standard specification for erection tender - GAIL

More documents

Recommendations

Info

sling so that an even coating is obtained all round the bottom. This work shall be done very carefully and by experienced personnel. There shall not be any formation of "Whiskers" and holes in the coating. The coating film shall be inspected by mirror. 5.7.10 For each coat, the painter should know the WFT corresponding to the specified DFT and standardize the paint application technique to achieve the desired WFT. This has to be ensured in the qualification trial. 5.8 Drying of coated Surfaces 5.8.1 No coat shall be applied until the preceding coat has dried. The material shall be considered dry for re-coating when another coat can be applied without the development of any film irregularities such as lifting or loss of adhesion of undercoats. Drying time of the applied coat should not exceed maximum specified for it as a first coat; if it exceeds the paint material has possibly deteriorated or mixing is faulty. 5.8.2 No paint shall be force dried under conditions which will cause checking, wrinkling, blistering formation of pores, or detrimentally affect the condition of the paint. 5.8.3 No drier shall be added to a paint on the job unless specifically called for in the manufacturer's specification for the paint. 5.8.4 Paint shall be protected from rain, condensation, contamination, snow and freezing until dry to the fullest extent practicable. 5.9 Repair of damaged paint surface 5.9.1 Where paint has been damaged in handling and in transportation, the repair of damaged coating of pre-erection / fabrication shall be as given below. 5.9.2 Repair of damaged inorganic zinc silicate primer after erection / welding: Quickly remove the primer from damaged area by mechanical scraping and emery paper to expose the white metal. Blast clean the surface if possible. Feather the primer over the intact adjacent surface surrounding the damaged area by emery paper. 5.9.3 Repair of damaged pre-erection and shop priming in the design temperature of - 90°C to 500°C. � Surface preparation shall be done as per procedure 5.9.2. � One coat of F-9 shall be applied wherever damaged was observed on preerection / pre-fabrication / shop primer of inorganic zinc silicate coating (F- 9). F-9 shall not be applied if damaged area is not more than 5x5 cm. 5.10 PAINT APPLICATION GAIL (INDIA) LTD NEW DELHI DOCUMENT NO. REV-0 STANDARD SPECIFICATION FOR SHOP AND FIELD PAINTING Page 13 of 49 S-05-02-014 Copyright GAIL – All rights reserved
5.10.1 Shop priming / pre-erection priming with F9 or F12 shall be done only on blasted surface. 5.10.2 Shop priming / pre-erection priming with F9 or F12 shall be done only with airless spray. 5.10.3 For large flat surface field painting shall be done by airless spray otherwise brush can be used. 5.11 Documentation � A written quality plan with procedure for qualification trials and for the actual work. � Daily progress report with details of weather conditions, particular of applications, no of coats and type of materials applied, anomalies, progress of work versus programmed. � Results of measurement of temperatures relative humidity, surface profile, film thickness, holiday detection, adhesion tests with signature of appropriate authority. � Particulars of surface preparation and paint application during trials and during the work. � Details of non-compliance, rejects and repairs. � Type of testing equipments and calibration. � Code and batch numbers of paint materials used. GAIL (INDIA) LTD NEW DELHI DOCUMENT NO. REV-0 STANDARD SPECIFICATION FOR SHOP AND FIELD PAINTING Page 14 of 49 S-05-02-014 Copyright GAIL – All rights reserved
Page 1 and 2:
GAIL (INDIA) LTD NEW DELHI GAIL (In
Page 3 and 4:
ANNEXURE - I CONTRACTOR’S SCOPE O
Page 5 and 6:
1.3 Any activity specifically not l
Page 7 and 8:
converter, barriers, relays, cables
Page 9 and 10:
standards etc. and obtaining all re
Page 11 and 12:
c) Contractor shall prepare purchas
Page 13 and 14:
) The gas custody transfer metering
Page 15 and 16:
q) Platforms & cross over to be pro
Page 17 and 18:
nn) Dual Isolation Valves shall be
Page 19 and 20:
3.2.1 Design and terminology shall
Page 21 and 22:
GAIL (INDIA) LTD NEW DELHI IEC-6033
Page 23 and 24:
Necessary filtration and double sta
Page 25 and 26:
3.3.3.4 All instruments in the unit
Page 27 and 28:
3.4.2.6 Junction boxes (as per the
Page 29 and 30:
Typical gas composition S.N PARAMET
Page 31 and 32:
� Pressure Class of Skid up to PR
Page 33 and 34:
esponsibility for delivering equipm
Page 35 and 36:
principal grain flow and notched pe
Page 37 and 38:
carried out at manufacturer’s wor
Page 39 and 40:
(e) Bubble wrapping as well as tran
Page 41 and 42:
Mandatory Spares: Shall be provided
Page 43 and 44:
application. Type approval certific
Page 45 and 46:
16 Temperature gauges and Thermowel
Page 47 and 48:
24 Standard specification for Inspe
Page 49 and 50:
GAIL (INDIA) LTD NEW DELHI JOB SPEC
Page 51 and 52:
1.0 Introduction 1.1 General 1.2 Sc
Page 53 and 54:
ISO 170125: Calibration of all prim
Page 55 and 56:
separate limit switches for open an
Page 57 and 58:
measurement will not degrade by mor
Page 59 and 60:
computer for custody transfer flow
Page 61 and 62:
l) A statement of uncertainty for t
Page 63 and 64:
The flow computers shall be Micropr
Page 65 and 66:
KEYBOARD CAPABILITY: The data entry
Page 67 and 68:
Energy - Mcal/MMBTU/ MJ (user selec
Page 69 and 70:
LEL detectors/transmitters shall be
Page 71 and 72:
� The control panel shall also ha
Page 73 and 74:
GAIL (INDIA) LTD NEW DELHI ii) Anal
Page 75 and 76:
Metering supervisory system shall b
Page 77 and 78:
egulating the sample pressure & flo
Page 79 and 80:
III. Mole % CO2 IV. Mole % N2 Each
Page 81 and 82:
and ±0.5 % for components (mole%)
Page 83 and 84:
9 Accessories Cell Battery and Char
Page 85 and 86:
S NO. TITLE 1 GENERAL CONTENTS 2 DE
Page 87 and 88:
2.5 Standards 2.5.1 The instrumenta
Page 89 and 90:
3.2.23 Supply of all types of consu
Page 91 and 92:
4.3.1 Multitube/Multicore cables sh
Page 93 and 94:
4.8.4 Cables shall have complete un
Page 95 and 96:
4.12.1 All instruments shall be cal
Page 97 and 98:
) Current generator (Instrument che
Page 99 and 100:
7.0 MATERIALS SUPPLY 7.1 Materials
Page 101 and 102:
STANDARD SPECIFICATION FOR INSTRUME
Page 103 and 104:
1 0 GENERAL 1.1 Scope 1.1.1 This st
Page 105 and 106:
per ASTM B 68M copper No. C 12200.
Page 107 and 108:
MAXIMUM WORKING PRESSURE AND HYDROS
Page 109 and 110:
NO. TITLE 1.0 GENERAL 2.0 DESIGN PH
Page 111 and 112:
d) List of deviations, if any, from
Page 113 and 114:
IS-3624 Specification for pressure
Page 115 and 116:
These drawings represent the nozzle
Page 117 and 118:
2 DESIGN PHILOSOPHY 2.1 Instrumenta
Page 119 and 120:
approval from purchaser. c) In case
Page 121 and 122:
2.14.1.6 Automatic sequential start
Page 123 and 124:
2.21.1 Instrument junction boxes sh
Page 125 and 126:
side. 2.24 Philosophy of Junction B
Page 127 and 128:
) All relays and solenoid valves sh
Page 129 and 130:
d) All receiver instruments shall b
Page 131 and 132:
lamp test push button shall be used
Page 133 and 134:
4.4.6 All hinges, screws and other
Page 135 and 136:
The type of thermocouple shall be s
Page 137 and 138:
operating value. c) Pressure switch
Page 139 and 140:
level gauges shall have side mounte
Page 141 and 142:
The integral flow assembly shall be
Page 143 and 144:
of valve like butterfly, ball, rota
Page 145 and 146:
drawings alongwith the timing calcu
Page 147 and 148:
4.13.9 All accessories like positio
Page 149 and 150:
4.16.1 Vibration and axial displace
Page 151 and 152:
of 140 to 150 kg/cm2g while chargin
Page 153 and 154:
eceiver at the camera side. The con
Page 155 and 156:
7.3 If at any point of time during
Page 157 and 158:
- rotary equipment running data etc
Page 159 and 160:
individual alarm in DCS. 7.12.5 All
Page 161 and 162:
7.14.25 Wiring colour code within t
Page 163 and 164:
shall be routed to process or flare
Page 165 and 166:
IP 55 and flame proof Ex˜d˜ suita
Page 167 and 168:
Each components and the system shal
Page 169 and 170:
f) All multi pair cables shall have
Page 171 and 172:
) Monel or any other tubing shall b
Page 173 and 174:
complete the job in all respect. 13
Page 175 and 176:
provided. v) For impulse line with
Page 177 and 178:
cables for insulation testing, ensu
Page 179 and 180:
calibrate the instruments which sha
Page 181 and 182:
LTD STANDARD SPECIFICATION FOR GAS
Page 183 and 184:
LTD 1.1.1 This specification, toget
Page 185 and 186:
LTD 2.2 Gas detection system shall
Page 187 and 188:
LTD 2.10.8 Software features a) Dat
Page 189 and 190:
LTD paint, colour as specified in J
Page 191 and 192:
LTD 2.13.3.1 Alarm annunciator shal
Page 193 and 194:
STANDARD SPECIFICATION FOR PRESSURE
Page 195 and 196:
1.0 GENERAL 1.1 Scope 1.1.1 This sp
Page 197 and 198:
a) Specification sheet for each gau
Page 199 and 200:
d) Flange face shall be as per clau
Page 201 and 202:
6.0 REJECTION 6.1 Vendor shall prep
Page 203 and 204:
STANDARD SPECIFICATION FOR SELF ACT
Page 205 and 206:
1.0 GENERAL 1.1 Scope 1.1.1 This st
Page 207 and 208:
summing up all the deviations, from
Page 209 and 210:
egulators shall have flanged end co
Page 211 and 212:
2.6 Finish 2.6.1 The body shall be
Page 213 and 214:
Page 215 and 216:
LTD S NO. TITLE 1 GENERAL CONTENTS
Page 217 and 218:
LTD 1.1.3 In the event of any confl
Page 219 and 220:
LTD d) Ring type joint flanges shal
Page 221 and 222:
LTD 2.6.6 In general, an actuator o
Page 223 and 224:
LTD Linearity and Hysterisis shall
Page 225 and 226:
GAIL (INDIA) LTD NEW DELHI Abbrevia
Page 227 and 228:
1.0 GENERAL 1.1 Scope 1.1.1 This sp
Page 229 and 230:
) Minimum number of eight PVC / rub
Page 231 and 232:
Smoke density rating not to exceed
Page 233 and 234:
iii) Shrinkage test iv) Hot deforma
Page 235 and 236:
GAIL (INDIA) LTD NEW DELHI STANDARD
Page 237 and 238:
CONTENTS 1.0 GENERAL 2.0 DESIGN AND
Page 239 and 240:
1.1.3 In the event of any conflict
Page 241 and 242:
the terminal block for terminating
Page 243 and 244:
3.2.1 The following information sha
Page 245 and 246:
Page 247 and 248:
CONTENTS 1.0 GENERAL 2.0 DESIGNS AN
Page 249 and 250:
specifically indicated, the specifi
Page 251 and 252:
sheet, the number of terminals for
Page 253 and 254:
4.3.2 In the event when witness ins
Page 255 and 256:
1 GENERAL CONTENTS 2 DESIGN AND CON
Page 257 and 258:
attached along with the material re
Page 259 and 260:
4.2 review: fittings. Vendor shall
Page 261 and 262:
GAIL (INDIA) LTD NEW DELHI HYDROSTA
Page 263 and 264:
1.0 GENERAL 2.0 DESIGN AND CONSTRUC
Page 265 and 266:
IS-2148 Electrical Apparatus for Ex
Page 267 and 268:
1.3 Drawing and Data 1.3.1 Detailed
Page 269 and 270:
1 Instruments Bottom Row Middle Row
Page 271 and 272:
a) 50 mm minimum space shall be pro
Page 273 and 274:
4.1 Unless otherwise specified, pur
Page 275 and 276:
Page 277 and 278:
1.0 GENERAL 2.0 DESIGN AND CONSTRUC
Page 279 and 280:
detailed technical offer is require
Page 281 and 282:
double block and bleed for the bypa
Page 283 and 284:
Annexure-1 of this specification. D
Page 285 and 286:
Page 287 and 288:
1.1 Scope 1.1.1 This specification,
Page 289 and 290:
proto-type design or items not meet
Page 291 and 292:
2.3.1 Body 2.3.1.1 Unless otherwise
Page 293 and 294:
connections shall be blinded / plug
Page 295 and 296:
) Hydrostatic test as per clause 4.
Page 297 and 298:
GAIL (INDIA) LTD NEW DELHI Abbrevia
Page 299 and 300:
1.0 General 1.1 Scope 1.1.2 This sp
Page 301 and 302:
manufactured outside India. e) Devi
Page 303 and 304:
Weatherproof housing IP-65 to IEC-6
Page 305 and 306:
alarm is provided as diagnostic mai
Page 307 and 308:
extra functionality and/or software
Page 309 and 310:
) Reading coefficient, if any c) Pe
Page 311 and 312:
Page 313 and 314:
Annexure 2 GASKETS MATERIAL REQUIRE
Page 315 and 316:
1.0 GENERAL GAIL (INDIA) LTD NEW DE
Page 317 and 318:
esponsibility shall include the fol
Page 319 and 320:
2.1.1 Temperature gauges shall be o
Page 321 and 322:
) Flanged end connections shall be
Page 323 and 324:
f) Review of all certificates and t
Page 325 and 326:
LTD SECTION 1.0 GENERAL TABLE of CO
Page 327 and 328:
LTD without any commercial implicat
Page 329 and 330:
LTD IEC 60079 Electrical Apparatus
Page 331 and 332:
LTD Direction of flow 4.9 Field act
Page 333 and 334:
LTD meters for the given process co
Page 335 and 336:
LTD Uncorrected and corrected forwa
Page 337 and 338:
LTD 9.1.1 PURCHASER may visit the p
Page 339 and 340:
LTD 9.4.1 Site Acceptance shall con
Page 341 and 342:
STANDARD SPECIFICATION FOR GAS CHRO
Page 343 and 344:
1.0 SCOPE 9.1 This specification co
Page 345 and 346:
H2S < ppm by weight S < ppm by weig
Page 347 and 348:
5.2 After placement of purchase ord
Page 349 and 350:
Gas Gr. IIA & IIB Temp T3. All anal
Page 351 and 352:
classification indicated in the pur
Page 353 and 354:
6.4.13 The programmer will be certi
Page 355 and 356:
c) Temperature, pressure and flow r
Page 357 and 358:
10.2 The approved spare parts and c
Page 359 and 360:
CONTENTS 1.0 SCOPE 2.0 DEFINITIONS
Page 361 and 362:
AGA Report No 3 Orifice Metering of
Page 363 and 364:
5.2.2 Analog inputs shall be 4-20 m
Page 365 and 366:
5.8.4 The minimum protocol supporte
Page 367 and 368:
such a way that the flow controller
Page 369 and 370:
6.3 GAS TURBINE METER CALCULATIONS
Page 371 and 372:
7.0 DATA MANAGEMENT AND USER INTERF
Page 373 and 374:
♦ Daily total of the standard vol
Page 375 and 376:
♦ Hourly averages of differential
Page 377 and 378:
♦ Calibrated Static Pressure Rang
Page 379 and 380:
Analog input Analog output 8.3.3 A
Page 381 and 382:
9.3.1 PURCHASER shall not be invite
Page 383 and 384:
VENDOR shall provide a schedule det
Page 385 and 386:
minimum the following topics shall
Page 387 and 388:
GAIL (INDIA) LTD NEW DELHI THERMOCO
Page 389 and 390:
GAIL (INDIA) LTD NEW DELHI THERMOWE
Page 391 and 392:
GAIL (INDIA) LTD NEW DELHI THERMOWE
Page 393 and 394:
GAIL (INDIA) LTD NEW DELHI INSTRUME
Page 395 and 396:
Page 397 and 398:
GAIL (INDIA) LTD NEW DELHI SUPPORT
Page 399 and 400:
GAIL (INDIA) LTD NEW DELHI CANOPY F
Page 401 and 402:
GAIL (INDIA) LTD NEW DELHI TRAY SUP
Page 403 and 404:
Page 405 and 406:
Page 407 and 408:
TUBING HOOK-UP WITH CONTROL VALVE A
Page 409 and 410:
GAIL (INDIA) LTD NEW DELHI PRESSURE
Page 411 and 412:
Page 413 and 414:
GAIL (INDIA) LTD NEW DELHI DP INSTR
Page 415 and 416:
Page 417 and 418:
Page 419 and 420:
Page 421 and 422:
GAIL (INDIA) LTD NEW DELHI DIMESION
Page 423 and 424:
1.0 SCOPE 2.0 REFERENCE DOCUMENTS 3
Page 425 and 426:
In case of conflict between the req
Page 427 and 428:
GAIL (INDIA) LTD NEW DELHI movement
Page 429 and 430:
4.25 All mounting accessories neede
Page 431 and 432:
8.1 All threaded and flanged openin
Page 433 and 434:
1. Stop Valve (3/4” NPT), 2. Chec
Page 435 and 436:
SL. NO GAIL (INDIA) LTD NEW DELHI G
Page 437 and 438:
1.0 SCOPE GAIL (INDIA) LTD NEW DELH
Page 439 and 440:
ASTM A-370 - Standard Test Methods
Page 441 and 442:
4.2 Valve body design shall be eith
Page 443 and 444:
) Flanged end, if specified, shall
Page 445 and 446:
d) Direction of operation of hand w
Page 447 and 448:
5.1.7 a) All finished wrought weld
Page 449 and 450:
) Test certificates of hydrostatic
Page 451 and 452:
k) List of recommended spares requi
Page 453 and 454:
STANDARD SPECIFICATION FOR PIPELINE
Page 455 and 456:
1.0 SCOPE This Specification covers
Page 457 and 458:
3.5 For all such valves where Carbo
Page 459 and 460:
4.12 Valves shall be suitable for e
Page 461 and 462:
) Body castings of valves shall be
Page 463 and 464:
d) Test report on operation of valv
Page 465 and 466:
c) Fabrication details of all valve
Page 467 and 468:
Page 469 and 470:
1.0 SCOPE This specification covers
Page 471 and 472:
4.9 All welds shall be made by weld
Page 473 and 474:
other suitable material. All valves
Page 475 and 476:
STANDARD SPECIFICATION FOR SEAMLESS
Page 477 and 478:
1.0 SCOPE This specification covers
Page 479 and 480:
e used for other hydrocarbon servic
Page 481 and 482:
9.0 DOCUMENTATION 9.1 Prior to ship
Page 483 and 484:
1.0 SCOPE 2.0 REFERENCE DOCUMENTS 3
Page 485 and 486:
MSS-SP-97 - Forged Carbon Steel Bra
Page 487 and 488:
maintained. Repair welding procedur
Page 489 and 490:
SPECIFICATION FOR QUICK OPENING END
Page 491 and 492:
SCOPE This specification covers the
Page 493 and 494:
4.6 End closure shall be provided w
Page 495 and 496:
7.3 Before shipment, closures shall
Page 497 and 498:
WELDING SPECIFICATION FOR FABRICATI
Page 499 and 500:
(This specification shall be used i
Page 501 and 502:
4.8 Tungsten electrodes used shall
Page 503 and 504:
8.2 Cleaning (a) The ends to be wel
Page 505 and 506:
GAIL (INDIA) LTD NEW DELHI Metal st
Page 507 and 508:
(h) Manufacturer's test certificate
Page 509 and 510:
Inspection of all welds shall be ca
Page 511 and 512:
(a) Whenever such tests are specifi
Page 513 and 514:
ELECTRODE QUALIFICATION TEST RECORD
Page 515 and 516:
Macro Test Results : Fracture Test
Page 517 and 518:
Soaking Time (Hrs.) _______________
Page 519 and 520:
FILLER METALS GAIL (INDIA) LTD NEW
Page 521 and 522:
GAIL (INDIA) LTD NEW DELHI EXHIBIT
Page 523 and 524:
OTHER TESTS Type of Test __________
Page 525 and 526:
Guided Bend Test Results Type of Fi
Page 527 and 528:
1. Name: 2. Identification: 3. Date
Page 529 and 530:
TECHNICAL NOTES FOR PIPES GAIL (IND
Page 531 and 532:
GAIL (INDIA) LTD NEW DELHI Material
Page 533 and 534:
Temp ( o F) Material A335 Gr. P 11
Page 535 and 536:
3.0 HYDROSTATIC TEST 3.1 All pipes
Page 537 and 538:
c) Stainless Steel E.FS.W (8” and
Page 539 and 540:
S. NO. TITLE 1.0 GENERAL 2.0 DOCUME
Page 541 and 542:
2.2.2 Test report shall be supplied
Page 543 and 544:
GAIL (INDIA) LTD NEW DELHI ANSI 600
Page 545 and 546:
3.18.5 The face-to-face dimensions
Page 547 and 548:
4.3 Where gear operator is not call
Page 549 and 550:
casting to be radiographed for type
Page 551 and 552:
GAIL (INDIA) LTD NEW DELHI BYPASS P
Page 553 and 554:
GAIL (INDIA) LTD NEW DELHI rating a
Page 555 and 556:
GAIL (INDIA) LTD NEW DELHI TECHNICA
Page 557 and 558:
1.7.4 All welded fittings shall be
Page 559 and 560:
1.20 Swage nipples (concentric/ecce
Page 561 and 562:
3.9 Each size of fitting shall be s
Page 563 and 564:
1.0 GENERAL 1.1 All items, their di
Page 565 and 566:
1.16 AWWA C207 flanges shall be hub
Page 567 and 568:
Page 569 and 570:
Page 571 and 572:
Page 573 and 574:
a. Sizes 26” and above b. Class 9
Page 575 and 576:
Abbreviations: PMI : Positive Mater
Page 577 and 578: 1.0 SCOPE This specification covers
Page 579 and 580: 2.13 Providing insert plates from c
Page 581 and 582: have been fabricated I erected. Mat
Page 583 and 584: Reinforcement pads shall be provide
Page 585 and 586: specification or isometric or line
Page 587 and 588: c. Hydrostatic Testing of the syste
Page 589 and 590: No pipe shoe I cradle shall be offs
Page 591 and 592: Abbreviation :- DP/LP: Dye Liquid P
Page 593 and 594: 1. GENERAL 1.1 SCOPE The specificat
Page 595 and 596: 12 Bead Deflection 2.5 mm or less 1
Page 597 and 598: 4. TABLE-I (with applicable Notes)
Page 599 and 600: IN SP N. CL AS S III TABLE 1 : CLAS
Page 601 and 602: 4. Magnetic particle & the Liquid p
Page 603 and 604: 7. Hardness Test: GAIL (INDIA) LTD
Page 605 and 606: c) Piping less than 38 mm (1.5”)
Page 607 and 608: Sl. No. Description 1. SCOPE 2. INS
Page 609 and 610: 1.0 SCOPE This specification covers
Page 611 and 612: Pumps, compressors and other rotary
Page 613 and 614: supports shall be removed only afte
Page 615 and 616: When testing with air, pressure sha
Page 617 and 618: GAIL (INDIA) LTD NEW DELHI CONTENTS
Page 619 and 620: 1.0 GENERAL 1.1 These technical spe
Page 621 and 622: IS-5 : Colour coding IS-101 : Metho
Page 623 and 624: period, at his sole discretion and
Page 625 and 626: The compatibility of finishing coat
Page 627: k. If spray gun shows choking, imme
Page 631 and 632: GAIL (INDIA) LTD NEW DELHI DOCUMENT
Page 633 and 634: 6.0 PAINT MATERIALS Paint manufactu
Page 637 and 638: F-14: Specially formulated polyamin
Page 651 and 652: 18.2 The colour code scheme is inte
Page 653 and 654: 19.0 IDENTIFICATION OF VESSELS, PIP
Page 655 and 656: pinhole detector and positector whe
Page 657 and 658: DENSITY - D 1475 DIPPING PROPERIES
Page 665 and 666: STANDARD SPECIFICATION FOR POSITIVE
Page 667 and 668: 1.0 SCOPE This specification applie
Page 669 and 670: 5.2 Instrument or methods used for
Page 671 and 672: GAIL (INDIA) LTD NEW DELHI POSITIVE
Page 673 and 674: GAIL (INDIA) LTD NEW DELHI CONTENTS
Page 675 and 676: 3.0 SCOPE OF SERVICES 4.0 DESIGN (i
Page 677 and 678: 5.10 All nozzles above 3" NB size s
Page 679 and 680:
(a) Ultrasonic Examinations GAIL (I
Page 681 and 682:
(iv) All Environment (temp. 80-400
Page 683 and 684:
11.11 Manufacturer related informat
Page 685 and 686:
GAIL (India) Limited New Delhi CONT
Page 687 and 688:
4.0 CLASS DESIGNATION CODE The pipi
Page 689 and 690:
10.4 For RTJ flanges, octagonal rin
Page 691 and 692:
Sl. No. 1 2 Pipeline Specialty item
Page 693 and 694:
GAIL (India) Limited New Delhi ANNE
Page 695 and 696:
BRANCH PIPE (SIZE IN INCHES) GAIL (
Page 697 and 698:
FLNG.FIG8 02.000 08.000 B-16.48 AST
Page 699 and 700:
Page 701 and 702:
BRANCH PIPE (SIZE IN INCHES) GAIL (
Page 703 and 704:
T.EQUAL 02.00 06.00 STD B 16.11 AST
Page 705 and 706:
Page 707 and 708:
BRANCH PIPE (SIZE IN INCHES) (B1A)
Page 709 and 710:
FLNG.FIG8 02.000 08.000 B-16.48 AST
Page 711 and 712:
GAIL (India) Limited New Delhi PIPI
Page 713 and 714:
PIPING CLASS : D1A, 600 # BASE MATE
Page 715 and 716:
BRANCH PIPE (SIZE IN INCHES) 72 72
Page 717 and 718:
FLNG.BLIND 00.500 01.500 B-16.5 AST
Page 719 and 720:
VLV.BALL 02.000 24.000 API-6D BODY-
Page 721 and 722:
PIPING CLASS : A4A, 150 # BASE MATE
Page 723 and 724:
CODE DESCRIPTION F SADDLE FUSED JT
Page 725 and 726:
Gasket Group (A4A) GASKET 00.500 14
Page 727 and 728:
PIPING CLASS : B4A, 300 # BASE MATE
Page 729 and 730:
Page 731 and 732:
VLV.GLOBE 02.000 12.000 BS- 1873 VL
Page 733 and 734:
PIPING CLASS : D4A, 600 # BASE MATE
Page 735 and 736:
Page 737 and 738:
CPLNG.RED 01.000 01.500 B-16.11 AST
Page 739 and 740:
PIPING CLASS : J2A, 150 # BASE MATE
Page 741 and 742:
Page 745 and 746:
CAPACITY AUGMENTATION OF AJPL (Ph-1
Page 747 and 748:
Contractor Client GAIL INDIA LTD ,N
Page 749 and 750:
Contractor Client GAIL INDIA LTD ,N
Page 751 and 752:
Sl. No Item Contractor Client GAIL
Page 753 and 754:
CONTRACTOR’S SCOPE OF SUPPLY AND
Page 755 and 756:
NOTE: 1. INSTALLATION SUPERVISION &
Page 757 and 758:
1.0 BIDDER DRAWING/DOCUMENT REQUIRE
Page 759 and 760:
(including foundation details, 16 w
Page 761 and 762:
Page 763 and 764:
Sl. No. Description Bidder’s Resp
Page 765 and 766:
Sl. No. Description Bidder’s Resp
Page 767 and 768:
VENDOR LIST The materials required
Page 769 and 770:
1) Forain S.R.L. 2) GD Engineering
Page 771 and 772:
18) M/s Sakhi Engineers Pvt. Ltd. 1
Page 773 and 774:
7) M/s CMI Limited 8) M/s - Cords C
Page 775 and 776:
4) Goodluck Steel Tubes Ltd, India
Page 777 and 778:
5) Chemtrols Engineering Ltd, India
Page 779 and 780:
8) Nagman Sensors Pvt Ltd 9) Tecnom
Page 781 and 782:
incomplete and incorrect Checklist
Page 783 and 784:
PERFORMANCE GUARANTEE CERTIFICATE (
Page 785 and 786:
EQUIPMENT QUALIFICATION CRITERION (
Page 787 and 788:
Company symbol(insert FACTORY ACCEP
Page 789 and 790:
1. PREFACE 1.1 Introduction: This d
Page 791 and 792:
2. VISUAL INSPECTION OF SKID. 2.1 S
Page 793 and 794:
1. Check the functional test as per
Page 795 and 796:
Any discrepancy observed during FAT
Page 797 and 798:
Company symbol(insert TEST CERTIFIC
Page 799 and 800:
Page 801 and 802:
Company symbol(insert FAT CHECK LIS
Page 803 and 804:
Page 805 and 806:
Page 807 and 808:
Page 809 and 810:
Page 811 and 812:
Page 813 and 814:
_____________________ _____________
Page 815 and 816:
Standard Register List in Flow comp
Page 817 and 818:
GAIL (INDIA) LTD NEW DELHI DATA SHE
Page 819 and 820:
1. This Valve Data Sheet shall be r
Page 821 and 822:
GAIL (INDIA) LTD NEW DELHI CONTROL
Page 823 and 824:
DATA SHEETS DIFFERENTIAL PRESSURE I
Page 825 and 826:
Page 827 and 828:
“ * “ By Vendor, “**”-From
Page 829 and 830:
UNITS : Gas Flow - MMSCMD, Liquid F
Page 831 and 832:
Page 833 and 834:
Notes ** Refer Process data mention
Page 835 and 836:
PRESSURE GAUGES (TYPICAL) UNITS: Fl
Page 837 and 838:
Page 839 and 840:
GAIL (INDIA) LTD NEW DELHI Receiver
Page 841 and 842:
Receiver INDICATOR Instruments (Typ
Page 843 and 844:
Page 845 and 846:
Page 847 and 848:
Page 849 and 850:
DATA SHEETS TEMPERATURE TRANSMITTER
Page 851 and 852:
Page 853 and 854:
NOTES: * TO BE FURNISHED BY VENDOR
Page 855 and 856:
GAIL (INDIA) LTD NEW DELHI INTRINSI
Page 857 and 858:
DATA SHEETS LEL DETECTOTS/ TRANSMIT
Page 859 and 860:
Page 861 and 862:
Page 863 and 864:
GAIL (INDIA) LTD NEW DELHI BALL VAL
Page 865 and 866:
GAIL (INDIA) LTD NEW DELHI GLOBE VA
Page 867 and 868:
Page 869:
GAIL (INDIA) LTD NEW DELHI PLUG VAL
show all

standard specification for erection tender - GAIL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?