Command Reference - Stollmann

More documents

Recommendations

Info

TA+USBA Command Reference 1.01/06.2007 2. Using the TA+USB Table of the X.29 standard profiles Param Prof 0 Prof 1 Prof 2 Prof 3 Prof 4 Prof 5 Prof 6 Prof 7 Prof90 Prof91 eter 1 0 0 1 0 1 1 0 1 1 0 2 0 0 0 0 0 0 0 1 1 0 3 0 0 2 0 2 2 0 2 126 0 4 5 1 0 20 0 0 4 0 0 20 (5) - - - - - - - - - - 6 69 0 9 0 9 9 0 9 1 0 7 8 0 21 2 21 2 0 21 2 2 8 0 0 0 0 0 0 0 0 0 0 9 0 0 2 0 2 2 0 2 0 0 10 0 0 0 0 0 0 0 0 0 0 (11) - - - - - - - - - - (12) 3 - - - - - - - - - 13 0 0 4 0 0 5 0 4 0 0 14 0 0 0 0 0 0 0 0 0 0 15 0 0 0 0 1 1 0 0 0 0 16 0 0 127 127 127 127 127 127 127 127 17 0 0 24 24 24 24 24 24 24 24 18 0 0 18 18 18 18 18 18 18 18 19 0 2 2 2 2 2 2 2 1 1 20 0 0 0 0 0 0 0 0 0 0 21 0 0 1 0 0 1 1 1 0 0 22 0 0 0 0 0 0 0 0 0 0 Note: Parameter in Brackets are not implemented or not setup by command profxx. 14 © Stollmann Entwicklungs- und Vertriebs-GmbH
1.01/06.2007 TA+USBA Command Reference 2. Using the TA+USB 2.2 AT command set All parameter can be changed by using an extended AT command set described in this chapter. Please check if the factory setting will fit with your environment. The factory setting is described (highlighted) in the parameter list shown in chapter "AT command set" (see below). If you want another configuration as set in the factory default setting, please do the following steps: • Connect the TA+USBA to ISDN interface • Connect the PC's com-port to the DTE interface of the TA+USBA. • Connect the power supply to the mains socket. • Start a terminal emulation on your PC, please verify that the baudrate setting of the terminal emulation fits those of the TA+USBA. • Set up the parameter of the TA+USBA from the terminal emulation and save the parameter using the AT command set. Example: To change the used B channel protocol to X.75 please enter the following commands: ATB10 (set protocol to X.75) AT&W (save the new configuration) • Leave your terminal emulation and start your application program. With the exception of the command A/ (Repeat command) all commands begin with the prefix AT and are terminated with . Corrections in a command line are done with . A command line has a maximum of 80 characters (up to 140 characters using “UUS1”. The command line is automatically cancelled by longer input. Blanks are ignored, capital/small letters are not significant. The parameter settings of the TA+USBA obtained when using the AT commands can be permanently stored (AT&W) and are not lost by resetting or by leaving the AT command mode. © Stollmann Entwicklungs- und Vertriebs-GmbH 15
Page 1 and 2: TA+USBA Command Reference ISDN Term
Page 3 and 4: 1.01/06.2007 TA+USBA Command Refere
Page 15: 1.01/06.2007 TA+USBA Command Refere
Page 67 and 68:
1.01/06.2007 TA+USBA Command Refere
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
show all

Command Reference - Stollmann

Create successful ePaper yourself

Delete template?

Save as template?