Sound - Denon-DN-M1050R-manual - SXS Events

More documents

Recommendations

Info

(9) Incrementing Track Numbersvent courtesy production Phone: of and 0870 Audio-Visual 080 2342Start of recording ServicesDuring recording, track numbers can be incremented eitherCD/MDTrack1 2 3•www.sxsevents.co.ukTrack email: numbers can be incremented enquiries@sxsevents.co.ukmanually in the followingTrack X Track Y Track Zfour ways:Copy1) Press the REC button (●) during recording. This incrementsStart of recordingEnd of recordingthe track number.Track2) Press the PLAY/PAUSE button (13) during recording toMD number 1 2 3 4 5stop recording for that track number and set the recordingTrack A Track B Track X Track Y Track Zpause mode. When the PLAY/PAUSE button (13) ispressed again, recording starts with a new track number.Previously recordedtracksTracks recordedfrom the CD (MD)3) Press the STOP button (2) during recording to stoprecording for that track number and set the stop mode.Now set the recording mode again. Recording starts with anew track number.4) After recording, use the divide function.• Track numbers can be incremented automatically in thefollowing three ways, according to the type of input signal:Input typeMethodAnalog/digital input Detection of soundless section 1)Digital inputCDsandMDsDATsDetection of soundless section 1)Using the CD’s or MD’s subcodes 2)Detection of soundless section 1)Using the DAT’s start IDs 3)1) Detection of soundless sectionI Make the following two presettings:• Set “Auto Inc OFF” (4) to “Auto Inc Det.”• Set the soundless detection level setting to “Inc. Det.-(60)dB” (5).II Start playback and recording in such a way that the beginningof the sound is not missed. When a soundless section (or asection with level lower than the preset soundless detectionlevel setting) of at least 2 continuous seconds is detected, thedisc’s track number is automatically incremented.Input signalSoundless section2 seconds or moreTrack number is incrementedNOTE: The auto track increment function may not work whenrecording analog signals containing much noise. In this caselower the detection level to for example –54 dB.2) Using the CD’s or MD’s subcodes (digital input)I Make the following presetting:• Set “Auto Inc OFF” (4) to “Auto Inc Dig.”.II Start playback on the CD (MD) player and recording on therecorder in such a way that the beginning of the sound is notmissed. The disc’s track number is automatically incrementedwhen the CD’s (MD’s) track number changes. Changes in theCD’s (MD’s) track number will not be detected forapproximately 4 seconds after the track number isincremented.3) Using the DAT’s start IDs (digital input)I Record the start ID on the recorded DAT.II Make the following presetting:• Set “Auto Inc OFF” (2) to “Auto Inc Dig.”III Start playback on the DAT player and recording on therecorder in such a way that the beginning of the sound is notmissed. The disc’s track number is automatically incrementedwhen the DAT’s start ID is detected. The start ID will not bedetected for 15 seconds after the track number isincremented.DATMDCopyTracknumberStart of recordingTracknumberStart of recording1 2 31 2 3 4 5Track A Track B Track X Track Y Track ZPreviously recordedtracks(10) Pre-UTOC FunctionTrack X Track Y Track ZTracks recordedfrom the DATEnd of recording• Presettings must be set. (Refer to Page 42.)This function protects the recording should the power supply becut off. The UTOC is written directly after recording starts.(The pre-UTOC is written.)Normally the UTOC is written after recording is completed, so ifthe power supply should be cut off during the recording or directlyafter the recording is finished, the recording will not be registeredon the disc. To prevent this, the pre-UTOC (*1) is registered onthe disc directly after recording starts. Once recording iscompleted normally, the actual UTOC (*2) is written. If the powershould be cut before the actual UTOC is written, the disc can beplayed according to the pre-UTOC. This way you neveraccidentally lose recordings that cannot be made over again.Pre-UTOC (*1)UTOC (*2)Entire disc01Tr 02Tr 03Tr01Tr 02Tr 03TrStart of recordingEnd of recordingIf some problem occurs and recording is interrupted, the samerecording and UTOC can be written using the following editingoperation:Use the divide function at the point where recording wasinterrupted in track 03 on the above diagram to divide the track,then use the erase function to erase track 04.ENGLISHNOTE:The auto track increment function using the DAT’s start ID or the CD’s sub codes will not work if the digital input is in professional format(AES/EBU). Input digital signals of the consumer format (SPDIF).When recording from the DN-C680, set the presettings on the DN-C680.www.sxsevents.co.uk17
IENGLISHvent 5courtesy production HANDY OPERATION Phone: of and 0870 Audio-Visual 080 2342Serviceswww.sxsevents.co.ukemail: enquiries@sxsevents.co.uk(1) Starting Playback from the Middle of a Track(Manual Search)1-1• When a track is selected and PLAY/PAUSE button is pressed,playback starts from the beginning of that track. To start from adifferent position in the track, use the procedure describedbelow to find the desired position.Find the play start position.Turn the SEARCH dial.When the SEARCH dial (inner side) isturned, the frame move mode is set. Theplayback position moves one frame foreach click.BackwardForwardWhen the dial is turned clockwise, the playback position movesas follows:Listen to the sound and find the desired play start position.(2) Playing at a Different Speed (Pitch)1-1• Use this function to play discs at different speeds.• The speed can be changed with the range of –9.9 to +9.9%.Set the play speed.(1) To increase the speed:Press the “+” button.IIPITCH %PITCH % PITCH %The speed increases by 0.1% each time the button ispressed. If the button is held in, the speed changescontinuously.(2) To decrease the speed:Press the “–” button.PITCH % PITCH % PITCH %1-2Turn the SCAN dial to change the playback positionquickly.The fast forward/reverse mode is set whenthe SCAN dial (outer side) is turned.The speed changes according to the angleat which the dial is turned.Backward Forward1-2The speed decreases by 0.1% each time the button ispressed. If the button is held in, the speed changescontinuously.To check the play start position:Press the PLAY/PAUSE button.Set the pitch play mode.Press the PITCH button.2PLAY/PAUSEPLAY/PAUSEPlayback starts.2PITCHPITCHLitMonitor the play signal to check the play start position.LitCue the play start position.Press the STANDBY/CUE button.The button lights and the set play speed is set.NOTE: When the PITCH button is lit, the play speed canbe changed by pressing the “+” and “–” buttons.3FlashingLitNOTE:When the play speed (PITCH) is set, the display shows the setpitch, but the disc is played at the standard speed until thePITCH button is pressed (and the button is lit).When the play speed is changed, the sampling frequency of thedigital output signal also changes, so it may not be possible toreceive digital signals.The pickup returns to the play start position and thestandby mode is set.18www.sxsevents.co.uk
Page 1 and 2: Event courtesy production Phone: of
Page 3 and 4: nt production courtesy Phone: SAFET
Page 5 and 6: ENGLISH DEUTSCH FRANCAIS ESPAÑOLve
Page 7 and 8: ENGLISHvent courtesy production Pho
Page 9 and 10: ENGLISHvent production and Audio-Vi
Page 13 and 14: ENGLISHvent 4courtesy production BA
Page 15: ENGLISHvent courtesy production Pho
Page 25 and 26: IIENGLISHvent courtesy production P
Page 27 and 28: ENGLISHvent 7courtesy production ED
Page 33 and 34: PAUSELEVEL STARTRECPRESETPROG. PLAY
Page 35 and 36: PAUSELEVEL STARTRECPRESETPROG. PLAY
Page 37 and 38: POWER¢ ONMIN£ OFFLEVELPHONESMAXST
Page 39 and 40: ENGLISHvent 9courtesy production PR
Page 41 and 42: ENGLISH(3) Detailed Description of
Page 43 and 44: ENGLISHvent 10courtesy production H
Page 45 and 46: ENGLISHvent 13courtesy production S

Sound - Denon-DN-M1050R-manual - SXS Events

Create successful ePaper yourself

Delete template?

Save as template?