Hawk Sport Construction Manual

More documents

Recommendations

Info

STEP STEP 36 36 Attach Attach Tailboom Tailboom to to Mechanics Mechanics Attach the tail boom assembly to the main mechanics by sliding the tailboom tube into the mounting hole at the rear of the upper frame using five M3x25 Socket Cap Screws and M3 Locknuts. Slowly press the tailboom in, being careful to engage the flattened end of the drive wire into the slotted tail rotor output gear shaft. The slots on the end of the tailboom will self align with molded pins inside the upper side frame. Take your time and the wire will slide in. Once engaged, press the tail boom in completely until it is fully seated. Hold the maingear from moving and try to turn the tail rotor to insure proper engagement, you should not be able to turn the tail rotor. If you can rotate it, the drive wire is probably not properly seated into the slot in the front output shaft. Connect the short rudder pushrod to the coupler at this time. 24 M3 Locknut x 5 Main Mechanics STEP STEP 37 37 Horizontal Horizontal Fin Fin & & Tail Tail Tail Boom Boom Struts Struts Position the horizontal fin with two pushrod guides ahead and one pushrod guide behind. Insert two M3x12 Self Tapping Screws through the Horizontal Fin, then the horizontal fin mount and finally into the tailboom clamp capturing the tailboom. Position the fin along the tailboom at the position where the Tail Boom support struts can be attached. Secure the support struts to the fin mount with a M3x8 Self Tapping Screws. Attach the front of the two support struts to the lower frame assembly using two M3x16 Socket Cap Screws, M3x9 Spacer and M3 locknut. Verify the long tail rotor control pushrod is inserted through the fin clamp and the three guides along the tailboom. M3 locknut x 2 M3x25 Socket Cap Screws x 5 Horizontal Fin, Fin Mount & Tail Boom Clamp Set [HI3067A] Spacer M3x9 x2 Tail Boom Assembly M3x12 Self Tapping Screw x 2 Tail Boom Support Struts [HW3202B ] M3x16 Socket Cap Screws x 2 M3x8 Self Tapping Screw x 2
STEP STEP 38 38 Pushrod Pushrod Setup Setup and and Adjustments Adjustments All the control pushrods are pre-assembled. All that is left is fine tuning of the length depending on the flying style before the pushrods can be attached. Carefully look at the plastic ball ends, press the ball link over the steel ball with the “Century” name visible, this is the correct installation direction. It is very important that before you install the pushrod linkages that you first charge your radio then remove all the servo horns from the servos and center all the mechanical or electronic trims on the radio. Note: All dimensions are in millimeters and are measured from the centers of the control balls. Ball Link Set [HI3145] J A I G B C D E F Pushrod Set [HW3192] Due to the different type of radio and servos that are chosen to install in to the helicopter, match each pushrod to the lengths in the table for optimum setup. Drawing is not to scale, use measurements in table. Location Pushrod <strong>Sport</strong> 3D Washout to flybar (2) A 44 47 Throttle servo B 96 96 Bell mixer to SWP (2) C 97 99 Collective servo D 95 93 Elevator servo E 128 128 Aileron servo (2) F 151 151 Bell mixer to seesaw (2) I 28 26 Ail. Bellcrank to SWP (2) J 54 54 Tail rotor pushrod G 887 887 (Optional Part) CN2255 Control Rod Setup Gauge - Easily duplicate pushrods by attaching a master pushrod and match new pushrods as they are assembled. Gauge has millimeter scale for accurate lengths center to center. Tail Pitch Control Rod & Connector [HW3064C] 25
Page 1 and 2: Hawk Sport Instruction Manual SPECI
Page 3 and 4: 6 Channel Helicopter Radio or Equiv
Page 5 and 6: STEP STEP 1 1 Main Main Rotor Rotor
Page 7 and 8: STEP STEP STEP 5 5 Flybar, Flybar,
Page 9 and 10: STEP STEP 9 9 Tail Tail Transmissio
Page 11 and 12: STEP STEP 13 13 13 Upper Upper Side
Page 13 and 14: STEP STEP 15 15 Collective Collecti
Page 15 and 16: STEP STEP 18 18 Fuel Fuel Tank Tank
Page 17 and 18: STEP STEP 22 22 22 Final Final Roto
Page 19 and 20: STEP STEP 26 26 Landing Landing Lan
Page 21 and 22: STEP STEP 31 31 Tail Tail Rotor Rot
Page 23: STEP STEP 35 35 Tail Tail Gearbox G
Page 27 and 28: STEP STEP 41 41 Aileron Aileron & &
Page 29 and 30: STEP STEP 43 43 Rudder Rudder Linka
Page 31 and 32: Step Step 46 46 Canopy Canopy & & D
Page 33 and 34: The connectors on the gyro have bee
Page 35 and 36: -2 Pitch Curve Hovering - ( linear
Page 37 and 38: Before Flying your Hawk Sport Helic
Page 39 and 40: Hovering Hovering Hovering When all
Page 41 and 42: Hawk Sport Replacement Parts HW3000
Page 43 and 44: Fiber Fiber Glass Glass Whip Whip A

Hawk Sport Construction Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?