Section 05: Automatic Tool Changers - FadalCNC.com

More documents

Recommendations

Info

FadalMaintenance Manual8) Remove slide motor.9) Install replacement slide motor.10) Re-install motor mounting plate.11) Connect the Molex motor connector.12) Install belt. (see belt replacement procedure)13) Install tension spring.14) Perform alignment procedures.15) Replace covers.Turret Factor SettingThis parameter is set at the factory. This parameter should not be changedunless the turret motor has been replaced or the tool turret rotation is over orunder shooting.Note: VMCs equipped with the Servo Turret ATC, instead of the Geneva-drivenATC, must ALWAYS have a turret factor of 1.A proper turret factor will have the Geneva driver positioned as in Figure 5-11-a.An incorrect turret factor will have the Geneva driver positioned approximately asshown in Figure 5-11-bFigure 5-12 -a Correct GenevaadjustmentFigure 5-11-b Incorrect GenevaadjustmentPulley AlignmentFadal Spindle Pulleys have lines for the orientation alignment of the spindle. Toachieve proper alignment, the line on the top of the spindle must be alignedwith one of the three lines on the spindle pulley.• The Long Line, which is for all Machines except for VMC 4020 with 30tool ATC, and the Dual Arm ATC.• The Short Line, which is for VMC 4020 machines with 30 tool ATC.128 Section 05: Automatic Tool Changers March 2003
FadalMaintenance ManualThe Long and Short Lines are next to one another.• The new pulleys will also have a Third Line, which is for the Dual ArmATC.Figure 5-13 Fadal Spindle PulleysMarch 2003 Section 05: Automatic Tool Changers 129
Page 1 and 2: FadalMaintenance ManualSection 05:
Page 3 and 4: FadalMaintenance ManualThe motor br
Page 5 and 6: FadalMaintenance ManualATC TURRET F
Page 7 and 8: FadalMaintenance ManualServo Turret
Page 9 and 10: FadalMaintenance ManualFigure 5-2 M
Page 11 and 12: FadalMaintenance ManualAdjustthecus
Page 13 and 14: FadalMaintenance ManualATC Slide Be
Page 15: FadalMaintenance Manual9) Install G
Page 19 and 20: FadalMaintenance ManualSub-Assembli
Page 21 and 22: FadalMaintenance ManualFigure 5-16
Page 23 and 24: FadalMaintenance ManualInstallation
Page 25 and 26: FadalMaintenance Manual22) If requi
Page 29 and 30: FadalMaintenance Manual4) Type MD,
Page 31 and 32: FadalMaintenance Manual14) Enter th
Page 33 and 34: FadalMaintenance Manual3) Pressing
Page 35 and 36: FadalMaintenance Manual2) Tool Up s
Page 37 and 38: FadalMaintenance Manual12) If the t
Page 39 and 40: FadalMaintenance Manual35) Begin a
Page 41 and 42: FadalMaintenance Manual• Drawbar
Page 43 and 44: FadalMaintenance Manual• SSR for
Page 45 and 46: FadalMaintenance Manual50 Taper Dua
Page 51 and 52: FadalMaintenance ManualInstallation
Page 53 and 54: FadalMaintenance ManualSymptom Poss
Page 55 and 56: FadalMaintenance ManualMaintenance1
Page 57 and 58: FadalMaintenance Manual3) Snugly fa
Page 59 and 60: FadalMaintenance Manual11) Carefull
Page 61 and 62: FadalMaintenance ManualPCB-0213 Dua
Page 63 and 64: FadalMaintenance ManualCurrentsPeak
Page 65 and 66: FadalMaintenance ManualSequence of
Page 67 and 68:
FadalMaintenance Manual3) Begin a n
Page 69 and 70:
FadalMaintenance Manualb. Stop the
Page 71 and 72:
FadalMaintenance ManualChanging too
show all

Section 05: Automatic Tool Changers - FadalCNC.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?