Grundoram Manual (PDF 1.7MB) - TT Technologies Inc.

More documents

Recommendations

Info

6. Once the segment ring is installed, loosen the nut to remove the disassemblytool, remove the cover, the pin and the disassembly tool. Remove the controlstud from the TT Technologies repair stand and install the control stud into themachine (see Fig. 130).7. Attach the three draw rods by screwing them into the carrier cone. Slide theclamping plate onto the three draw rods, screw the nuts evenly onto the drawrods to ensure the clamping plate is parallel to the end of the machine body.Install the thrust piece. Insert the hydraulic cylinder and ensure that the bottomof the cylinder is on the clamping plate, then connect the hoses of the hydraulicpump. Operate the hydraulic cylinder using the manually operated pump untilthe segment ring can be installed (see Fig. 131).FIG. 130: INSTALL CONTROL STUDFIG. 131: INSTALL SEGMENT RING8. Release the pressure on the hydraulic pump so you can remove the hydraulicpump, thrust piece, clamping plate, three draw rods carrier cone and two rings ingroove of tool body.9. Attach hose connection to tool with three set screws (see Fig. 132). Tighten setscrews, replace cable into the groove of the tool, then attach connection air hose.FIG. 132: INSTALL SET SCREWS10. Specifications of the air hoses. If spare parts are required, use original spareparts for the TT companies or approved agents. The same applies to air hoses.According to the regulations, only use compressed air hoses with a minimumsafe working pressure of 145 psi.48 TT TECHNOLOGIES, INC.
11. Function test. After assembly, check the GRUNDORAM (i.e. lay GRUNDORAMon the ground and connect it to the compressor). Open the air valve slowly andcheck if the piston reciprocates freely. Allow GRUNDORAM, operating atreduced pressure, to run in all new seals, etc., for a few minutes.12. Remarks about the oil to be used. GRUNDO-OIL is a synthetic lubricatewith very good lubrication properties. It is odorless, non-toxic and virtuallyinflammable. GRUNDO-OIL is not harmful to synthetic materials and iscompletely biodegradable. GRUNDO-OIL is water-soluble and has anti-freezeproperties. Should you wish to use another type of oil, we recommend onlypneumatic lubricants with similar properties.TT TECHNOLOGIES, INC.49
Page 9 and 10: Technical SpecificationsA. Compress
Page 11 and 12: Safe Operating PracticesA. Work Are
Page 13 and 14: Base for rammerHeight adjustmentAir
Page 15 and 16: G. Tapered Locking Ram ConesThe pur
Page 17 and 18: I. Soil PortThe soil removal cone p
Page 19: FIG. 29: GRADE BORE CUT-AWAY CUTTIN
Page 22 and 23: 8.Spoil RemovalThe following method
Page 24 and 25: 7. The soil should then be blown ou
Page 26 and 27: A. Grundoram DisassemblyNOTE: The f
Page 28 and 29: B. Piston Removal1. Remove the pist
Page 30 and 31: 3. Fit the new control stud seal in
Page 32 and 33: F. Removal and Disassembly of the C
Page 34 and 35: G. Mini-Atlas Piston Removal1. Plac
Page 36 and 37: I. Mini-Atlas Control Stud Assembly
Page 38 and 39: L. Disassembly of PCG GRUNDORAMFIG.
Page 40 and 41: FIG. 88: PLACE CARRIER CONEON TOOLF
Page 42 and 43: 18. Use the jacking rod to remove t
Page 44 and 45: N. Control Stud Disassembly1. Place
Page 46 and 47: 7. Replace the black o-ring (see Fi
Page 50 and 51: Troubleshooting Guide10.Observation
Page 52 and 53: 12.APPENDIXAppendixA. Parts List fo
Page 54 and 55: C. Parts List for 130 Mini-AtlasIte
Page 59 and 60: H. Parts List for 260 GigantItem No
Page 61 and 62: J. Parts List for 350 KolossItem No
Page 63 and 64: L. Parts List for 600 TaurusItem No

Grundoram Manual (PDF 1.7MB) - TT Technologies Inc.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?