2006 LSSV Owner's Manual Supplement (PDF) - GM Fleet

More documents

Recommendations

Info

Repeat programming steps 2-7 until Low-Pressure warning levels are set for all axles as desired. 8. Press the SET button to exit. 9. Press the SET button again to revert to normal view. Pressure Deviation Alert This function sets the pressure deviation alert threshold for all tires. Factory default setting is 5 PSI (0.34 Bar). To Program 1. Enter Level 1 Programming Mode, see Entering Programming Mode. 4. Press the TIRE button to increase the value. 5. Press the MODE button to decrease the value. 6. To disable this feature press the MODE button until the display shows OFF. 7. Press the SET button to save when the desired value is reached. 8. Press the SET button twice to revert to normal view. 2. To enter this function press the MODE button until the flat tire icon and pressure units are displayed. 3. Press the TIRE button to scroll to the desired axle. The tires of the selected axle are filled in. 5-41
Temperature Compensated Pressure When a tire heats up, the air pressure inside the tire can also be expected to increase. For example, a normal or “required” pressure at 64°F (18°C) may be 34 PSI or (2.34 Bar) and a normal pressure at 120°F (49°C) may be 39 PSI (2.70 Bar). Both pressure readings are correct at their respective temperatures. The amount of deviation from the required pressure at any temperature can be read by using the Pressure Deviation mode of this system. If at any time you are uncertain that the Actual Pressure reading on the gage display indicates the correct tire pressure, switch to the Pressure Deviation (+) - readout. A blank display indicates that the reading on the display is the correct one. Any (+) or (-) value indicates the tire pressure is incorrect by that value. This value can then be used to correctly inflate the tire. High Temperature Alert This function changes the high-temperature alert threshold. Factory default setting is 176°F (80°C). To Program 1. Enter Level 1 Programming Mode see Entering Programming Mode. 2. To enter this function press the MODE button until the alert icon and temperature units are displayed. 3. Press the TIRE button to enter and display the current value of High Temperature Alert. 4. Press the TIRE button to increase the value. 5. Press the MODE button to decrease the value. 5-42
Page 2 and 3:
2006 General Motors Light Service S
Page 4 and 5:
Safety Warnings and Symbols You wil
Page 6 and 7:
Section 1 Seats and Restraints Troo
Page 8 and 9:
2. Place the pin in the hole provid
Page 10 and 11:
Section 2 Features and Controls Win
Page 12 and 13:
Starting and Operating Your Vehicle
Page 14 and 15:
Storage Areas Cargo Cover The vehic
Page 16 and 17:
13. Secure the bows in place with t
Page 18 and 19:
2. Place the barrel into the upper
Page 20 and 21:
Section 3 Instrument Panel Instrume
Page 22 and 23:
The main components of your instrum
Page 24 and 25:
Blackout Drive Light Control The sw
Page 26 and 27:
Interior Lamp or Device Instrument
Page 28 and 29:
Warning Lights, Gages and Indicator
Page 30 and 31:
Air Filter Restriction Indicator Ti
Page 32 and 33:
Section 4 Driving Your Vehicle Your
Page 34 and 35: vehicle dimensions (A). For actual
Page 36 and 37: Receiver Extension The receiver ext
Page 38 and 39: Recovery Loops Front of the Vehicle
Page 40 and 41: Towing Towing Your Vehicle When tow
Page 42 and 43: Towing a Trailer The vehicle is equ
Page 44 and 45: Section 5 Service and Appearance Ca
Page 46 and 47: Fuel Using JP8 as a Fuel JP8 fuel i
Page 48 and 49: Battery The vehicle may be equipped
Page 50 and 51: 3. Turn off the ignition on both ve
Page 52 and 53: 11. Start the vehicle with the dead
Page 54 and 55: To avoid the possibility of the veh
Page 56 and 57: Note: It may take up to 30 minutes
Page 58 and 59: Engine Control Module (ECM) When ti
Page 60 and 61: tire beads and positively locks the
Page 62 and 63: To open the swing away spare tire c
Page 64 and 65: The following steps apply only to v
Page 66 and 67: 4. Using the wheel wrench and ratch
Page 68 and 69: Place the jack only at the appropri
Page 70 and 71: 13. After mounting the spare, put t
Page 72 and 73: 6. Turn the wheel wrench with the w
Page 74 and 75: 13. Turn the wheel wrench clockwise
Page 76 and 77: Storing a Flat or Spare Tire and To
Page 78 and 79: J (Cold Pressure Indicator): This m
Page 80 and 81: 3. Press SET button to return to no
Page 82 and 83: Tire Pressure Monitor System Progra
Page 86 and 87: 6. To disable this feature press th
Page 88 and 89: Advanced Programming-Level 2 Slope
Page 90 and 91: If more than one tire location cont
Page 92 and 93: Vent Filters Transfer Case The filt
Page 94 and 95: Capacities and Specifications Wheel
Page 96 and 97: Appearance Care Washing Your Vehicl
Page 98 and 99: NOTES 5-55
Page 100 and 101: Section 6 Maintenance Schedule Main
Page 102 and 103: Recommended Fluids and Lubricants F
Page 104 and 105: Date Odometer Reading Serviced By S
Page 106 and 107: NOTES 6-7
Page 108 and 109: Section 7 Customer Assistance Infor
Page 110 and 111: A Accessory Panel Blackout Lighting
Page 112 and 113: L Lamps Exterior...................
Page 114 and 115: U Underbody Protection.............
show all

2006 LSSV Owner's Manual Supplement (PDF) - GM Fleet

Create successful ePaper yourself

Delete template?

Save as template?