Hawk Sport Construction Manual

More documents

Recommendations

Info

2 Table Table of of Contents Contents Contents Table of Contents & Introduction ...................................................................................................................... 1-2 Required Items and Building Guide for Assembly .......................................................................................... 3-4 Main Rotor Head, Washout & Swashplate Assembly Steps 1-6 ........................................... 5-7 Start Shaft Assembly & Drive Train Assembly Steps 7-12 ....................................... 8-10 Upper Side Frame Assembly Steps 13-15 ................................... 11-13 Clutch, Clutch Bell, Fan, Shroud & Engine Mount Steps 16-17 ......................................... 14 Fuel Tank & Lower Frames Assembly Step 18-21 .................................... 15-16 Final Rotor Head Assembly, Muffler & Servo Frames Step 22-25 .................................... 17-18 Landing Gear Step 26 ................................................ 19 Tail Rotor Assembly Step 27-37 .................................... 19-24 Pushrod, Radio & Servo Setup Step 38-44 .................................... 25-30 Main Blades & Canopy Step 45-47 .................................... 30-31 Radio Components & Balancing .......................................................................................................................... 32 Setup and Installation of PG-2000 II Gyro ........................................................................................................ 33 Radio Setup, Pitch,Throttle and Tail Rotor Curve Setup .......................................................................... 34-36 Before Flying, Starting the Engine & Basic Hovering ............................................................................... 37-39 Replacement Parts List & Parts Photos........................................................................................................ 40-44 Introduction Introduction Congratulations on your purchase of Century Helicopter Product's latest version of our HAWK series RC helicopter model. The HAWK <strong>Sport</strong> helicopter is not only ideal for beginners new to the hobby, but also for the intermediate right on through to the expert and 3D flyers. A 6 channel helicopter radio is recommended as the bare minimum to take advantage of the helicopter programming included in these radios. The expert to 3D flyers would certainly be using a good 8 to 10 channel helicopter radio. You may wish to check with us or your local dealer for compatible components. Warning Warning This radio controlled model is not a toy! It is a precision machine requiring proper assembly and setup to avoid accidents. It is the responsibility of the owner to operate this product in a safe manner as it can inflict serious injury . It is recommended that if you are in doubt of your abilities, seek assistance from experienced radio control helicopter modelers and associations. As manufacturer, we assume no liability for the use of this product. Pre-assembly Pre-assembly Information Information Information Upon opening the kit, all the major component parts are packaged in numbered bags to correspond to specific sections of the manual, greatly facilitating assembly. Various assemblies have been pre-assembled, only requiring the final assembly and installation of the various sub-assemblies. The screws and nuts required for each step are packaged in the same bag as the parts for that step. Be careful not to lose any of the hardware when opening each bag. Care has been taken in filling and packing of each bag. However mistakes do happen, if there is a parts shortage or any hardware missing, please feel free to contact us at: Century Helicopter Products 523 Sinclair Frontage Road, Milpitas, CA 95035 USA Fax:408-942-9524 web: www.centuryheli.com e-mail: info@centuryheli.com
6 Channel Helicopter Radio or Equivalent. Main Blade Pitch Gauge w/PaddleGauge #CN2026 5.5mm & 7mm nut drivers, Phillips Screw Driver, 3mm & 4mm hex drivers Ball Link Plier #CN2034 Allen Key Set CNBN10946 Necessary Necessary Items Items “Not “Not Included” Included” in in the the kit. kit. PG2000 II dual rate piezo gyro CN2018 (or eqivalent) 32-38 Helicopter Engine Necessary Necessary Tools Tools for for for Assembly Assembly and and Adjustments Adjustments Needle Nose Plier & Cutter Pliers 4 Way Wrench #CN2031 Hobby Scissors Metric Ruler Hobby Knife 15% or 30% Heli Fuel Whip Antenna Remote Glow Adapter CN2222 *Optional Tune Muffler #CN3033 12Volt Start Battery Fuel Line Glow Driver w/Charger Fuel Filter Glow Plug Tie-Wraps Servo Tape Locktite CN2025B 12Volt Starter Eletric or Hand Fuel Pump CN2024T Lubrication 3
Page 1: Hawk Sport Instruction Manual SPECI
Page 5 and 6: STEP STEP 1 1 Main Main Rotor Rotor
Page 7 and 8: STEP STEP STEP 5 5 Flybar, Flybar,
Page 9 and 10: STEP STEP 9 9 Tail Tail Transmissio
Page 11 and 12: STEP STEP 13 13 13 Upper Upper Side
Page 13 and 14: STEP STEP 15 15 Collective Collecti
Page 15 and 16: STEP STEP 18 18 Fuel Fuel Tank Tank
Page 17 and 18: STEP STEP 22 22 22 Final Final Roto
Page 19 and 20: STEP STEP 26 26 Landing Landing Lan
Page 21 and 22: STEP STEP 31 31 Tail Tail Rotor Rot
Page 23 and 24: STEP STEP 35 35 Tail Tail Gearbox G
Page 25 and 26: STEP STEP 38 38 Pushrod Pushrod Set
Page 27 and 28: STEP STEP 41 41 Aileron Aileron & &
Page 29 and 30: STEP STEP 43 43 Rudder Rudder Linka
Page 31 and 32: Step Step 46 46 Canopy Canopy & & D
Page 33 and 34: The connectors on the gyro have bee
Page 35 and 36: -2 Pitch Curve Hovering - ( linear
Page 37 and 38: Before Flying your Hawk Sport Helic
Page 39 and 40: Hovering Hovering Hovering When all
Page 41 and 42: Hawk Sport Replacement Parts HW3000
Page 43 and 44: Fiber Fiber Glass Glass Whip Whip A

Hawk Sport Construction Manual

Create successful ePaper yourself

Delete template?

Save as template?