9363692, Operating manual HDTV Satellite receiver UFS ... - Kathrein

More documents

Recommendations

Info

16 Connection and Setup Connect the satellite receiver (HDMI or alternatively a video socket) and the TV set using a HDMI or video cable (see “Connection Example”). If your TV has a stereo feature, you can receive the sound in stereo via the HDMI connection. If you want to play the sound on your hi-fi system, connect the audio cinch sockets to the input sockets on the hi-fi system, using an appropriate cable (see “Connection example”). The fi bre-optic cable output is intended for the connection of a Dolby Digital system (see “Connection example”). Remove the cover on the rear of the remote control. Insert the two batteries supplied into the remote control. Ensure correct polarity of the batteries; the + and – markings as indicated inside the battery compartment. Slide the cover back onto the housing until it locks in place.
Connection and Setup The four screw sockets provided (see diagram below) allow you to install the receiver not only resting on a shelf but also to fi x it there or in other positions. When selecting the installation location, take care that it conforms to the instructions in the section “Safety Instructions”! When selecting the installation location, consider the following points: Ventilation: The heat generated within the receiver can be dissipated from the following sides of the casing: Bottom, left, right and top. When selecting the installation location, make sure that these sides are not obstructed or covered. If the unit is operated continuously with insuffi cient ventilation, this can negatively affect the length of its working life! The unit monitors its temperature in operation. Premature failure of the unit due to continuous operation at temperatures higher than the recommended operating temperature as a result of insuffi cient ventilation does not constitute grounds for a claim under warranty/guarantee. Connections and fusing of the unit: All connection cables for connection to the receiver (including the infra-red sensor) are connected at the rear of the unit (see also the item “Connection example” in this section). When selecting the installation location, allow suffi cient clearance at the rear of the unit for these cables and their plugs. On the left hand side of the receiver viewed from the front there is a fuse inserted from the outside. This fuse (for the type, see the section “Important Information”) should be accessible even after the unit has been installed, so that it can easily be exchanged if required. Removing the blanking plugs: When the unit is delivered, the screw sockets are covered with blanking plugs. These can be pushed out, using the screws supplied (working upwards from below, see diagram on the right). 20 cm Minimum clearance Maintain a clearance of at least 20 cm above or below the unit, 2 cm to either side and 5 cm behind it, to allow unobstructed dissipation of the heat generated. 2 cm 5 cm 5 cm 2 cm 17
Page 1 and 2: Operating manual Englisch UFS 940sw
Page 3 and 4: List of Contents Preface...........
Page 5 and 6: List of Contents Antenna Configurat
Page 7 and 8: Safety Instructions - Important Inf
Page 9 and 10: The power supply unit and the recei
Page 11 and 12: Reception of digital satellite TV a
Page 13 and 14: 1. Cable guide for infra-red sensor
Page 15: Dolby Digital system Connection and
Page 19 and 20: Use of other screws: If because of
Page 21 and 22: Connection and Setup Required butto
Page 23 and 24: Show 4:3 event Here you can select
Page 25 and 26: Number of Satellites When selecting
Page 27 and 28: Satellite selection When selecting
Page 29 and 30: Set borders Connection and Setup Yo
Page 31 and 32: Connection and Setup Use the butto
Page 33 and 34: Confi gure satellites Press the bu
Page 35 and 36: Satellite and Position When selecti
Page 37 and 38: LNB Type (settings) Use the button
Page 39 and 40: Transmission channel Use the butto
Page 47 and 48: If you do not wish to perform a cha
Page 49 and 50: Local time offset (UTC) Connection
Page 51 and 52: General Operating Instructions Conf
Page 53 and 54: Basic Operation in TV or Radio Mode
Page 65 and 66: EPG (Electronic Programme Guide) -
Page 67 and 68:
EPG (Electronic Programme Guide) Th
Page 69 and 70:
The search function can be called u
Page 71 and 72:
Programme not in EPG: Select any pr
Page 73 and 74:
EPG (Electronic Programme Guide) Re
Page 75 and 76:
If you want to be reminded that a p
Page 77 and 78:
Editing options for the reminder fu
Page 79 and 80:
Select a channel in the selected ch
Page 81 and 82:
Use the buttons to select “Lock
Page 83 and 84:
See “Edit channels (channel lists
Page 85 and 86:
Recording Archive (Play Back/Edit R
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Edit Channel List (see section Edit
Page 95 and 96:
During the search you will see the
Page 97 and 98:
Transponder Frequency Mainmenu - Se
Page 99 and 100:
After calling up the menu you will
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Mainmenu - Settings Always follow t
Page 109 and 110:
Mainmenu - Settings Information for
Page 111 and 112:
Page 113 and 114:
Mainmenu - Service Menu A pre-requi
Page 115 and 116:
Page 117 and 118:
Use the buttons to select “Manag
Page 119 and 120:
In the event of a malfunction, fi r
Page 121 and 122:
Connections Technical Appendix Sat
Page 123 and 124:
Sat IF Sat IF Sat IF Technical Appe
Page 125 and 126:
Sat IF Technical Appendix Sat IF **
Page 127 and 128:
HD - Ready This is a label created
Page 129 and 130:
Service If, despite studying this o
Page 131 and 132:
For your Notes 131
show all

9363692, Operating manual HDTV Satellite receiver UFS ... - Kathrein

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?