FTA Manual.pdf - Industrial Air

More documents

Recommendations

Info

Installation / System 5.2 Control And Filling of the System 63 9810.0156 – Rev.04 –12/01/2007 Ensure that deliver and flow connections on the boiler are correct. Check the leakproof of the system. Recommended water pressure must be as much as boiler operation pressure (maximum water pressure can not be much more than boiler test pressure). For the control of safety valve and its equipments after checking the system leakproofness, increase the system pressure 0,5 bar over boiler maximum operation pressure temporarily. Operation control of the safety valves must be done under this pressure. The equipment which is inactive and/or response lately must be changed with a new one and the tests must be repeated. Tests must be done absolutely under management of an expert installer. Otherwise boiler will be out of warranty and manufacturer will not be responsable for the damages. Check the connection line of boiler expansion tank, ensure that there is no any valve between boiler and expansion tank. Pump the water to the central heating unit. This process must be slowly as much as possible.So, the air in the installation can be released by the air releasing devices regularly. Caution: There must be a standardized CE mark water filter on the filling line. Otherwise particles or pieces in the water may be harmful for the system directly or indirectly.Under these circumstances, boiler will be out of warranty. Discharging line and drainage of the safety valve must be connected to a convenient drainage line and must be noticable and viewable. 34 www.baymak.com.tr
63 9810.0156 – Rev.04 –12/01/2007 Installation / System Filling process must be finished providing convenient water pressure to the installation. ( For the convenient water pressure value, please get information from authorized service and installer company’s authority ). Water pressure must not exceed upper than 3 bar (maximum operation pressure). Fillling process must be done by an expert and relief of the air in installation must be done correctly. After the installation is filled completely, air relief process must be done and the air on the pumps must be released by activating the pumps at temporary times. To release the air on the pump, opening the wet rotor sleeve as shown, both turning direction of pump is checked or air in the pump is relased Electricshock Danger! Before protective hat and pieces of cover is taken out, all electrical connections on boiler must be disassembled. Works that will be done when electric is on, must be carried on by authorized people after all necessary precuations are supplied. 35
Page 1 and 2: YAKUT-ELMAS / YAKUT PLUS ELMAS PLUS
Page 3 and 4: Table of Contents: CAUTION! 6. Oper
Page 5 and 6: 1.2 Symbols in the manual 1.3 Users
Page 7 and 8: 63 9810.0156 - Rev.04 -12/01/2007 S
Page 9 and 10: 3. Installation 3.1 Delivery Conten
Page 11 and 12: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 13 and 14: BOILER TYPE 3.2 Space Requirement f
Page 15 and 16: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 17 and 18: Installation 3.6 Gas Blown Burners
Page 19 and 20: 3.9 Before First Start -Up 63 9810.
Page 21 and 22: 3.10 Control of water pressure 3.11
Page 23 and 24: 4. Mounting 63 9810.0156 - Rev.04 -
Page 25 and 26: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 27 and 28: 4.2 Burner mounting . 63 9810.0156
Page 29 and 30: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 31 and 32: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 33: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 37 and 38: 5.3 Chimney Connection 63 9810.0156
Page 39 and 40: 5.4 Installation of Shunt Pump 63 9
Page 41 and 42: 6.2 Temperatures of Installation Wa
Page 43 and 44: 6.4 Training of Operator 63 9810.01
Page 45 and 46: Assemble of Turbulators : 63 9810.0
Page 47 and 48: Suggestions for Energy Saving 8. Su
Page 49 and 50: 9. Important Cautions 9.1 Important
Page 51 and 52: 10. Technical Data 10.1 Technical D
Page 53 and 54: 63 9810.0156 - Rev.04 -12/01/2007 T
Page 55 and 56: 63 9810.0156 - Rev.04 -12/01/2007 W

FTA Manual.pdf - Industrial Air

Create successful ePaper yourself

Delete template?

Save as template?