Hawk Sport Construction Manual

More documents

Recommendations

Info

STEP STEP 11 11 11 Main Main Main Gear Gear & & Shaft Shaft Shaft Assembly Assembly From parts bag 2: The Main Gear is preassembled with the Auto-Rotation Bearing installed. Insert the bottom end through the auto rotation gear assembly, align the holes and secure the Main Shaft using one 3x16mm Socket Cap Screw and one 3mm Locknut. You can temporarily insert main shaft, main shaft bearing spacer & bearing, stopper and head block screw to keep them from getting lost! * Do not apply threadlock here. * 10 Completed Main Gear & Main Shaft STEP STEP 12 12 Elevator Elevator Lever Lever Assembly Assembly From parts bag 2: Insert the long threaded axle and one M3x7 ball bearing from each end of the bellcrank. Slide one short spacer over one 3x30mm Socket Cap screw and attach to the threaded axle ( do do not not not use use threadlock threadlock here! here! here!), here! repeat for other side. The 2x16mm pin is assembled, just insure the elevator radius link moves freely against the Bellcrank. Thread one short steel ball into the elevator arm. CNQSC04 Optional machined ball bearing elevator arm w/ adjustable ball link. Elevator Bellcrank [HI3032B] Auto- Rotation Bearing [HW3050] Pre- Assembled M3 Locknut Elevator Link Only [HI3032C] M2x16 Pin Short Steel Ball M2 [CNLR1013] Short Spacer x 2 M3x16 Socket Cap Screw Only assemble, do not use threadlock now! Main Shaft [HW3053A] Main Gear [HI3056] Long Threaded Axle M3x7 Ball Bearing x 2 [CNBB0730] M3x30 Socket Cap Screw X 2
STEP STEP 13 13 13 Upper Upper Side Side Side Frames Frames From parts bag 2: Install two M4x5 Set Screws (note-do note-do not not apply apply apply locktite locktite at at at this this time time) time into the Mast Stopper (note note that that the the the raised raised raised inner inner inner diameter diameter diameter must must must face face face the the the ball ball ball bearing) bearing) bearing) and slide the mast stopper on the main shaft followed by one M10x19 Ball Bearing and one M14x19 Spacer (the the spacer spacer must must be be installed installed on on on top top top of of of the the the bearing). bearing bearing Slide one M8x19 Ball Bearing from the bottom of the main shaft. Attach the starter shaft assembly to the left side upper side frame with four M3x12 Self Tapping Screws (Tip Tip 2 22- 2 observe observe the the correct correct correct orientation orientation orientation of of of the the the block block block assemblies). assemblies assemblies Position the main gear/ main shaft assembly, (note note the the the orientation orientation of of the the mast mast stopper, stopper, the the the raised raised inner inner diameter diameter should should be be facing facing facing upward, upward, upward, towards towards towards the the the inner inner inner race race race of of of the the the top top top bearing) bearing bearing the counter gear assembly and the tail transmission output shaft assembly in their designated locations (see diagram below) on the upper right side frame (make make make sure sure the the bearings bearings are are are fully fully seated seated in in the the recesses recesses). recesses M3x12 Self Tapping Screws x 4 3 3 Start Shaft Assembly from Step 8 Upper Side Frame [HI3107] Counter Gear Assembly from Step 10 Tail Transmission Output Gear Assembly from Step 9 M19x14 Spacer [HI3107A] Mast Stopper [HW3054A] M8x19 Ball Bearing [CNBB1980] M10x19 Ball Bearing [CNBB1019] M4x4 Set Screw (med hex key) x 2 1 Main Gear Assembly from Step 11 Be Be careful careful when when tightening tightening the the eight eight 3x12mm 3x12mm self self tapping tapping screws screws screws into into the the start start shaft shaft block block assemblies assemblies as as excessive excessive force force can can can strip strip the the plastic plastic holes. holes. 11
Page 1 and 2: Hawk Sport Instruction Manual SPECI
Page 3 and 4: 6 Channel Helicopter Radio or Equiv
Page 5 and 6: STEP STEP 1 1 Main Main Rotor Rotor
Page 7 and 8: STEP STEP STEP 5 5 Flybar, Flybar,
Page 9: STEP STEP 9 9 Tail Tail Transmissio
Page 13 and 14: STEP STEP 15 15 Collective Collecti
Page 15 and 16: STEP STEP 18 18 Fuel Fuel Tank Tank
Page 17 and 18: STEP STEP 22 22 22 Final Final Roto
Page 19 and 20: STEP STEP 26 26 Landing Landing Lan
Page 21 and 22: STEP STEP 31 31 Tail Tail Rotor Rot
Page 23 and 24: STEP STEP 35 35 Tail Tail Gearbox G
Page 25 and 26: STEP STEP 38 38 Pushrod Pushrod Set
Page 27 and 28: STEP STEP 41 41 Aileron Aileron & &
Page 29 and 30: STEP STEP 43 43 Rudder Rudder Linka
Page 31 and 32: Step Step 46 46 Canopy Canopy & & D
Page 33 and 34: The connectors on the gyro have bee
Page 35 and 36: -2 Pitch Curve Hovering - ( linear
Page 37 and 38: Before Flying your Hawk Sport Helic
Page 39 and 40: Hovering Hovering Hovering When all
Page 41 and 42: Hawk Sport Replacement Parts HW3000
Page 43 and 44: Fiber Fiber Glass Glass Whip Whip A

Hawk Sport Construction Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?