Section 05: Automatic Tool Changers - FadalCNC.com

More documents

Recommendations

Info

FadalMaintenance ManualAdjustmentsZ Axis Cold StartAdjustmentThere are four motions that influence the automatic tool changer alignment.These motions are:• Z-axis up & down.• Spindle orientation.• Turret in & out.• Turret rotation.1) Remove the ATC upper cover.Figure 5-1 Remove ATC Upper Cover2) Position the Z-axis head to the machine zero position (CS).3) Orientate Spindle (M19).4) Manually move the ATC slide in toward the spindleNote: The EMC machine uses an air cylinder for the turret movement. Tomanually move the ATC as suggested in step (4) several steps must betaken:• Disconnect the air to the machine.• Manually move the ATC slide towards the spindle.• Re-connect the air to the machine for added pressure against the spindle.120 Section 05: Automatic Tool Changers March 2003
FadalMaintenance ManualFigure 5-2 Move ATC Slide Toward Spindle5) Measure the distance from the ATC carriage to the nose of the spindle witha thickness gauge. Adjust the Z axis until the nose of the spindle is .050”[1.27mm] above the turret carriage for CAT taper, .250” [6.35mm] for BTtooling.Figure 5-3 Measure Distance from ATC Carriage to Spindle6) To adjust DC machines, loosen the screw holding the resolver and rotatethe resolver. When the Z axis is in the correct position, tighten the screws.For AC machines, determine their offset by cold starting the machine thenjogging the Z axis. Enter the value in SV.7) Cold Start the machine and recheck the position.March 2003 Section 05: Automatic Tool Changers 121
Page 1 and 2: FadalMaintenance ManualSection 05:
Page 3 and 4: FadalMaintenance ManualThe motor br
Page 5 and 6: FadalMaintenance ManualATC TURRET F
Page 7: FadalMaintenance ManualServo Turret
Page 11 and 12: FadalMaintenance ManualAdjustthecus
Page 13 and 14: FadalMaintenance ManualATC Slide Be
Page 15 and 16: FadalMaintenance Manual9) Install G
Page 17 and 18: FadalMaintenance ManualThe Long and
Page 19 and 20: FadalMaintenance ManualSub-Assembli
Page 21 and 22: FadalMaintenance ManualFigure 5-16
Page 23 and 24: FadalMaintenance ManualInstallation
Page 25 and 26: FadalMaintenance Manual22) If requi
Page 29 and 30: FadalMaintenance Manual4) Type MD,
Page 31 and 32: FadalMaintenance Manual14) Enter th
Page 33 and 34: FadalMaintenance Manual3) Pressing
Page 35 and 36: FadalMaintenance Manual2) Tool Up s
Page 37 and 38: FadalMaintenance Manual12) If the t
Page 39 and 40: FadalMaintenance Manual35) Begin a
Page 41 and 42: FadalMaintenance Manual• Drawbar
Page 43 and 44: FadalMaintenance Manual• SSR for
Page 45 and 46: FadalMaintenance Manual50 Taper Dua
Page 51 and 52: FadalMaintenance ManualInstallation
Page 53 and 54: FadalMaintenance ManualSymptom Poss
Page 55 and 56: FadalMaintenance ManualMaintenance1
Page 57 and 58: FadalMaintenance Manual3) Snugly fa
Page 59 and 60:
FadalMaintenance Manual11) Carefull
Page 61 and 62:
FadalMaintenance ManualPCB-0213 Dua
Page 63 and 64:
FadalMaintenance ManualCurrentsPeak
Page 65 and 66:
FadalMaintenance ManualSequence of
Page 67 and 68:
FadalMaintenance Manual3) Begin a n
Page 69 and 70:
FadalMaintenance Manualb. Stop the
Page 71 and 72:
FadalMaintenance ManualChanging too
show all

Section 05: Automatic Tool Changers - FadalCNC.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?