Command Reference - Stollmann

More documents

Recommendations

Info

TA+USBA Command Reference 1.01/06.2007 2. Using the TA+USB Note: If autobauding is selected (default) and after powering on the TA+USBA no AT command is entered, a response from the TA (i.e. RING) will be sent with the baudrate 115200 bit/s. CONF Enter TA+Configurator Enters directly into the TA+Configurator, the configuration prompt "#" will be displayed. Leave the TA+Configurator with the command "quit" (or “exit” or “go”). ATCONF Note: During the change between the command sets from "AT command set" to "configuration command set" the serial status line DSR gets inactive. &C DCD control Selects the behavior of the DCD control line from the TA. AT&C TA control line DCD is always ON AT&C1 DCD ON indicates ISDN connection is established and synchronized (default) AT&C2 TA control line DCD follows DTR For nearer information see also chapter 3.3. #C Received bearer service Shows the bearer service that is received with an incoming call in hexadecimal coding hbhb. The value for hbhb (word) is the CIP value as defined in the CAPI 2.0 specification, also to be found via Stollmann URL http:\\www.stollmann.de. AT#C #C1=hbhb Select bearer service outgoing Selects the bearer service that will be sent with an outgoing call The value for hbhb (word) is the CIP value as defined in the CAPI 2.0 specification (default 0000). Example: an outgoing call as a voice call: AT#C1=0004. Example: an outgoing call as a data call: AT#C1=0002. 18 © Stollmann Entwicklungs- und Vertriebs-GmbH
1.01/06.2007 TA+USBA Command Reference 2. Using the TA+USB #C2=hbhbhbhb Select bearer service incoming Selects the bearer services that can be accepted with an incoming call. The definition of hbhbhbhb (double word) is the CIP mask as defined in the CAPI 2.0 specification (default 00000004). Example: AT#C2=00030012 : Accept analogue incoming calls AT#C2=00000001 : Accept all incoming calls. Note: Before issuing an outgoing call the command AT#C1 has to be set. To use the predefined services please setup factory defaults (AT&F). D Initiate outgoing call Dials the number (D for Dial). The dial modifier "W", ">", "T", ";", "@" can be freely inserted in the dial string; they have no influence on the dial procedure of the TA+USBA. Must be the last command in AT command line. Any character input while the TA is dialing will cancel the dialing procedure. 1. ATD[X[Pxxx(,|-)][R,][N,][G,] [H,] [D] ] CALLEDnumber: ISDN call number for a dialed B channel connection or X.25 number for X.31 D channel X : starting X.25 parameter section P : use packet size xxx for X.25 connection (value from 64 - 2048) The separator after "Pxxx" will allow [ - ] or [ , ] R : request the facility reverse charging G : access to X.25 closed user group O : Outgoing call from X.25 closed user group N : use NUI and password with call setup allowed chars: a-z, A-Z, 0-9. H : set own X.25 number for outgoing calls, (max. length = 15 digits) (overwrites setting of "XNR" configuration command in chapter 4.4.) NOTE: For X.31-D channel calls the configured own X.25 address will be compared with the real X.25 address of the local X.25 access point. In case of different X.25 numbers the X.25 packet handler will use its own configured X.25 number. © Stollmann Entwicklungs- und Vertriebs-GmbH 19
Page 1 and 2: TA+USBA Command Reference ISDN Term
Page 3 and 4: 1.01/06.2007 TA+USBA Command Refere
Page 19: 1.01/06.2007 TA+USBA Command Refere
Page 71 and 72:
1.01/06.2007 TA+USBA Command Refere
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
show all

Command Reference - Stollmann

Create successful ePaper yourself

Delete template?

Save as template?