Section 05: Automatic Tool Changers - FadalCNC.com

More documents

Recommendations

Info

FadalMaintenance Manual30) While rotating the ATC arm, pull the motor brake switch up. This is theelectromagnetic brake that will be holding the motor back from turningsmoothly. The switch is located on top and to the front of the ATC motor(the switch must be held up). See Figure 5-18, position 3. When the motorhas reached the lowest position, press the plunger and remove the toolholder.31) Start turning the ATC motor again, in the same direction as in step #30. Thefalling mechanism will reverse, sending the arm back up. At the highestposition, the arm body will turn back (80 degrees for the 3020, 65 degreesfor the 4525 and 35 degrees for the 6535) to the stand by position 1 (ATCHome Position).32) Remove the spindle fixture from the head.Figure 5-18 Manual Rotation of Tool ArmFigure 5-19 Pull Motor Brake Switch138 Section 05: Automatic Tool Changers March 2003
FadalMaintenance ManualFigure 5-20 ATC MovementMarch 2003 Section 05: Automatic Tool Changers 139
Page 1 and 2: FadalMaintenance ManualSection 05:
Page 3 and 4: FadalMaintenance ManualThe motor br
Page 5 and 6: FadalMaintenance ManualATC TURRET F
Page 7 and 8: FadalMaintenance ManualServo Turret
Page 9 and 10: FadalMaintenance ManualFigure 5-2 M
Page 11 and 12: FadalMaintenance ManualAdjustthecus
Page 13 and 14: FadalMaintenance ManualATC Slide Be
Page 15 and 16: FadalMaintenance Manual9) Install G
Page 17 and 18: FadalMaintenance ManualThe Long and
Page 19 and 20: FadalMaintenance ManualSub-Assembli
Page 21 and 22: FadalMaintenance ManualFigure 5-16
Page 23 and 24: FadalMaintenance ManualInstallation
Page 25: FadalMaintenance Manual22) If requi
Page 29 and 30: FadalMaintenance Manual4) Type MD,
Page 31 and 32: FadalMaintenance Manual14) Enter th
Page 33 and 34: FadalMaintenance Manual3) Pressing
Page 35 and 36: FadalMaintenance Manual2) Tool Up s
Page 37 and 38: FadalMaintenance Manual12) If the t
Page 39 and 40: FadalMaintenance Manual35) Begin a
Page 41 and 42: FadalMaintenance Manual• Drawbar
Page 43 and 44: FadalMaintenance Manual• SSR for
Page 45 and 46: FadalMaintenance Manual50 Taper Dua
Page 51 and 52: FadalMaintenance ManualInstallation
Page 53 and 54: FadalMaintenance ManualSymptom Poss
Page 55 and 56: FadalMaintenance ManualMaintenance1
Page 57 and 58: FadalMaintenance Manual3) Snugly fa
Page 59 and 60: FadalMaintenance Manual11) Carefull
Page 61 and 62: FadalMaintenance ManualPCB-0213 Dua
Page 63 and 64: FadalMaintenance ManualCurrentsPeak
Page 65 and 66: FadalMaintenance ManualSequence of
Page 67 and 68: FadalMaintenance Manual3) Begin a n
Page 69 and 70: FadalMaintenance Manualb. Stop the
Page 71 and 72: FadalMaintenance ManualChanging too

Section 05: Automatic Tool Changers - FadalCNC.com

Create successful ePaper yourself

Delete template?

Save as template?