8.3.17.0 - Force10 Networks

More documents

Recommendations

Info

www.dell.com | support.dell.com Figure 3-9. Filtering Command Outputs with the grep Command FTOS(conf)#do show stack-unit all stack-ports all pfc details | grep 0 stack unit 0 stack-port all 0 Pause Tx pkts, 0 Pause Rx pkts 0 Pause Tx pkts, 0 Pause Rx pkts 0 Pause Tx pkts, 0 Pause Rx pkts 0 Pause Tx pkts, 0 Pause Rx pkts 0 Pause Tx pkts, 0 Pause Rx pkts 0 Pause Tx pkts, 0 Pause Rx pkts Note: FTOS accepts a space or no space before and after the pipe. To filter on a phrase with spaces, underscores, or ranges, enclose the phrase with double quotation marks. • except displays text that does not match the specified text. Figure 3-10 shows this command used in combination with the do show stack-unit all stack-ports all pfc details | except 0 command. Figure 3-10. Filtering Command Outputs with the except Command FTOS(conf)#do show stack-unit all stack-ports all pfc details | except 0 • find displays the output of the show command beginning from the first occurrence of specified text Figure 3-11 shows this command. Figure 3-11. Filtering Command Outputs with the find Command • no-more displays the output all at once rather than one screen at a time. This is similar to the terminal length command except that the no-more option affects the output of the specified command only. • save copies the output to a file for future reference. Note: You can filter a single command output multiple times. The save option should be the last option entered. For example: FTOS# command | grep regular-expression | except regular-expression | grep other-regular-expression | find regular-expression | save 16 | Configuration Fundamentals Admin mode is On Admin is enabled Local is enabled Link Delay 45556 pause quantum stack unit 1 stack-port all Admin mode is On Admin is enabled FTOS(conf)#do show stack-unit all stack-ports all pfc details | find 0 stack unit 0 stack-port all Admin mode is On Admin is enabled Local is enabled Link Delay 45556 pause quantum 0 Pause Tx pkts, 0 Pause Rx pkts stack unit 1 stack-port all
Multiple Users in Configuration Mode FTOS notifies all users in the event that there are multiple users logged into CONFIGURATION mode. A warning message indicates the username, type of connection (console or vty), and in the case of a vty connection, the IP address of the terminal on which the connection was established. For example: • On the system that telnets into the switch, Message 1 appears: Message 1 Multiple Users in Configuration Mode Telnet Message % Warning: The following users are currently configuring the system: User "" on line console0 • On the system that is connected over the console, Message 2 appears: Message 2 Multiple Users in Configuration Mode Telnet Message % Warning: User "" on line vty0 "10.11.130.2" is in configuration mode If either of these messages appear, Dell <strong>Force10</strong> recommends coordinating with the users listed in the message so that you do not unintentionally overwrite each other’s configuration changes. Configuration Fundamentals | 17
Page 1 and 2: Dell PowerEdge Configuration Guide
Page 3 and 4: October 2012 | iii
Page 5 and 6: 1 About this Guide . . . . . . . .
Page 7 and 8: Data Center Bridging Exchange Proto
Page 9 and 10: Displaying VLAN Membership . . . .
Page 11 and 12: Read Managed Object Values . . . .
Page 13 and 14: Troubleshooting Packet Loss . . . .
Page 15 and 16: About this Guide Objectives 1 This
Page 17 and 18: Before You Start Default Settings 2
Page 19 and 20: DCB Support DCB enhancements for da
Page 21 and 22: The untagged VLAN of a server-facin
Page 23 and 24: Configuration Fundamentals 3 The De
Page 25 and 26: Navigating CLI Modes The FTOS promp
Page 27 and 28: Figure 3-5. Undoing a command with
Page 29: Table 3-2. Short-Cut Keys and their
Page 33 and 34: Getting Started This chapter contai
Page 35 and 36: Uplink Ports Ports 33 to 56 are ext
Page 37 and 38: Step Task (continued) Note: Termina
Page 39 and 40: Figure 4-4. Completed Boot Process
Page 41 and 42: Figure 4-6. Completed Boot Process
Page 43 and 44: Access the Aggregator Remotely Conf
Page 45 and 46: Dell Force10 recommends using the e
Page 47 and 48: Figure 4-10 shows an example of usi
Page 49 and 50: To view the contents of a file, fol
Page 51 and 52: Figure 4-14. Alternative Storage Lo
Page 53 and 54: Aggregator Management This chapter
Page 55 and 56: Changing System Logging Settings Yo
Page 57 and 58: Configuring a UNIX Logging Facility
Page 59 and 60: Enabling the FTP Server To enable t
Page 61 and 62: Recovering from a Forgotten Passwor
Page 63 and 64: Figure 5-5. Recovering from a Faile
Page 65 and 66: Data Center Bridging (DCB) 6 On an
Page 67 and 68: Figure 6-1. Priority-Based Flow Con
Page 69 and 70: Data Center Bridging Exchange Proto
Page 71 and 72: QoS dot1p Traffic Classification an
Page 73 and 74: How Enhanced Transmission Selection
Page 75 and 76: DCB Policies in a Switch Stack A DC
Page 77 and 78: Note: On a DCBX port, application p
Page 79 and 80: Auto-Detection of the DCBX Version
Page 81 and 82:
DCBX Error Messages An error in DCB
Page 83 and 84:
Figure 6-7. show interfaces pfc sum
Page 85 and 86:
Table 6-3. show interface pfc summa
Page 87 and 88:
Table 6-4. show interface ets detai
Page 89 and 90:
Figure 6-12. show interface dcbx de
Page 91 and 92:
Example: PFC and ETS Operation This
Page 93 and 94:
Table 6-8. Example: priority group-
Page 95 and 96:
Skippy812 Dynamic Host Configuratio
Page 97 and 98:
Assigning an IP Address Using DHCP
Page 99 and 100:
Releasing and Renewing DHCP-based I
Page 101 and 102:
Figure 7-5. DHCP Client: Debug Mess
Page 103 and 104:
DHCP Client on a Management Interfa
Page 105 and 106:
FIP Snooping 8 FIP snooping is auto
Page 107 and 108:
Figure 8-1. FIP discovery and login
Page 109 and 110:
The following sections describe how
Page 111 and 112:
FIP Snooping Prerequisites On an Ag
Page 113 and 114:
Figure 8-3. show fip-snooping sessi
Page 115 and 116:
Figure 8-7. show fip-snooping stati
Page 117 and 118:
Table 8-5. show fip-snooping statis
Page 119 and 120:
FIP Snooping Example Figure 8-11 sh
Page 121 and 122:
Internet Group Management Protocol
Page 123 and 124:
IGMP Version 3 Conceptually, IGMP v
Page 125 and 126:
Leaving and Staying in Groups Figur
Page 127 and 128:
Figure 9-6. show ip igmp groups Com
Page 129 and 130:
Interfaces 10 This chapter describe
Page 131 and 132:
Viewing Interface Information You c
Page 133 and 134:
Disabling and Re-enabling a Physica
Page 135 and 136:
The Aggregator supports the managem
Page 137 and 138:
Configuring a Static Route for a Ma
Page 139 and 140:
Port-Based VLANs Port-based VLANs a
Page 141 and 142:
Displaying VLAN Membership To view
Page 143 and 144:
Adding an Interface to an Untagged
Page 145 and 146:
Port channels can contain a mix of
Page 147 and 148:
Figure 10-12. show interface port-c
Page 149 and 150:
Create a Multiple-Range Figure 10-1
Page 151 and 152:
Maintenance Using TDR The time doma
Page 153 and 154:
MTU Size The Aggregator auto-config
Page 155 and 156:
Figure 10-19. show interfaces statu
Page 157 and 158:
Figure 10-21 shows the auto-negotia
Page 159 and 160:
Clearing Interface Counters The cou
Page 161 and 162:
iSCSI Optimization 11 An Aggregator
Page 163 and 164:
If no iSCSI traffic is detected for
Page 165 and 166:
Displaying iSCSI Optimization Infor
Page 167 and 168:
Link Aggregation The Aggregator aut
Page 169 and 170:
LACP Example Figure 12-1 shows an e
Page 171 and 172:
Figure 12-3. show lacp 128 Command
Page 173 and 174:
Figure 12-5. show interfaces port-c
Page 175 and 176:
Layer 2 The Aggregator supports CLI
Page 177 and 178:
Figure 13-1. Redundant NICs with NI
Page 179 and 180:
Link Layer Discovery Protocol (LLDP
Page 181 and 182:
Organizationally Specific TLVs Orga
Page 183 and 184:
TIA Organizationally Specific TLVs
Page 185 and 186:
LLDP-MED Network Policies TLV A net
Page 187 and 188:
LLDP Operation On an Aggregator, LL
Page 189 and 190:
Figure 14-10. Viewing All Informati
Page 191 and 192:
Debugging LLDP The debug lldp comma
Page 193 and 194:
Table 14-8. LLDP System MIB Objects
Page 195 and 196:
Table 14-10. LLDP-MED System MIB Ob
Page 197 and 198:
Port Monitoring 15 The Aggregator s
Page 199 and 200:
Figure 15-2 shows ports 0/25 and 0/
Page 201 and 202:
In Figure 15-4, the host and server
Page 203 and 204:
16 Simple Network Management Protoc
Page 205 and 206:
Dell Force10 supports RFC 4001, Tex
Page 207 and 208:
Figure 16-6 shows the output for an
Page 209 and 210:
Use dot3aCurAggFdbTable to fetch th
Page 211 and 212:
Monitor Port-channels To check the
Page 213 and 214:
The status of the MIBS is as follow
Page 215 and 216:
Stacking Overview 17 An Aggregator
Page 217 and 218:
Stack Master Election The stack ele
Page 219 and 220:
Stacking Port Numbers By default, e
Page 221 and 222:
Cabling Procedure The following cab
Page 223 and 224:
Resetting a Unit on a Stack Use the
Page 225 and 226:
Figure 17-19. show system Command E
Page 227 and 228:
Troubleshooting a Switch Stack Trou
Page 229 and 230:
Figure 17-27. show hardware stack-u
Page 231 and 232:
Stack Unit in Card-Problem State Du
Page 233 and 234:
Upgrading a Single Stack Unit Upgra
Page 235 and 236:
Broadcast Storm Control 18 On the A
Page 237 and 238:
System Time and Date 19 The Aggrega
Page 239 and 240:
Setting the Time Zone Universal tim
Page 241 and 242:
Setting Recurring Daylight Saving T
Page 243 and 244:
Uplink Failure Detection (UFD) Upli
Page 245 and 246:
Figure 20-2. Uplink Failure Detecti
Page 247 and 248:
Show Command Syntax Description sho
Page 249 and 250:
Debugging UFD on an Interface To en
Page 251 and 252:
Upgrade Procedures 21 To view the r
Page 253 and 254:
Debugging and Diagnostics The chapt
Page 255 and 256:
Broadcast, unknown multicast, and D
Page 257 and 258:
Auto-configured VLANs do not exist
Page 259 and 260:
Figure 22-2. show system stack-unit
Page 261 and 262:
Figure 22-3. Taking a Stack Unit Of
Page 263 and 264:
Table 22-2. show hardware Commands
Page 265 and 266:
Recognize an Over-Temperature Condi
Page 267 and 268:
The simple network management proto
Page 269 and 270:
Deciding to Tune Buffers Dell Force
Page 271 and 272:
Figure 22-11. Displaying Buffer Pro
Page 273 and 274:
Sample Buffer Profile Configuration
Page 275 and 276:
Figure 22-14. Displaying Buffer Sta
Page 277 and 278:
Displaying Stack Port Statistics Th
Page 279 and 280:
Figure 22-19. Mini application core
Page 281 and 282:
Standards Compliance This chapter c
Page 283 and 284:
General IPv4 Protocols RFC# Full Na
Page 285 and 286:
Network Management (continued) RFC#
show all

8.3.17.0 - Force10 Networks

Create successful ePaper yourself

Delete template?

Save as template?