Section 05: Automatic Tool Changers - FadalCNC.com

More documents

Recommendations

Info

FadalMaintenance ManualScheduledMaintenanceThe maintenance schedule is based on machine usage of eight hours a day,five days a week.Daily MaintenancePerform the following daily:1) Cleaninga. Remove the chips and debris surrounding the proximity switch inducingblock.b. Remove the chips and debris that have accumulated on the invertedmoving body of the tool pot.c. Clear the tool changing mechanism of all debris before any operation.2) Inspection:a. Check the parts of the tool falling mechanism for damage and wear.Add grease to the sliding base of the tool falling mechanism and thepull rod.b. Check the parts of the tool pots, tool discs, and snap rings for damageand tightness.Weekly MaintenancePerform the following weekly:1) Greasing:a. Grease the claws of the tool changing arm unit.b. Grease the tip of the release pin of the tool changing unit.Miscellaneous MaintenancePerform the following as necessary:1) Change the lubricant annually or as needed. The recommended lubricant isSAE 90-140. The Dual Arm Tool Changer uses approximately 5 liters (1.3gallons).156 Section 05: Automatic Tool Changers March 2003
FadalMaintenance Manual50 Taper Dual ArmTool ChangerTool ChangerSpecificationsType of ToolCAT-50/BT-50Number of Tools 32Maximum Tool DiameterAll Pockets FullØ125mm (4.92in.)Adjacent Pockets Empty Ø250 (9.85in.)Maximum Tool Length Maximum 400mm (15.75in.)Tool Weight Maximum 18kg. (40lb.)Tool Magazine Drive SourceMotor VoltageAC 220 V, 3 PhasesAir Pressure5~7kg/Cm (70-100 psi)March 2003 Section 05: Automatic Tool Changers 157
Page 1 and 2: FadalMaintenance ManualSection 05:
Page 3 and 4: FadalMaintenance ManualThe motor br
Page 5 and 6: FadalMaintenance ManualATC TURRET F
Page 7 and 8: FadalMaintenance ManualServo Turret
Page 9 and 10: FadalMaintenance ManualFigure 5-2 M
Page 11 and 12: FadalMaintenance ManualAdjustthecus
Page 13 and 14: FadalMaintenance ManualATC Slide Be
Page 15 and 16: FadalMaintenance Manual9) Install G
Page 17 and 18: FadalMaintenance ManualThe Long and
Page 19 and 20: FadalMaintenance ManualSub-Assembli
Page 21 and 22: FadalMaintenance ManualFigure 5-16
Page 23 and 24: FadalMaintenance ManualInstallation
Page 25 and 26: FadalMaintenance Manual22) If requi
Page 29 and 30: FadalMaintenance Manual4) Type MD,
Page 31 and 32: FadalMaintenance Manual14) Enter th
Page 33 and 34: FadalMaintenance Manual3) Pressing
Page 35 and 36: FadalMaintenance Manual2) Tool Up s
Page 37 and 38: FadalMaintenance Manual12) If the t
Page 39 and 40: FadalMaintenance Manual35) Begin a
Page 41 and 42: FadalMaintenance Manual• Drawbar
Page 43: FadalMaintenance Manual• SSR for
Page 51 and 52: FadalMaintenance ManualInstallation
Page 53 and 54: FadalMaintenance ManualSymptom Poss
Page 55 and 56: FadalMaintenance ManualMaintenance1
Page 57 and 58: FadalMaintenance Manual3) Snugly fa
Page 59 and 60: FadalMaintenance Manual11) Carefull
Page 61 and 62: FadalMaintenance ManualPCB-0213 Dua
Page 63 and 64: FadalMaintenance ManualCurrentsPeak
Page 65 and 66: FadalMaintenance ManualSequence of
Page 67 and 68: FadalMaintenance Manual3) Begin a n
Page 69 and 70: FadalMaintenance Manualb. Stop the
Page 71 and 72: FadalMaintenance ManualChanging too

Section 05: Automatic Tool Changers - FadalCNC.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?