOLFIG. 110: INSERT PIN INTODISASSEMBLY TOOLFIG. 111: INSTALL COVER ONDISASSEMBLY TOOLFIG. 112: TIGHTEN DISASSEMBLYTOOL44 TT TECHNOLOGIES, INC.FIG. 113: REMOVE SEGMENT RINGFIG. 114: REMOVE DISASSEMBLYTOOL COVER
4. Then remove the seal ring and the elastic block (see Fig. 115).5. Remove the outer control tube section (see Fig. 116). Remove the stop ring (seeFig. 117).6. Replace the inner control tube seal (see Fig. 118). Use a compression clamp toreform the seals (see Fig. 119 & Fig. 120).FIG. 115: REMOVE SEAL RING ANDELASTIC BLOCKFIG. 116: REMOVE OUTERCONTROL TUBEFIG. 117: REMOVE STOP RINGFIG. 118: REPLACE INNERCONTROL TUBE SEALFIG. 119: USE COMPRESSIONCLAMP TO REFORM SEALFIG. 120: USE COMPRESSIONCLAMP TO REFORM SEALTT TECHNOLOGIES, INC.45
Page 9 and 10: Technical SpecificationsA. Compress
Page 11 and 12: Safe Operating PracticesA. Work Are
Page 13 and 14: Base for rammerHeight adjustmentAir
Page 15 and 16: G. Tapered Locking Ram ConesThe pur
Page 17 and 18: I. Soil PortThe soil removal cone p
Page 19: FIG. 29: GRADE BORE CUT-AWAY CUTTIN
Page 22 and 23: 8.Spoil RemovalThe following method
Page 24 and 25: 7. The soil should then be blown ou
Page 26 and 27: A. Grundoram DisassemblyNOTE: The f
Page 28 and 29: B. Piston Removal1. Remove the pist
Page 30 and 31: 3. Fit the new control stud seal in
Page 32 and 33: F. Removal and Disassembly of the C
Page 34 and 35: G. Mini-Atlas Piston Removal1. Plac
Page 36 and 37: I. Mini-Atlas Control Stud Assembly
Page 38 and 39: L. Disassembly of PCG GRUNDORAMFIG.
Page 40 and 41: FIG. 88: PLACE CARRIER CONEON TOOLF
Page 42 and 43: 18. Use the jacking rod to remove t
Page 46 and 47: 7. Replace the black o-ring (see Fi
Page 48 and 49: 6. Once the segment ring is install
Page 50 and 51: Troubleshooting Guide10.Observation
Page 52 and 53: 12.APPENDIXAppendixA. Parts List fo
Page 54 and 55: C. Parts List for 130 Mini-AtlasIte
Page 59 and 60: H. Parts List for 260 GigantItem No
Page 61 and 62: J. Parts List for 350 KolossItem No
Page 63 and 64: L. Parts List for 600 TaurusItem No

Grundoram Manual (PDF 1.7MB) - TT Technologies Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?