SBC81870 SERIES USER'S MANUAL VERSION A1 SEPTEMBER ...

More documents

Recommendations

Info

<strong>SBC81870</strong> Intel ® Pentium ® M w/ DDR/VGA/Dual LANFloppy Disk Cntrlr Error Or No Cntrlr Present:Cannot find or initialize the floppy drive controller. Make surethe controller is installed correctly and firmly. If there are nofloppy drives installed, be sure the Diskette Drive selection inSetup is set to NONE.Invalid Eisa ConfigurationPlease Run Eisa Configuration Utility:The non-volatile memory containing EISA configurationinformation was programmed incorrectly or has become corrupt.Re-run EISA configuration utility to correctly program thememory.Note: When this error appears, the system will boot in ISAmode, which allows you to run the EISA Configuration Utility.Keyboard Error Or No Keyboard Present:Cannot initialize the keyboard. Make sure that the keyboard isproperly attached and no keys being pressed during the boot.If you are purposely configuring the system without a keyboard,set the error halt condition in Setup to HALT ON ALL, BUTKEYBOARD. This will cause the BIOS to ignore the missingkeyboard and continue the boot.Memory Address Error At ... :Indicates a memory address error at a specific location. Youcan use this location along with the memory map for yoursystem to find and replace the bad memory chips.Memory Parity Error At ... :Indicates a memory parity error at a specific location. You canuse this location along with the memory map for your system tofind and replace the bad memory chips.Memory Size Has Changed Since Last Boot:Memory has been added or removed since the last boot. InEISA mode use Configuration Utility to reconfigure the memoryconfiguration. In ISA mode enter Setup and enter the newmemory size in the memory fields.Trouble Shooting 97
<strong>SBC81870</strong> Intel ® Pentium ® M w/ DDR/VGA/Dual LANMemory Verify Error At ... :Indicates an error verifying a value already written to memory.Use the location along with your system's memory map tolocate the bad chip.Offending Address Not Found:This message is used in conjunction with the I/O CHANNELCHECK and RAM PARITY ERROR messages when thesegment that has caused the problem cannot be isolated.Offending Segment:This message is used in conjunction with the I/O CHANNELCHECK and RAM PARITY ERROR messages when thesegment that has caused the problem has been isolated.Press A Key To Reboot:This will be displayed at the bottom screen when an erroroccurs that requires you to reboot. Press any key and thesystem will reboot.Press F1 To Disable Nmi, F2 To Reboot:When BIOS detects a Non-maskable Interrupt condition duringboot, this will allow you to disable the NMI and continue to boot,or you can reboot the system with the NMI enabled.Ram Parity Error – Checking For Segment:Indicates a parity error in Random Access Memory.Should be Empty But EISA Board FoundPlease Run Eisa Configuration Utility:A valid board ID was found in a slot that was configured ashaving no board ID.Note: When this error appears, the system will boot in ISAmode, which allows you to run the EISA Configuration Utility.Should Have EISA Board But Not FoundPlease Run Eisa Configuration Utility:The board installed is not responding to the ID request, or noboard ID has been found in the indicated slot.Note: When this error appears, the system will boot in ISAmode, which allows you to run the EISA Configuration Utility.98Trouble Shooting
Page 2 and 3:
SBC81870 Intel ® Pentium ® M w/ D
Page 4 and 5:
Page 6 and 7:
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53: SBC81870 Intel ® Pentium ® M w/ D
Page 116: SBC81870 Intel ® Pentium ® M w/ D
show all

SBC81870 SERIES USER'S MANUAL VERSION A1 SEPTEMBER ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?