Section 05: Automatic Tool Changers - FadalCNC.com

More documents

Recommendations

Info

FadalMaintenance Manual12) Adjust the air flow. Make sure that the ATC doesn’t move too quickly or tooslowly on a tool change.13) Adjust the cushion. Make sure that during the tool change the ATC doesn’t“bang” at either end of it’s travel.Tool TurretRotationalAdjustment!1) Position the Z-axis to the machine zero.2) Orient the spindle using M19 from MDI mode.IMPORTANTFor Servo Turret, do not adjust the rotation until the turret has been movedby pressing TURRET CW, and then pressing TURRET CCW.3) Loosen each of the six 3/8" hex bolts on the under side of the tool carrier.Figure 5-7 Loosen Hex Bolts on Under Side of Tool Carrier4) With the tool in the spindle, manually move the slide into the spindle, untilfully engaged.Figure 5-8 Manually Move Slide Into Spindle5) Tighten the 6 each 3/8" hex bolts.If the tool carrier does not engage smoothly with the tool in the spindle theremay be a misalignment with orientation assembly.124 Section 05: Automatic Tool Changers March 2003
FadalMaintenance ManualATC Slide BeltReplacement &Adjustment1) Remove ATC upper cover.Figure 5-9 Remove ATC Upper Cover2) Remove tension spring.3) Loosen 4 screws holding motor.Figure 5-10 Loosen Screw that Hold Motor4) Remove belt. Install motor mounting screws.March 2003 Section 05: Automatic Tool Changers 125
Page 1 and 2: FadalMaintenance ManualSection 05:
Page 3 and 4: FadalMaintenance ManualThe motor br
Page 5 and 6: FadalMaintenance ManualATC TURRET F
Page 7 and 8: FadalMaintenance ManualServo Turret
Page 9 and 10: FadalMaintenance ManualFigure 5-2 M
Page 11: FadalMaintenance ManualAdjustthecus
Page 15 and 16: FadalMaintenance Manual9) Install G
Page 17 and 18: FadalMaintenance ManualThe Long and
Page 19 and 20: FadalMaintenance ManualSub-Assembli
Page 21 and 22: FadalMaintenance ManualFigure 5-16
Page 23 and 24: FadalMaintenance ManualInstallation
Page 25 and 26: FadalMaintenance Manual22) If requi
Page 29 and 30: FadalMaintenance Manual4) Type MD,
Page 31 and 32: FadalMaintenance Manual14) Enter th
Page 33 and 34: FadalMaintenance Manual3) Pressing
Page 35 and 36: FadalMaintenance Manual2) Tool Up s
Page 37 and 38: FadalMaintenance Manual12) If the t
Page 39 and 40: FadalMaintenance Manual35) Begin a
Page 41 and 42: FadalMaintenance Manual• Drawbar
Page 43 and 44: FadalMaintenance Manual• SSR for
Page 45 and 46: FadalMaintenance Manual50 Taper Dua
Page 51 and 52: FadalMaintenance ManualInstallation
Page 53 and 54: FadalMaintenance ManualSymptom Poss
Page 55 and 56: FadalMaintenance ManualMaintenance1
Page 57 and 58: FadalMaintenance Manual3) Snugly fa
Page 59 and 60: FadalMaintenance Manual11) Carefull
Page 61 and 62: FadalMaintenance ManualPCB-0213 Dua
Page 63 and 64:
FadalMaintenance ManualCurrentsPeak
Page 65 and 66:
FadalMaintenance ManualSequence of
Page 67 and 68:
FadalMaintenance Manual3) Begin a n
Page 69 and 70:
FadalMaintenance Manualb. Stop the
Page 71 and 72:
FadalMaintenance ManualChanging too
show all

Section 05: Automatic Tool Changers - FadalCNC.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?