DOC023.53.80040 sc200 Controller - Hachflow

More documents

Recommendations

Info

notice or obligation. Revised editions are found on the manufacturer’s website. Safety information N O T I C E The manufacturer is not responsible for any damages due to misapplication or misuse of this product including, without limitation, direct, incidental and consequential damages, and disclaims such damages to the full extent permitted under applicable law. The user is solely responsible to identify critical application risks and install appropriate mechanisms to protect processes during a possible equipment malfunction. Please read this entire manual before unpacking, setting up or operating this equipment. Pay attention to all danger and caution statements. Failure to do so could result in serious injury to the operator or damage to the equipment. Make sure that the protection provided by this equipment is not impaired. Do not use or install this equipment in any manner other than that specified in this manual. Use of hazard information D A N G E R Indicates a potentially or imminently hazardous situation which, if not avoided, will result in death or serious injury. W A R N I N G Indicates a potentially or imminently hazardous situation which, if not avoided, could result in death or serious injury. C A U T I O N Indicates a potentially hazardous situation that may result in minor or moderate injury. N O T I C E Indicates a situation which, if not avoided, may cause damage to the instrument. Information that requires special emphasis. Precautionary labels Read all labels and tags attached to the instrument. Personal injury or damage to the instrument could occur if not observed. A symbol on the instrument is referenced in the manual with a precautionary statement. Certification This symbol, if noted on the instrument, references the instruction manual for operation and/or safety information. This symbol indicates that a risk of electrical shock and/or electrocution exists. This symbol indicates the presence of devices sensitive to Electrostatic Discharge (ESD) and indicates that care must be taken to prevent damage with the equipment. Electrical equipment marked with this symbol may not be disposed of in European public disposal systems after 12 August of 2005. In conformity with European local and national regulations (EU Directive 2002/96/EC), European electrical equipment users must now return old or end-of-life equipment to the Producer for disposal at no charge to the user. Canadian Radio Interference-Causing Equipment Regulation, IECS-003, Class A: Supporting test records reside with the manufacturer. This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numèrique de la classe A respecte toutes les exigences du Rëglement sur le matériel brouilleur du Canada. FCC Part 15, Class "A" Limits Supporting test records reside with the manufacturer. The device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 6 English
1. The equipment may not cause harmful interference. 2. The equipment must accept any interference received, including interference that may cause undesired operation. Figure 1 System components Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at their expense. The following techniques can be used to reduce interference problems: 1. Disconnect the equipment from its power source to verify that it is or is not the source of the interference. 2. If the equipment is connected to the same outlet as the device experiencing interference, connect the equipment to a different outlet. 3. Move the equipment away from the device receiving the interference. 4. Reposition the receiving antenna for the device receiving the interference. 5. Try combinations of the above. Product overview The controller displays sensor measurements and other data, can transmit analog and digital signals, and can interact with and control other devices through outputs and relays. Outputs, relays, sensors and sensor modules are configured and calibrated through the user interface on the front of the controller. Figure 1 shows the product components. Components may vary according to controller configuration. Contact the manufacturer if parts are damaged or missing. 1 <strong>Controller</strong> 4 Network module (optional) 2 Strain relief assembly (optional depending on controller version) 3 Digital connection fitting (optional depending on controller version) 5 High-voltage barrier 6 Sensor modules (optional) Sensors and sensor modules The controller accepts up to a maximum of two sensor modules or two digital sensors (depending on the controller configuration), along with one communication module. A single digital sensor and a single sensor module can be installed in combination. A variety of sensors can be wired to the sensor modules. Sensor wiring information is given in the specific sensor manuals and in the user instructions for specific modules. English 7
Page 1: DOC023.53.80040 sc200 Controller 08
Page 4 and 5: Table of Contents Graphical display
Page 6 and 7: Table of Contents 4
Page 10 and 11: Relays outputs and signals The cont
Page 12 and 13: Figure 4 Panel mounting dimensions
Page 14 and 15: Figure 7 Wiring connections overvie
Page 16 and 17: 14 English
Page 18 and 19: The 24 VDC controller relays are de
Page 20 and 21: Analog output connections W A R N I
Page 22 and 23: Table 4 Input connections (continue
Page 24 and 25: Inputs and outputs are set up and c
Page 26 and 27: Option Description Advanced operati
Page 28 and 29: Outputs for analog output modules a
Page 30 and 31: Logarithmic output mode Figure 15 s
Page 32 and 33: • Alarm Function (refer to Figure
Page 34 and 35: Figure 20 Feeder control function (
Page 36 and 37: Figure 23 Event control function (O
Page 38 and 39: Figure 25 Frequency control functio
Page 40 and 41: 6. Select a warning option and push
Page 42 and 43: 6. Allow time for the files to tran
Page 44 and 45: DataCom is used to upload software
Page 46 and 47: Problem Sensor not recognized Note:
Page 48: Description Item number Description

DOC023.53.80040 sc200 Controller - Hachflow

Create successful ePaper yourself

Delete template?

Save as template?