Installation Manual - ICT

More documents

Recommendations

Info

CAN/ULC-S559PRT-CTRL-SEACTIVE COMMUNICATIONMetal ConduitNote: All cables shall be protected within metal conduits.ENCLOSUREPRT-CTRL-SE24h Standby / BackupRequired for TelecomEquipmentMARCUS M4758CTHardwire TransformerACACETHERNETTELECOMEQUIPMENTINTERNETFIRE ALARM PANELFIREZ1SUPERVISORYZ2TROUBLEZ3COM STATUS / FBEDWARDSCRCRLRELAYPOS+NEG -AUXP3 or P4Dry Contacts* If installation requires Fire Alarm Panel local supervision, a ULC S527 listed relay module (such as the EDWARDS CRCRL RELAY) must be used to trigger input zone on fire alarm control panel.The relay module must be able to meet supervision requirements of the input zone or be mounted within 18m of the fire alarm control unit in conduit.* Fire zones shall be separated from burglar zones through area partitioning.* Fire zones Z1-Z3 shall be used exclusively for fire monitoring and cannot be programmed to activate bell outputs (B1/B2)Typical Zone CircuitsValue 1 Value 2 Monitored Status1K 1K Open, Close, Tamper, Short6K8 2K2 Open, Close, Tamper, Short10K 10K Open, Close, Tamper, Short2K2 2K2 Open, Close, Tamper, Short4K7 2K2 Open, Close, Tamper, Short4K7 4K7 Open, Close, Tamper, ShortN.CTamperN.C Zone ContactValue 2 Value 1+AUX- Z1 COM COMZ2 Z3 Z4* EOL resistor must be installed at the Fire Alarm Control Panel Output.48 PRT-CTRL-SE Protege SE Integrated System Controller Installation Manual | March 2013
CAN/ULC-S559PRT-CTRL-SEPASSIVE COMMUNICATIONMetal ConduitNote: All cables shall be protected within metal conduits.ENCLOSUREPRT-CTRL-SE24h Standby / BackupRequired for TelecomEquipmentMARCUS M4758CTHardwire TransformerACACETHERNETTELECOMEQUIPMENTINTERNETFIRE ALARM PANELFIREZ1SUPERVISORYZ2DIALERModem InterfaceSurge ProtectorL-Com HGLN-D1DTTELECOMEQUIPMENTPSTNTROUBLEZ3COM STATUS / FBEDWARDSCRCRLRELAYPOS+NEG -AUXP3 or P4Dry Contacts* If installation requires Fire Alarm Panel local supervision, a ULC S527 listed relay module (such as the EDWARDS CRCRL RELAY) must be used to trigger input zone on fire alarm control panel.The relay module must be able to meet supervision requirements of the input zone or be mounted within 18m of the fire alarm control unit in conduit.* Fire zones shall be separated from burglar zones through area partitioning.* Fire zones Z1-Z3 shall be used exclusively for fire monitoring and cannot be programmed to activate bell outputs (B1/B2)Typical Zone CircuitsValue 1 Value 2 Monitored Status1K 1K Open, Close, Tamper, Short6K8 2K2 Open, Close, Tamper, Short10K 10K Open, Close, Tamper, Short2K2 2K2 Open, Close, Tamper, Short4K7 2K2 Open, Close, Tamper, Short4K7 4K7 Open, Close, Tamper, ShortN.CTamperN.C Zone ContactValue 2 Value 1+AUX- Z1 COM COMZ2 Z3 Z4* EOL resistor must be installed at the Fire Alarm Control Panel Output.• Fire Zone Inputs and OutputsFire Zone inputs must be programmed as follow:• FACP Fire Alarm Signal zone type must be programmed as Fire• Supervisory Trouble Signal zone type must be programmed as 24 Hr Silent• Trouble Signal zone type must be programmed as 24 Hr SilentPlease refer to the section Zone Type Alarm Options in the Protege System Controller Reference Manual(227-4045-500)• All fire zone inputs must be placed into an area and this area must be armed. Please refer to the sectionArea in the Protege System Controller Reference Manual (227-4045-500)• COM StatusFACP system with a COM STATUS input must have this input connected to the P3 or P4 output of thepanel and the selected output must be programmed as the Report OK PGM in the Contact ID Service.Please refer to section Report OK PGM Option in the Protege System Controller Reference Manual(227-4045-500).• Fire zones Z1-Z3 shall be used exclusively for fire monitoring and cannot be programmed to activate belloutputs (B1/B2).PRT-CTRL-SE Protege SE Integrated System Controller Installation Manual | March 2013 49
Page 1 and 2: PRT-CTRL-SEProtege SE Integrated Sy
Page 3 and 4: Contents1 Introduction ____________
Page 5 and 6: 1 IntroductionThank you for purchas
Page 7 and 8: 3 MountingThe Protege Controller is
Page 9 and 10: +-4 Connections4.1 Protege SE Integ
Page 11 and 12: 4.5 AC PowerThe Protege Controller
Page 13 and 14: 4.7 Battery Charge Current SettingT
Page 15 and 16: ULULČIf an external power supply
Page 17 and 18: Warning: Power to the Protege Syste
Page 19 and 20: 5 Door Access ControlThe Controller
Page 21 and 22: 5.3 Door Contact ConnectionThe Cont
Page 23 and 24: The default settings are shown in t
Page 25 and 26: Each zone input can use a different
Page 27 and 28: 7 Programmable OutputsThe Controlle
Page 29 and 30: 8 Hardware Configuration8.1 Configu
Page 31 and 32: 9 LED IndicatorsThe Controller incl
Page 33 and 34: 10 Mechanical DiagramThe mechanical
Page 35 and 36: 12 System CapacitiesThe Protege Con
Page 37 and 38: 13 Technical SpecificationsThe foll
Page 39 and 40: 13.2 Current and Validation Example
Page 41 and 42: 13.4 Current and Validation (UL Ins
Page 43 and 44: 14 UL and ULC Installation Requirem
Page 45 and 46: The following options must be enabl
Page 47: In the ArmorIP Internet Monitoring
Page 51 and 52: In the event of unsuccessful commun
Page 53 and 54: 15 FCC Compliance StatementsFCC PAR
Page 55 and 56: 16 Industry Canada StatementThis cl
Page 57 and 58: 18 WarrantyIntegrated Control Techn
Page 60: 227-4045-001 : UL 06 March 2013

Installation Manual - ICT

Create successful ePaper yourself

Delete template?

Save as template?