Installation Manual - ICT

More documents

Recommendations

Info

Temporary direct connections can be used for onsite programming by connecting directly to the computerEthernet port.Ethernet 10/100 Direct ConnectionULULČ• All network equipment such as hub/router/gateway used with the Protege System Controller mustcomply with the UL and ULC standard requirements associated with a signal receiving center.• The Protege System Controller must be installed in the same room as the network equipment thatprovides it the network connection.18 PRT-CTRL-SE Protege SE Integrated System Controller Installation Manual | March 2013
5 Door Access ControlThe Controller provides access control functionality onboard without the requirement for additional hardware.With 2 access controlled doors built in, the flexibility of the Protege system is expanded even further. TheController allows the connection of 2 Wiegand devices to control 2 doors (entry or exit only) or can beconfigured in multiplex mode to allow 4 Wiegand devices controlling 2 doors giving the flexibility of entry and exitreaders.5.1 Card Reader ConnectionThe following diagram shows the connection of a standard Wiegand Reader with the Controller controlling anaccess door in entry or exit mode (2 doors, 2 readers).+AUX- Z9 COM Z10 Z11 COM Z12 D0 D1 L1 BZREDShielded CableBLACKGREENWHITEN/RORANGE* See TextN/R = Not RequiredShield is framegrounded atone pointShield notconnectedBROWNBLUEN/RYELLOW*SHIELDCard Reader ConnectionThe card reader must be connected to the Controller port using a shielded cable. Always refer to the cardreader manufacturer for detailed installation guidelines. The shield connection must only be connected at oneend of the cable in the metallic enclosure(frame grounded). The beeper output on the Controller providesdiagnostic information to the end user and installer when access is denied or the unit is operating offline.Warning:• Do not connect the shield to a AUX- or 0V connection.• Do not join the shield and black wires at the reading device.• Do not connect the shield to any shield used for isolated communication.i• If the Controller is used with the expansion connector fitted, the second onboard reader portbecomes unavailable.• The Controller does not support dual LED reader mode and readers must be configured for singleLED mode. Refer to your card reader documentation for further details.ULULČCompatible access control card reader communication formats are: 26-, 34-, 37-Bit Wiegand,RS-232, RS-485, and Smart RS-485.PRT-CTRL-SE Protege SE Integrated System Controller Installation Manual | March 2013 19
Page 1 and 2: PRT-CTRL-SEProtege SE Integrated Sy
Page 3 and 4: Contents1 Introduction ____________
Page 5 and 6: 1 IntroductionThank you for purchas
Page 7 and 8: 3 MountingThe Protege Controller is
Page 9 and 10: +-4 Connections4.1 Protege SE Integ
Page 11 and 12: 4.5 AC PowerThe Protege Controller
Page 13 and 14: 4.7 Battery Charge Current SettingT
Page 15 and 16: ULULČIf an external power supply
Page 17: Warning: Power to the Protege Syste
Page 21 and 22: 5.3 Door Contact ConnectionThe Cont
Page 23 and 24: The default settings are shown in t
Page 25 and 26: Each zone input can use a different
Page 27 and 28: 7 Programmable OutputsThe Controlle
Page 29 and 30: 8 Hardware Configuration8.1 Configu
Page 31 and 32: 9 LED IndicatorsThe Controller incl
Page 33 and 34: 10 Mechanical DiagramThe mechanical
Page 35 and 36: 12 System CapacitiesThe Protege Con
Page 37 and 38: 13 Technical SpecificationsThe foll
Page 39 and 40: 13.2 Current and Validation Example
Page 41 and 42: 13.4 Current and Validation (UL Ins
Page 43 and 44: 14 UL and ULC Installation Requirem
Page 45 and 46: The following options must be enabl
Page 47 and 48: In the ArmorIP Internet Monitoring
Page 49 and 50: CAN/ULC-S559PRT-CTRL-SEPASSIVE COMM
Page 51 and 52: In the event of unsuccessful commun
Page 53 and 54: 15 FCC Compliance StatementsFCC PAR
Page 55 and 56: 16 Industry Canada StatementThis cl
Page 57 and 58: 18 WarrantyIntegrated Control Techn
Page 60: 227-4045-001 : UL 06 March 2013

Installation Manual - ICT

Create successful ePaper yourself

Delete template?

Save as template?