FTA Manual.pdf - Industrial Air

More documents

Recommendations

Info

Cleaning and Maintenance 7. Cleaning and Maintenance 7.1 Cleaning 63 9810.0156 – Rev.04 –12/01/2007 Electricshock Danger! Before protective hat and pieces of cover is taken out, all electrical connections on boiler must be disassembled. Works that will be done when electric is on, must be carried on by authorized people after all necessary precuations are supplied. Cleaning consists of items below; - Cleaning of the boiler from outside, - Cleaning of combustion chamber and pipes of the boiler ( this may change depending on operation). It is strongly advised that cleaning and maintenance of boiler must be done once in a year by authorized services. Attention: Insulation of front cover was made by a material that is not required to be cleaned. Therefore, do not clean with any shape or corrosive tool, do not apply force or pressurized air, do not clean with fluids like water, etc. In case of damage on cover insulation, boiler will be out of warranty. For cleaning of combustion chamber in boiler room, open boiler cover, pull and take out turbulators with tools which was delivered with the boiler. After turbulators are taken out, clean them with a brush and brush holder, clean smut and dirts accumulating to the side of flume hood taking out the explotion hoot then repeating all the works from reverse, assemble explosition hoot and turbulators, close boiler cover and after bolts are tighten check if there is gas leakage from connections. See figure of turbulator assemble for process of connection and disconnection of turbulators. Burner must be checked for impurity, cleaned and processed to maintenance if it is necessary. In case of necessity, clean boilers from outside. Use only soft cleaning materials which will not damage to surface. Cleaning of surfaces, heating the inside of the boiler and burner, must be only done by authorized service. 44 www.baymak.com.tr
Assemble of Turbulators : 63 9810.0156 – Rev.04 –12/01/2007 Cleaning and Maintenance All turbulators must be located into pipe (see figure below) after related applications are done using related tools. All turbulators must be pushed till last point they can go 45
Page 1 and 2: YAKUT-ELMAS / YAKUT PLUS ELMAS PLUS
Page 3 and 4: Table of Contents: CAUTION! 6. Oper
Page 5 and 6: 1.2 Symbols in the manual 1.3 Users
Page 7 and 8: 63 9810.0156 - Rev.04 -12/01/2007 S
Page 9 and 10: 3. Installation 3.1 Delivery Conten
Page 11 and 12: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 13 and 14: BOILER TYPE 3.2 Space Requirement f
Page 15 and 16: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 17 and 18: Installation 3.6 Gas Blown Burners
Page 19 and 20: 3.9 Before First Start -Up 63 9810.
Page 21 and 22: 3.10 Control of water pressure 3.11
Page 23 and 24: 4. Mounting 63 9810.0156 - Rev.04 -
Page 25 and 26: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 27 and 28: 4.2 Burner mounting . 63 9810.0156
Page 29 and 30: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 31 and 32: 63 9810.0156 - Rev.04 -12/01/2007 M
Page 33 and 34: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 35 and 36: 63 9810.0156 - Rev.04 -12/01/2007 I
Page 37 and 38: 5.3 Chimney Connection 63 9810.0156
Page 39 and 40: 5.4 Installation of Shunt Pump 63 9
Page 41 and 42: 6.2 Temperatures of Installation Wa
Page 43: 6.4 Training of Operator 63 9810.01
Page 47 and 48: Suggestions for Energy Saving 8. Su
Page 49 and 50: 9. Important Cautions 9.1 Important
Page 51 and 52: 10. Technical Data 10.1 Technical D
Page 53 and 54: 63 9810.0156 - Rev.04 -12/01/2007 T
Page 55 and 56: 63 9810.0156 - Rev.04 -12/01/2007 W

FTA Manual.pdf - Industrial Air

Create successful ePaper yourself

Delete template?

Save as template?