download - Knoll
download - Knoll
download - Knoll
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Panel Mounted Worksurface Brackets<br />
Specifications<br />
Dividends Horizon<br />
Worksurface Supports<br />
Worksurfaces are shipped without supports<br />
which must be ordered separately.<br />
A variety of worksurface supports are available.<br />
They include:<br />
<br />
<br />
<br />
In addition, freestanding pedestals and end units<br />
can also be used for worksurface support.<br />
Cantilevers and panel-to-worksurface<br />
brackets are used strictly in panel-mount<br />
applications while flat brackets, pedestals<br />
and end units can be used in both panelmounted<br />
and freestanding applications.<br />
Cantilevers<br />
Cantilevers provide panel-hung worksurface<br />
support when the worksurface width<br />
runs parallel to the panel run.<br />
Primary cantilever applications include:<br />
<br />
<br />
<br />
support in moderate load situations<br />
Note: For heavy load applications, panel-toworksurface<br />
brackets, freestanding pedestal,<br />
panel-mount C-leg, or open support leg<br />
is recommended. In applications involving<br />
30" deep worksurfaces, cantilevers are only<br />
recommended for mid-span support.<br />
Cantilevers are left- and right-handed and are<br />
available in three depths (18", 24" and 30") to<br />
support 18", 24" and 30" deep worksurfaces.<br />
Note: 36" deep worksurfaces cannot be<br />
supported by cantilevers.<br />
Attachment: Cantilevers lock into the panel’s<br />
slotted standard and adjust vertically in 1 1 / 2"<br />
increments. Cantilevers are left- or right-handed<br />
Construction: 14-gauge, black painted steel<br />
Flat Brackets<br />
Flat brackets are used to join a primary<br />
worksurface with an adjacent return or bridge<br />
unit worksurface at the same height.<br />
Flat brackets are available in three<br />
depths to support 18", 24" and 30"<br />
deep worksurface returns.<br />
Attachment: Flat brackets attach to<br />
pre-drilled positions on the undersides of<br />
worksur-faces with provided screws<br />
Construction: 14-gauge painted steel<br />
Shared Cantilevers<br />
Adjacent worksurfaces can share a single<br />
cantilever if the appropriate flat bracket is used<br />
in conjunction with the appropriate cantilever<br />
(i.e. 18" cantilever with 18" flat bracket).<br />
Panel-to-Worksurface Brackets,<br />
Worksurface Support<br />
Panel-to-worksurface brackets are used to:<br />
<br />
<br />
worksurfaces to panels<br />
<br />
Panel-to-worksurface brackets provide the<br />
most secure panel-hung support for heavily<br />
loaded worksurfaces.<br />
Panel worksurface brackets are handed left or right.<br />
Note: The panel width must match the worksurface<br />
depth for panel-to-worksurface brackets to<br />
connect worksurfaces perpendicular to panels.<br />
Attachment: Panel-to-worksurface brackets<br />
lock into the panel’s slotted standard and<br />
adjust vertically in 1 1 / 2" increments<br />
Construction: 14-gauge painted steel<br />
Panel-to-Worksurface Brackets,<br />
Stabilizing Support<br />
Panel-to-worksurface brackets are also used in<br />
conjunction with pedestals to stabilize panel runs.<br />
In applications where the worksurface is<br />
‘‘wrapped’’ with a return panel and a pedestal<br />
is installed below the worksurface at the<br />
‘‘wrapped’’ end, a panel-to-worksurface bracket<br />
is used at the front corner of the worksurface. In<br />
pedestal applications, the panel-to-worksurface<br />
bracket connects the pedestal at the rear corner<br />
of the pedestal to the panel (as shown in the<br />
illustration below) or front corner of the pedestal<br />
to the panel when a return wing panel is used.<br />
Panel-to-Worksurface Brackets,<br />
Off-Module Support<br />
For applications where the width of the panel<br />
exceeds the depth of the worksurface, specify<br />
off-module panel-to-worksurface brackets<br />
which allow off module worksurface support.<br />
Worksurface Reinforcement<br />
Worksurface reinforcements are required for<br />
worksurface spans greater than 48 inches. This<br />
includes freestanding desk worksurfaces over<br />
48 inches using desk end units. Worksurface<br />
reinforcements have a black paint finish.<br />
Panel Mounted Worksurface Bracket Application<br />
Flat Bracket Application<br />
Off-Module Support<br />
Shared Cantilever Application<br />
Worksurface<br />
Reinforcement Panel<br />
Hung Application<br />
Stabilizing Support<br />
322