technical manual for sailor compact hf ssb t2130 - Gopher Proxy

More documents

Recommendations

Info

3 SERVICE T2130 3.4.5 NOT USED 3.4.6 CONNECTION BOARD (MODULE 6) No hints. 3.4.7 REPLACEMENT OF COMPONENTS When replacing transistors, diodes, resistors, capacitors and similar components you must use a small „pencil“ soldering iron of 30 to 75 Watt rating. The soldering must be per<strong>for</strong>med rapidly to avoid overheating, and the use of a tin sucker is recommended, as otherwise there is a risk that both the components and the printed circuit will be spoiled. After replacement of components look-up the chapter 3.7.2 COMPONENTS REPLACED. 3.4.8 REPLACEMENT OF MODULES If a fault has been found in a module, it may often be worthwhile to replace it and then repair it later on. After replacement of a module look-up the chapter 3.7.1 MODULES REPLACED. PAGE 3-10
3 SERVICE T2130 3.5 PERFORMANCE CHECK All tests are done with an RE2100 connected, and a supply voltage of exactly 24.00V. In the subsections in this section is referred to the following test setup modes: Mode 1: Mode 2: Mode 3: Standby. Receive mode, with aerial connected. 50 ohm dummy load connected to the output of T2130. Jumper 5 is inserted into plug PO2-5 in the TX-processor (3) in the T2130. 50 ohm dummy load connected to the output of the AT2110. PAGE 3-11
Page 1:
TECHNICAL MANUAL FOR SAILOR COMPACT
Page 5 and 6:
T2130 CONTENTS 1 GENERAL INFORMATIO
Page 7:
T2130 CONTENTS 1 GENERAL INFORMATIO
Page 10 and 11:
1 GENERAL INFORMATION T2130 1.3 TEC
Page 12 and 13:
1 GENERAL INFORMATION T2130 1.4 PRI
Page 15: T2130 CONTENTS 2 INSTALLATION MECHA
Page 18 and 19: 2 INSTALLATION MECHANICAL HF SSB TR
Page 54 and 55: T2130 3.7.1 MODULES REPLACED 3-23 3
Page 56 and 57: 3 SERVICE T2130 3.4 TROUBLE SHOOTIN
Page 58 and 59: 3 SERVICE T2130 If the error has ap
Page 60 and 61: 3 SERVICE T2130 3.4.2 OUTPUT FILTER
Page 62 and 63: 3 SERVICE T2130 3.4.4 POWER SUPPLY
Page 66 and 67: 3 SERVICE T2130 3.5.1 POWER AMPLIFI
Page 68 and 69: 3 SERVICE T2130 3.5.3 TX-PROCESSOR
Page 70 and 71: 3 SERVICE T2130 3.5.3.3 RF ON/OFF T
Page 72 and 73: 3 SERVICE T2130 3.5.3.9 TUNE MOTOR
Page 74 and 75: 3 SERVICE T2130 3.5.5 NOT USED 3.5.
Page 76 and 77: 3 SERVICE T2130 IMPORTANT! the inpu
Page 78 and 79: 3 SERVICE T2130 3.7.2 COMPONENTS RE
Page 80 and 81: 3 SERVICE T2130 3.8.12 OUTPUT POWER
Page 82 and 83: 3 SERVICE T2130 SP-22-0 Displays th
Page 84 and 85: 3 SERVICE T2130 Operator: Key: 25 R
Page 86 and 87: 3 SERVICE T2130 SP-33 Adjustment of
Page 89: T2130 CONTENTS 4 MECHANICAL DISASSE
Page 93 and 94: 4 MECHANICAL DISASSEMBLING T2130 4.
Page 95: T2130 CONTENTS 5 CIRCUIT DESCRIPTIO
Page 98 and 99: 5 CIRCUIT DESCRIPTION AND SCHEMATIC
Page 102 and 103: T2130 5 CIRCUIT DESCRIPTION AND SCH
Page 114 and 115:
5 CIRCUIT DESCRIPTION AND SCHEMATIC
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
T2130 5 CIRCUIT DESCRIPTION AND SCH
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
T2130 5 CIRCUIT DESCRIPTION AND SCH
Page 131 and 132:
T2130 6 PARTS LIST HF SSB T2130 MF/
Page 133 and 134:
6 PARTSLIST T2130 POSITION DESCRIPT
Page 135 and 136:
Page 137 and 138:
show all

technical manual for sailor compact hf ssb t2130 - Gopher Proxy

Create successful ePaper yourself

Delete template?

Save as template?