Installation Manual - ICT

More documents

Recommendations

Info

8.2 Defaulting a ControllerThe Controller can be set back to factory default using the following procedures. This resets all internal data andevent information.Step 1Remove power from the controller by disconnecting the AC and battery supply.Step 2Turn ON configuration dip switch 4.Step 3Power up the Controller by turning on the AC supply.Step 4Turn OFF configuration dip switch 4 once the Controller is indicating normal status by flashing the green statusindicator. The system will now be defaulted with all programming and settings returned to factory configuration.iDefaulting the Controller does not reset the IP address. To reset an IP address, refer to the details onthe Configuration Switch (see page 29).30 PRT-CTRL-SE Protege SE Integrated System Controller Installation Manual | March 2013
9 LED IndicatorsThe Controller includes extensive diagnostic indicators that can aid the installer in diagnosing faults andconditions. In some cases an indicator may have multiple meanings depending on the status indicator display.9.1 Status LEDThe Status indicator is located in the centre of the PCB and indicates the status of the Controller. If theController is operating normally the LED will indicate this by flashing at 1 second intervals.9.2 Fault IndicatorThe Fault indicator is located in the centre of the PCB. During normal operation the fault indicator is off. Flashingon will indicate that the Controller is operating in firmware update mode and requires firmware to bedownloaded.9.3 Charge/Test IndicatorThe Charge/Test indicator serves two functions. It indicates that a battery test is in progress and also thatbattery charging is being performed. When AC is present, the battery charging current will be indicated by avarying intensity level on this indicator. This indicator will also illuminate when a battery test is in progress byilluminating brightly for 30 seconds every 10 minutes. The battery test period is a programmable option in theController system options.This LED is identified by the text CHARGE/TEST. This indicator does not function when AC is not present.9.4 Auxiliary OK IndicatorsAuxiliary voltage is supplied to the AUX1 and AUX2 outputs through two separate auxiliary fuses. If auxiliarysupplies are normal, both the AUX1 OK and AUX2 OK indicators will be illuminated.9.5 AC OK IndicatorWhen a valid AC input is provided to the Controller the AC OK indicator will illuminate.9.6 5V Isolated Power IndicatorThe module communicates using an isolated RS-485 interface for optimal performance and this requires anisolated supply on the N+ and N- terminals of the module network interface. When a valid supply is input, the 5VISO indicator will illuminate.PRT-CTRL-SE Protege SE Integrated System Controller Installation Manual | March 2013 31
Page 1 and 2: PRT-CTRL-SEProtege SE Integrated Sy
Page 3 and 4: Contents1 Introduction ____________
Page 5 and 6: 1 IntroductionThank you for purchas
Page 7 and 8: 3 MountingThe Protege Controller is
Page 9 and 10: +-4 Connections4.1 Protege SE Integ
Page 11 and 12: 4.5 AC PowerThe Protege Controller
Page 13 and 14: 4.7 Battery Charge Current SettingT
Page 15 and 16: ULULČIf an external power supply
Page 17 and 18: Warning: Power to the Protege Syste
Page 19 and 20: 5 Door Access ControlThe Controller
Page 21 and 22: 5.3 Door Contact ConnectionThe Cont
Page 23 and 24: The default settings are shown in t
Page 25 and 26: Each zone input can use a different
Page 27 and 28: 7 Programmable OutputsThe Controlle
Page 29: 8 Hardware Configuration8.1 Configu
Page 33 and 34: 10 Mechanical DiagramThe mechanical
Page 35 and 36: 12 System CapacitiesThe Protege Con
Page 37 and 38: 13 Technical SpecificationsThe foll
Page 39 and 40: 13.2 Current and Validation Example
Page 41 and 42: 13.4 Current and Validation (UL Ins
Page 43 and 44: 14 UL and ULC Installation Requirem
Page 45 and 46: The following options must be enabl
Page 47 and 48: In the ArmorIP Internet Monitoring
Page 49 and 50: CAN/ULC-S559PRT-CTRL-SEPASSIVE COMM
Page 51 and 52: In the event of unsuccessful commun
Page 53 and 54: 15 FCC Compliance StatementsFCC PAR
Page 55 and 56: 16 Industry Canada StatementThis cl
Page 57 and 58: 18 WarrantyIntegrated Control Techn
Page 60: 227-4045-001 : UL 06 March 2013

Installation Manual - ICT

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?