8.3.17.0 - Force10 Networks

More documents

Recommendations

Info

www.dell.com | support.dell.com Figure 14-5. LLDP-MED Policies TLV TLV Type (127) TLV Length (8) Organizationally Unique ID (00-12-BB) Extended Power via MDI TLV The Extended Power via MDI TLV enables advanced power over ethernet (PoE) management between LLDP-MED endpoints and network connectivity devices (Figure 14-6). Advertise the Extended Power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. • Power Type—there are two possible power types: power sourcing entity (PSE) or power device (PD). The Dell Force10 system is a PSE, which corresponds to a value of 0, based on the TIA-1057 specification. • Power Source—there are two possible power sources: Primary and Backup. The Dell Force10 system is a Primary Power Source, which corresponds to a value of 1, based on the TIA-1057 specification. • Power Priority—there are three possible priorities: Low, High, and Critical. On Dell Force10 systems, the default power priority is High, which corresponds to a value of 2 based on the TIA-1057 specification. You can configure a different power priority through the CLI. Dell Force10 also honors the power priority value sent by the powered device. However, the CLI configuration takes precedence. • Power Value—Dell Force10 advertises the maximum amount of power that can be supplied on the port. By default it is 15.4W, which corresponds to a Power Value of 130, based on the TIA-1057 specification. You can advertise a different Power Value using the max-milliwatts option with the power inline auto | static command. Dell Force10 also honors the power value (power requirement) sent by the powered device when the port is configured for power inline auto. Figure 14-6. Extended Power via MDI TLV 172 | Link Layer Discovery Protocol (LLDP) Organizationally Defined Sub-type (2) 7 bits 9 bits 3 octets 1 octet TLV Type (127) TLV Length (7) Organizationally Unique ID (00-12-BB) Organizationally Defined Sub-type (4) Application Type (0-255) 1 octet Power Type (0) U T 3 bits X (0) Power Source (1) VLAN ID (0-4095) 12 bits Power Priority (2) 7 bits 9 bits 3 octets 1 octet 2 bits 2 bits 4 bits L2 Priority (0-7) DSCP Value (0-63) 3 bits 6 bits Power Value (130) 2 octets fnC0056mp
LLDP Operation On an Aggregator, LLDP operates as follows: • LLDP is enabled by default. • LLDPDUs are transmitted and received by default. LLDPDUs are transmitted periodically. The default interval is 30 seconds. • LLDPDU information received from a neighbor expires after the default Time to Live (TTL) value: 120 seconds. • FTOS supports up to eight neighbors per interface. • FTOS supports a maximum of 8000 total neighbors per system. If the number of interfaces multiplied by eight exceeds the maximum, the system does not configure more than 8000. • LLDP is not hitless. Viewing the LLDP Configuration To display the LLDP configuration, use the show config command in either CONFIGURATION or INTERFACE mode (Figure 14-7) and (Figure 14-8). Figure 14-7. Viewing LLDP Global Configurations R1(conf)#protocol lldp R1(conf-lldp)#show config ! protocol lldp advertise dot1-tlv port-protocol-vlan-id port-vlan-id advertise dot3-tlv max-frame-size advertise management-tlv system-capabilities system-description hello 10 no disable R1(conf-lldp)# Figure 14-8. Viewing LLDP Interface Configurations R1(conf)#interface tengigabitethernet 1/31 R1(conf-if-te-1/31)#show config ! interface TenGigabitEthernet 1/31 no ip address ! no shutdown R1(conf-if-te-1/31)#protocol lldp R1(conf-if-te-1/31-lldp)#show config ! protocol lldp R1(conf-if-te-1/31-lldp)# Link Layer Discovery Protocol (LLDP) | 173
Page 1 and 2:
Dell PowerEdge Configuration Guide
Page 3 and 4:
October 2012 | iii
Page 5 and 6:
1 About this Guide . . . . . . . .
Page 7 and 8:
Data Center Bridging Exchange Proto
Page 9 and 10:
Displaying VLAN Membership . . . .
Page 11 and 12:
Read Managed Object Values . . . .
Page 13 and 14:
Troubleshooting Packet Loss . . . .
Page 15 and 16:
About this Guide Objectives 1 This
Page 17 and 18:
Before You Start Default Settings 2
Page 19 and 20:
DCB Support DCB enhancements for da
Page 21 and 22:
The untagged VLAN of a server-facin
Page 23 and 24:
Configuration Fundamentals 3 The De
Page 25 and 26:
Navigating CLI Modes The FTOS promp
Page 27 and 28:
Figure 3-5. Undoing a command with
Page 29 and 30:
Table 3-2. Short-Cut Keys and their
Page 31 and 32:
Multiple Users in Configuration Mod
Page 33 and 34:
Getting Started This chapter contai
Page 35 and 36:
Uplink Ports Ports 33 to 56 are ext
Page 37 and 38:
Step Task (continued) Note: Termina
Page 39 and 40:
Figure 4-4. Completed Boot Process
Page 41 and 42:
Figure 4-6. Completed Boot Process
Page 43 and 44:
Access the Aggregator Remotely Conf
Page 45 and 46:
Dell Force10 recommends using the e
Page 47 and 48:
Figure 4-10 shows an example of usi
Page 49 and 50:
To view the contents of a file, fol
Page 51 and 52:
Figure 4-14. Alternative Storage Lo
Page 53 and 54:
Aggregator Management This chapter
Page 55 and 56:
Changing System Logging Settings Yo
Page 57 and 58:
Configuring a UNIX Logging Facility
Page 59 and 60:
Enabling the FTP Server To enable t
Page 61 and 62:
Recovering from a Forgotten Passwor
Page 63 and 64:
Figure 5-5. Recovering from a Faile
Page 65 and 66:
Data Center Bridging (DCB) 6 On an
Page 67 and 68:
Figure 6-1. Priority-Based Flow Con
Page 69 and 70:
Data Center Bridging Exchange Proto
Page 71 and 72:
QoS dot1p Traffic Classification an
Page 73 and 74:
How Enhanced Transmission Selection
Page 75 and 76:
DCB Policies in a Switch Stack A DC
Page 77 and 78:
Note: On a DCBX port, application p
Page 79 and 80:
Auto-Detection of the DCBX Version
Page 81 and 82:
DCBX Error Messages An error in DCB
Page 83 and 84:
Figure 6-7. show interfaces pfc sum
Page 85 and 86:
Table 6-3. show interface pfc summa
Page 87 and 88:
Table 6-4. show interface ets detai
Page 89 and 90:
Figure 6-12. show interface dcbx de
Page 91 and 92:
Example: PFC and ETS Operation This
Page 93 and 94:
Table 6-8. Example: priority group-
Page 95 and 96:
Skippy812 Dynamic Host Configuratio
Page 97 and 98:
Assigning an IP Address Using DHCP
Page 99 and 100:
Releasing and Renewing DHCP-based I
Page 101 and 102:
Figure 7-5. DHCP Client: Debug Mess
Page 103 and 104:
DHCP Client on a Management Interfa
Page 105 and 106:
FIP Snooping 8 FIP snooping is auto
Page 107 and 108:
Figure 8-1. FIP discovery and login
Page 109 and 110:
The following sections describe how
Page 111 and 112:
FIP Snooping Prerequisites On an Ag
Page 113 and 114:
Figure 8-3. show fip-snooping sessi
Page 115 and 116:
Figure 8-7. show fip-snooping stati
Page 117 and 118:
Table 8-5. show fip-snooping statis
Page 119 and 120:
FIP Snooping Example Figure 8-11 sh
Page 121 and 122:
Internet Group Management Protocol
Page 123 and 124:
IGMP Version 3 Conceptually, IGMP v
Page 125 and 126:
Leaving and Staying in Groups Figur
Page 127 and 128:
Figure 9-6. show ip igmp groups Com
Page 129 and 130:
Interfaces 10 This chapter describe
Page 131 and 132:
Viewing Interface Information You c
Page 133 and 134:
Disabling and Re-enabling a Physica
Page 135 and 136: The Aggregator supports the managem
Page 137 and 138: Configuring a Static Route for a Ma
Page 139 and 140: Port-Based VLANs Port-based VLANs a
Page 141 and 142: Displaying VLAN Membership To view
Page 143 and 144: Adding an Interface to an Untagged
Page 145 and 146: Port channels can contain a mix of
Page 147 and 148: Figure 10-12. show interface port-c
Page 149 and 150: Create a Multiple-Range Figure 10-1
Page 151 and 152: Maintenance Using TDR The time doma
Page 153 and 154: MTU Size The Aggregator auto-config
Page 155 and 156: Figure 10-19. show interfaces statu
Page 157 and 158: Figure 10-21 shows the auto-negotia
Page 159 and 160: Clearing Interface Counters The cou
Page 161 and 162: iSCSI Optimization 11 An Aggregator
Page 163 and 164: If no iSCSI traffic is detected for
Page 165 and 166: Displaying iSCSI Optimization Infor
Page 167 and 168: Link Aggregation The Aggregator aut
Page 169 and 170: LACP Example Figure 12-1 shows an e
Page 171 and 172: Figure 12-3. show lacp 128 Command
Page 173 and 174: Figure 12-5. show interfaces port-c
Page 175 and 176: Layer 2 The Aggregator supports CLI
Page 177 and 178: Figure 13-1. Redundant NICs with NI
Page 179 and 180: Link Layer Discovery Protocol (LLDP
Page 181 and 182: Organizationally Specific TLVs Orga
Page 183 and 184: TIA Organizationally Specific TLVs
Page 185: LLDP-MED Network Policies TLV A net
Page 189 and 190: Figure 14-10. Viewing All Informati
Page 191 and 192: Debugging LLDP The debug lldp comma
Page 193 and 194: Table 14-8. LLDP System MIB Objects
Page 195 and 196: Table 14-10. LLDP-MED System MIB Ob
Page 197 and 198: Port Monitoring 15 The Aggregator s
Page 199 and 200: Figure 15-2 shows ports 0/25 and 0/
Page 201 and 202: In Figure 15-4, the host and server
Page 203 and 204: 16 Simple Network Management Protoc
Page 205 and 206: Dell Force10 supports RFC 4001, Tex
Page 207 and 208: Figure 16-6 shows the output for an
Page 209 and 210: Use dot3aCurAggFdbTable to fetch th
Page 211 and 212: Monitor Port-channels To check the
Page 213 and 214: The status of the MIBS is as follow
Page 215 and 216: Stacking Overview 17 An Aggregator
Page 217 and 218: Stack Master Election The stack ele
Page 219 and 220: Stacking Port Numbers By default, e
Page 221 and 222: Cabling Procedure The following cab
Page 223 and 224: Resetting a Unit on a Stack Use the
Page 225 and 226: Figure 17-19. show system Command E
Page 227 and 228: Troubleshooting a Switch Stack Trou
Page 229 and 230: Figure 17-27. show hardware stack-u
Page 231 and 232: Stack Unit in Card-Problem State Du
Page 233 and 234: Upgrading a Single Stack Unit Upgra
Page 235 and 236: Broadcast Storm Control 18 On the A
Page 237 and 238:
System Time and Date 19 The Aggrega
Page 239 and 240:
Setting the Time Zone Universal tim
Page 241 and 242:
Setting Recurring Daylight Saving T
Page 243 and 244:
Uplink Failure Detection (UFD) Upli
Page 245 and 246:
Figure 20-2. Uplink Failure Detecti
Page 247 and 248:
Show Command Syntax Description sho
Page 249 and 250:
Debugging UFD on an Interface To en
Page 251 and 252:
Upgrade Procedures 21 To view the r
Page 253 and 254:
Debugging and Diagnostics The chapt
Page 255 and 256:
Broadcast, unknown multicast, and D
Page 257 and 258:
Auto-configured VLANs do not exist
Page 259 and 260:
Figure 22-2. show system stack-unit
Page 261 and 262:
Figure 22-3. Taking a Stack Unit Of
Page 263 and 264:
Table 22-2. show hardware Commands
Page 265 and 266:
Recognize an Over-Temperature Condi
Page 267 and 268:
The simple network management proto
Page 269 and 270:
Deciding to Tune Buffers Dell Force
Page 271 and 272:
Figure 22-11. Displaying Buffer Pro
Page 273 and 274:
Sample Buffer Profile Configuration
Page 275 and 276:
Figure 22-14. Displaying Buffer Sta
Page 277 and 278:
Displaying Stack Port Statistics Th
Page 279 and 280:
Figure 22-19. Mini application core
Page 281 and 282:
Standards Compliance This chapter c
Page 283 and 284:
General IPv4 Protocols RFC# Full Na
Page 285 and 286:
Network Management (continued) RFC#
show all

8.3.17.0 - Force10 Networks

Create successful ePaper yourself

Delete template?

Save as template?