DOC023.53.80040 sc200 Controller - Hachflow

More documents

Recommendations

Info

Figure 25 Frequency control function 2. Select Display Setup and push ENTER. Option Adjust Order Description View and modify the measurement display order. • See Current Order—View the current display order • Add Measurements—Add selected measurements to the display • Remove Measurements—Remove selected measurements from the display • Reorder List—Select one or more measurements and change their order in the display • See Default Order—View the default display order • Set to Default—Set the display order to the default configuration Note: Some of the above will not be available if no adjustment is possible for that option (e.g. Reorder List and Remove Measurements will not be available if only one measurement is selected for display). Display Contrast Adjust the contrast to a value between the minimum of +1 and the maximum of +9 1 High limit 5 Cycle duration 2 Deadband 6 Time (x-axis) 3 Setpoint 7 Selected source (y-axis) 4 Low limit • Warning Function Option Warning Display setup Description Sets the level for warning activation. Refer to the sensor manual for the numbers for individual warning messages. Configures the controller display. 1. From the Settings menu, select sc200 Setup and push ENTER. Edit Name Assigns a name to the controller Update the date and time 1. From the Settings menu, select sc200 Setup and push ENTER. 2. Select Set Date/Time and push ENTER. 3. Select Date Format from the Set Date/Time screen and push ENTER. 4. Select a format and push ENTER. 5. Select Date/Time from the Set Date/Time screen and push ENTER. 6. Update the entries. a. Use the right and left arrow keys to highlight a field. b. Use the up and down arrow keys to change the values in the field and push ENTER. 36 English
c. At the end of the date field, push the right arrow to wrap down to the time fields. d. Use the up and down and arrow keys to update the time fields. 7. Push ENTER to save the changes. The controller returns to the Set Date/Time menu. Set the datalog mode and interval Datalog Setup is available if a calculation has been set up. 1. From the Settings menu, select sc200 Setup and push ENTER. 2. Select Datalog Setup and push ENTER. 3. Select Set Mode and push ENTER. 4. Select an option (Snap Shot, Average, Maximum, Minimum) and push ENTER. 5. From the Datalog Setup menu, select Set Interval and push ENTER. 6. Select an interval from the list and push ENTER. Set up a calculation 1. From the Settings menu, select sc200 Setup and push ENTER. 2. Select Calculation and push ENTER. Select a menu option and choose from the displayed list or update the entry. Refer to the table below for more information about each option. Option Set variable X Set parameter X Set variable Y Set parameter Y Description Selects the sensor for the x variable Selects the sensor measurement for the x variable Selects the sensor for the y variable Selects the sensor measurement for the y variable Option Set formula Display format Set units Set parameter Description Select the math function to implement: • None—Disables the math function • X-Y—Subtraction function • X+Y—Addition function • X/Y—Division function • [X/Y]%—Percentage function • [X+Y]/2—Average function • [X*Y]—Multiplication function • [X-Y]%/X—Difference function Selects the number of digits and decimal points Selects the units for the calculated reading Selects the parameter for the calculated reading 3. Push ENTER to save the selection or setting and return to the Calculation menu. Set up the discrete inputs Use these inputs to switch closure inputs or logic level voltage inputs. 1. Press the MENU key. 2. Select sc200 Setup and push ENTER. 3. Select Discrete Input Setup and push ENTER. 4. Select the desired channel (Input 1, Input 2 or Input 3) and push ENTER. 5. Select a control logic option and push ENTER. Option Disable Description This channel is disabled and not used. On/High This channel is active when either the switch input is On (or closed), or the logic level voltage input is at a High level. Off/Low This channel is active when either the switch input is Off (or opened), or the logic level voltage input is at a Low level. English 37
Page 1: DOC023.53.80040 sc200 Controller 08
Page 4 and 5: Table of Contents Graphical display
Page 6 and 7: Table of Contents 4
Page 8 and 9: notice or obligation. Revised editi
Page 10 and 11: Relays outputs and signals The cont
Page 12 and 13: Figure 4 Panel mounting dimensions
Page 14 and 15: Figure 7 Wiring connections overvie
Page 16 and 17: 14 English
Page 18 and 19: The 24 VDC controller relays are de
Page 20 and 21: Analog output connections W A R N I
Page 22 and 23: Table 4 Input connections (continue
Page 24 and 25: Inputs and outputs are set up and c
Page 26 and 27: Option Description Advanced operati
Page 28 and 29: Outputs for analog output modules a
Page 30 and 31: Logarithmic output mode Figure 15 s
Page 32 and 33: • Alarm Function (refer to Figure
Page 34 and 35: Figure 20 Feeder control function (
Page 36 and 37: Figure 23 Event control function (O
Page 40 and 41: 6. Select a warning option and push
Page 42 and 43: 6. Allow time for the files to tran
Page 44 and 45: DataCom is used to upload software
Page 46 and 47: Problem Sensor not recognized Note:
Page 48: Description Item number Description

DOC023.53.80040 sc200 Controller - Hachflow

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?