Installation Manual - Future Pipe Industries

More documents

Recommendations

Info

Fig. 5.2.j. locking strip insert hole for locking spigot end socket end Tabel 5.c. Admissible angular deflection - Using a plastic hammer or a piece of wood, tap the locking strip home until it rests against the first part of the strip. - The end of the locking strip sticks out by approx. 100 mm. This allows disassembly of the newly assembled joint. - Ensure that the stop of both the socket end and the spigot end are in contact with the locking strip and that the fully extended system is kept in this position. Note: At low temperatures a plastic locking strip may become less flexible. In that case it is advisable to warm the locking strip up to about 20(C. ID Play C Angular deflection (mm) (mm) RSLJ RSJ 80 2.5 1˚30 3˚ 100 3.0 1˚30 3˚ 150 6.0 1˚30 3˚ 200 8.0 1˚30 3˚ 250 9.0 1˚30 3˚ 300 10.0 1˚30 3˚ 350 11.0 1˚30 3˚ 400 13.0 1˚30 3˚ 450 14.0 1˚30 3˚ 500 16.0 1˚30 3˚ 600 19.0 1˚30 2˚ 700 16.0 1˚ 2˚ 750 17.0 1˚ 2˚ 800 19.0 1˚ 2˚ 900 21.0 1˚ 2˚ 1000 23.0 1˚ 2˚ 1200 27.0 1˚ 1˚ For RSJ systems an additional 'end play' of 30 mm is allowed for diameters up to 300 mm and 50 mm for diameters 350 mm up to 1200 mm. This 'end play' allows for contraction as a result of pressure, temperature changes and soil settlements and therefore should not be used in the installation. Wavistrong Installation Manual 20
5.3. Dimensions of the rubber ring and the locking strip The commonly used rubber ring is made of NBR (Nitril Butadiene Rubber). Other types of rubber can be supplied depending on the medium and/or the temperature. The different types of rubber can be recognized by the following codes: S - styrene butadiene rubber SBR colour code red spot N - nitrile butadiene rubber NBR colour code yellow spot E - ethene propene terpolymer EPDM colour code blue spot F - fluor elastomer FKM H - hydrogenated nitrile butadiene rubber H-NBR Fig. 5.3.a. The dimensions d and D are shown on the O-ring as well as the year and month of production Table 5.d. O-rings dimensions d ID (mm) d (mm) D (mm) 80 7 80 100 7 109 150 10 156 200 10 207 250 14 260 300 14 311 350 14 360 400 17 409 450 17 460 500 22 508 600 22 610 700 26 690 750 26 740 800 26 790 900 26 880 1000 26 980 1200 30 1120 Wavistrong Installation Manual 21 D
Page 1 and 2: Wavistrong ® Installation Manual R
Page 3 and 4: Table of Contents 1. Introduction 5
Page 5 and 6: 1. Introduction This manual is writ
Page 7 and 8: 2.2. Unloading The unloading of mat
Page 9 and 10: G Unprotected flange-faces should n
Page 11 and 12: 4. Adhesive bonded joints Before ad
Page 13 and 14: The temperature of the heating blan
Page 15 and 16: 5. Integral Rubber seal joint (RSJ)
Page 17 and 18: Fig. 5.2.d. - Apply Future Pipe Ind
Page 19: 5.2.4. Rubber Seal Lock Joint (RSLJ
Page 23 and 24: 5.4. Installation time for the rubb
Page 25 and 26: 6. Flanged joints Before assembling
Page 27 and 28: Fig. 6.2.e. The flange must be conn
Page 29 and 30: 6.5. Determination of the bolt leng
Page 31 and 32: 7.5. Laminating Grind the surface (
Page 33 and 34: 9. Installation of underground pipe
Page 35 and 36: If the trench wall is of a soil typ
Page 37 and 38: If Wavistrong pipes are installed i
Page 39 and 40: 9.3.1. Other methods of back fillin
Page 41 and 42: 9.5. Relief plates Where pipes are
Page 43 and 44: Using this method of installation r
Page 45 and 46: 10. Installation of above ground pi
Page 47 and 48: Fig. 10.2.b. Support distance When
Page 49 and 50: The choice of a certain clip design
Page 51 and 52: Fig. 10.4.c. Fig. 10.4.d. concrete
Page 53 and 54: 10.6. Connection to other materials
Page 55 and 56: 10.8. UV resistance The topcoat of
Page 57 and 58: 10.10.3. After assembly of the R.T.
Page 59 and 60: 11. Field test procedure Before the
Page 61: 12. Safety precautions The followin

Installation Manual - Future Pipe Industries

Create successful ePaper yourself

Delete template?

Save as template?