RK06/RK07 Disk Drive User's Manual - Trailing-Edge

More documents

Recommendations

Info

. For a serial number ABC, enter the BCD equivalent of digit A in Row 1, Column A; enter the BCD equivalent of digit B in Row 1, Column B; enter the BCD equivalent of digit C in Row 1, Column C. c. Enter the complement of Row 1 in Row 2. d. For every "1" in Row 1, wire the appropriate backplane pin (below Row 1 and Row 2) to pin D6H 1 (+3 V). For every "1" in Row 2, wire the appropriate pin to A6Tl (ground). e. If the drive is an RK06, wire 01 VI to AITI (ground). If the drive is an RK07, wire 01Vl to D6Hl (+3 V). 7. If the installation is multidrive, proceed to step 8; otherwise, proceed to step 10. 8. Connect drive bus cable (PN-70-12292-xx) from J2 (A OUT) of the previous drive to Jl (A IN) of the next drive. Repeat for each additional drive. The standard length between drives is 2.44 m (8 ft); however, optional length cables are available. Total drive bus length must not exceed 30.48 m (l00 ft). 9. Daisy chain each drive, using a ground wire (PN-7212827-8) between the ground studs in the drive cabinets. RK06-XA OR RK07-XA RK06-XB OR RK07-XB RK06-XC OR RK07-XC RK06-XD OR RK07-XD 115 VAC/60 HZ 230 VAC/60 HZ 115 VAC/50 HZ 230 VAC/50 HZ [Q! DODDI UNIT-SELECT PLUG 11-4980 Figure 4-6 Serial Tag Location and Model Identifications (Tag Visible with Front Cover Removed) 4-11
DC POWER CABLE CNPl CNP2 CNP3 CNP4 CNP5 Figure 4-7 RK06/RK07 I/O Connector Details 4-12 CNP6 7897-14 CABLE BOARD (M7706) J2 A OUT AND TERMINATOR J4 BOUT Jl A IN AND J3 BIN
Page 1 and 2:
RK06/RK07 Disk Drive User's Manual
Page 4 and 5: 3.1.5 3.1.6 3.1.7 3.1.8 3.1.9 3.2 3
Page 6: CHAPTER 7 7.1 7.2 7.2.1 7.2.2 7.2.3
Page 13: • Mean-time-to-repair (MTTR) for
Page 17 and 18: Characteristics RK06K-DC Cartridge
Page 19 and 20: Characteristics Seek times Average
Page 21: Option RK07-EA RK07-EB RK07-EC RK07
Page 27 and 28: Address ( octal) Type 777440 R/W 77
Page 33: Multiple Drive Select Line When ass
Page 39 and 40: 3.1.7 Radiated Emissions The effect
Page 41: 25-CFM AIR HOSE CARTIDGE POWER SUPP
Page 46: FULL TELESCOPE CAP (9906446) 6-PANE
Page 53: 4.3.2 RK06 or RK07 Disk Drive To in
Page 59: 4.4.1 Controller Power Supply Volta
Page 62 and 63: HEAD 1 HEADO Figure 4-11 RK07 Head
Page 67 and 68: Switch SYNC CLOCK HALTON ERROR ADDR
Page 69 and 70: 4.6 DUAL ACCESS DRIVE INSTALLATION
Page 71 and 72: CHAPTER 5 FIELD ACCEPTANCE TEST PRO
Page 74 and 75: Program Table 5-2 Diagnostic Progra
Page 76 and 77: Program Table 5-2 Diagnostic Progra
Page 78 and 79: 5. Load DZR6E; run two passes with
Page 83 and 84: 6.2.3 UNIT SELECT Switch with READY
Page 85 and 86: 7. Depress one or both of the ACCES
Page 87 and 88: TOP COVER HANDLE HANDLE SLIDE Figur
Page 89 and 90: Figure 6-6 Positioning for Load 6-9
Page 91 and 92: Figure 6-8 Installing Protection Co
Page 97 and 98: Combined Error/Controller Clear (CE
Page 104:
h. Read/Write unsafe (Message BO:TI
Page 108:
Offset (OFO-OF7) - Bits 0-7 - The O
Page 112:
7.2.14 Maintenance Register 2 (RKMR
Page 124 and 125:
Control Clock - One control clock c
Page 126:
7. Check for the setting of the Rea
Page 131 and 132:
RKCS1= RKCS2= RKDS= RKER= RKDC= RKO
Page 134:
2. Error correction is accomplished
Page 138 and 139:
RIM CONE Figure 8-1 Spindle Assembl
Page 144:
9.4.3 Caution in Issuing a Release
Page 150 and 151:
- - - - - - - - - - - FoldHere - -
show all

RK06/RK07 Disk Drive User's Manual - Trailing-Edge

Create successful ePaper yourself

Delete template?

Save as template?