FTA Manual.pdf - Industrial Air

More documents

Recommendations

Info

Installation / System 63 9810.0156 – Rev.04 –12/01/2007 It is suggested that after installation filling and air ventilation processes are completed, installation pumps must circulate the water in the system about one hour. It is neccesary to release last air molecules and activate the system completely. During the test circulation, pump and/or pumps must be in use. Caution: Boiler must not be operated certainly without providing the water pressure completely and releasing the air in the installation. Boiler must be observed for a while after it is activated, boiler water level must be controlled and observed constantly by the suitable manometer which is mounted to a convenable and traceable place in the installation. In case of a different pump mounting onto boiler to provide hot water, circulation lines must be checked carefully. In case of 4 way valve usage, water heating installation should be done through another exchanger to prevent wrong circulation. Discharging of the Condense Water Caution! Condense water occured during heating process must be transferred via an convenable neutralizer installation(accessory). pH value is between 3 and 4 for gas fuels and between 2 and 3 for liquid fuels. Therefore suitable neutralizer must be used. Condense water line must be installed as slanting. The line going to channel connection must be seen clearly. Bottom drainage line must be under the chimney hood level. Neutralizer installation is not required for the liquid fuel which has low rate sulfur (In accordance with ATV note page A251). Generally , there is no need to neutralizer installation in the boiler having 200 kW nominal heating power. For the neutralization of the boiler outlet water, local waste water specifications and\or local specifications must be taken into consideration. 36 www.baymak.com.tr
5.3 Chimney Connection 63 9810.0156 – Rev.04 –12/01/2007 Installation / System Caution! Waste gas way must be as short as possible. Waste gas pipes must be installed as in slanting direction towards chimney and connections must have full imperviousness. The chimney must be designed considering technical specifications determined in DIN 4705 and built according to DIN 18160. Both boiler back pressures and boiler pressures must be in consideration at chimney calculations. If the waste gas heat is under 160°C in continuous operating, it is forbidden to use an ordinary chimney. Warning! ! To change the burner power may effect waste gas temperature. It is advised to attach an absorbtion restrictive for high rating exhaust chimneys. 37
Page 1 and 2: YAKUT-ELMAS / YAKUT PLUS ELMAS PLUS
Page 3 and 4: Table of Contents: CAUTION! 6. Oper
Page 5 and 6: 1.2 Symbols in the manual 1.3 Users
Page 7 and 8: 63 9810.0156 - Rev.04 -12/01/2007 S
Page 9 and 10: 3. Installation 3.1 Delivery Conten
Page 11 and 12: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 13 and 14: BOILER TYPE 3.2 Space Requirement f
Page 15 and 16: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 17 and 18: Installation 3.6 Gas Blown Burners
Page 19 and 20: 3.9 Before First Start -Up 63 9810.
Page 21 and 22: 3.10 Control of water pressure 3.11
Page 23 and 24: 4. Mounting 63 9810.0156 - Rev.04 -
Page 25 and 26: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 27 and 28: 4.2 Burner mounting . 63 9810.0156
Page 29 and 30: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 31 and 32: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 33 and 34: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 35: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 39 and 40: 5.4 Installation of Shunt Pump 63 9
Page 41 and 42: 6.2 Temperatures of Installation Wa
Page 43 and 44: 6.4 Training of Operator 63 9810.01
Page 45 and 46: Assemble of Turbulators : 63 9810.0
Page 47 and 48: Suggestions for Energy Saving 8. Su
Page 49 and 50: 9. Important Cautions 9.1 Important
Page 51 and 52: 10. Technical Data 10.1 Technical D
Page 53 and 54: 63 9810.0156 - Rev.04 -12/01/2007 T
Page 55 and 56: 63 9810.0156 - Rev.04 -12/01/2007 W

FTA Manual.pdf - Industrial Air

Create successful ePaper yourself

Delete template?

Save as template?