Manual - Unvented Gas Log Heater or Vented Decorative Appliance

More documents

Recommendations

Info

CDVSC7 & CDV7 Series Gas FireplaceVENT PIPE CLEARANCESA Minimum of 3" Clearanceto the Top Is Required AlongHorizontal Length until FluePipe Penetrates OutsideWall.3"1"1" 1"A Minimum 1" Clearanceto Combustibles PermittedAll Around Flue at OutsideWallA Minimum of 3" Clearanceto the Top Is RequiredAlong Horizontal Lengthuntil Flue Pipe PenetratesOutside Wall.Venting installation3"1"1" 1"A Minimum 1"Clearance toCombustiblesPermitted AllAround Flue atOutside WallCDVR SeriesFP2289CDVT SeriesFP2288Figure 14 -Combustible Clearances for Vent PipeWARNINGFP2289Rear Vent: RV rear Horizontal vent sections of this ventsystem require a minimum of 3" clearancesto combustibles at the top of the flue and1" clearance at the sides and bottom untilthe flue penetrates the outside wall. Aminimum 1" clearance all around the flueis acceptable at this point of penetration.Vertical sections of this vent system requirea minimum of 1" clearance to combustibleson all sides of the pipe.WARNINGFP2288TV rear ventTop Vent: Horizontal sections of this ventsystem require a minimum of 3" clearancesto combustibles at the top of the flue and1" clearance at the sides and bottom untilthe flue penetrates the outside wall. Aminimum 1" clearance all around the flueis acceptable at this point of penetration. Ifvertical rise is 7 1 /2 feet or higher when topventing, the clearance to combustibles is1" on all sides of the horizontal run.Vertical sections of this vent system requirea minimum of 1" clearance to combustibleson all sides of the pipe.18 69D3011
Venting installationCDVSC7 & CDV7 Series Gas FireplaceRear Wall Vent ApplicationWhen installed as a rear vent unit this appliance may bevented directly to a termination located on the rear wallbehind the appliance.• Only MHSC venting components are approved to beused in these applications (Refer to ‘Venting Components’listed for different installation requirements).• The maximum horizontal distance between the rear ofthe appliance (or end of the transition elbow in a cornerapplication) and the outside face of the rear wall is20” (508 mm). Figure 14• Only one 45° elbow is allowed in these installations.• Minimum clearances between vent pipe and combustiblematerials are as follows:Top - 3” (76 mm)- except at outside wall 1" (25 mm)Sides - 1” (25 mm)Bottom - 1” (25 mm)9B\,”(244 mm)Min.Vent Opening for Combustible Walls9B\,”(244 mm) Min.Fireplace HearthFraming DetailOpening for Noncombustible Wall7Z\x”(190 mm)Figure 16 -Fireplace HearthLocate vent opening on wallFP2293Rear Vent Top View20”(508 mm)Max.Figure 15 -Rear Vent Application, No Elbows20”(508 mm)Max.FP1188REAR WALL FP1188 VENT INSTALLATION - TWISTLOCK PIPE rear wall installStep 1Locate and cut the vent opening in the wall.For combustible walls first frame in opening. Figure 16NOTE: When using flex vent, the opening will have to bemeasured according to the 1” (25 mm) rise in 24” (610mm) vertical run.Combustible Walls: Cut a 9B\,”H x 9B\,” W (244 x 244mm) hole through the exterior wall and frame as shown.Figure 16Noncombustible Walls: Hole opening should be 7Z\x”(191 mm) diameter.Step 2Secure firestop to the VO584-100 inside frame, center in the 9B\," x9B\," vent opening.Vent OpeningStep 3 2/99 djtMeasure the horizontal length requirement for the ventingincluding a 2” (51 mm) overlap, i.e. from the elbow to theoutside wall face plus 2” (51 mm). Figure 15Step 4Install the 4” (102 mm) vent to the appliance collar andsecure with 3 sheet metal screws. Install the 7” (178 mm)vent pipe to the appliance collar and secure with 3 sheetmetal screws. It is not necessary to seal this connection.If a 45° elbow is being used attach the elbow to the appliancein the same manner then attach the venting to theelbow.It is critical that there is no downward slopeaway from the appliance when connectingthe vent or elbow.Step 5Guide the venting through the vent hole as you place theappliance in its installed position. Guide the 4” (102 mm)and 7” (178 mm) collar of the vent termination into theouter ends of the venting. Do not force the termination. Ifthe vent pipes do not align with the termination, removeand realign the venting at the appliance flue collars. Figure17. Attach the termination to the wall as outlined in theinstruction sheet supplied with the termination.69D3011 19
Page 1 and 2: Installation and OperatingInstructi
Page 3 and 4: IMPORTANT SAFETY INFORMATIONINSTALL
Page 5 and 6: product featuresCDVSC7 & CDV7 Serie
Page 7 and 8: fireplace dimensions & FRAMINGCDVSC
Page 9 and 10: pRE-INSTALLATION INFORMATIONBefore
Page 11 and 12: CLEARANCESCDVSC7 & CDV7 Series Gas
Page 13 and 14: Venting INSTALLATION INFORMATIONCDV
Page 15 and 16: Venting INSTALLATION INFORMATIONCDV
Page 17: Venting INSTALLATION INFORMATIONHow
Page 21 and 22: Venting installationCDVSC7 & CDV7 S
Page 27 and 28: fireplace installationCDVSC7 & CDV7
Page 29 and 30: CHECK GAS PRESSURE & Electrical ins
Page 31 and 32: Electrical installationCDVSC7 & CDV
Page 33 and 34: millivolt OPERATING INSTRUCTIONSCDV
Page 35 and 36: electronic ignition OPERATING INSTR
Page 37 and 38: ELECTRICAL INSTALLATIONCDVSC7 & CDV
Page 39 and 40: OPTIONAL FAN BLOWER SYSTEMSCDVSC7 &
Page 41 and 42: OPERATING INSTRUCTIONS - SIGNATURE
Page 43 and 44: SIGNATURE COMMAND SYSTEM OPERATION
Page 45 and 46: SIGNATURE COMMAND SYSTEM OPERATION
Page 47 and 48: Log placementCDVSC7 & CDV7 Series G
Page 49 and 50: cleaning and maintenanceCDVSC7 & CD
Page 51 and 52: troubleshootingCDVSC7 & CDV7 Series
Page 53 and 54: troubleshootingCDVSC7 & CDV7 Series
Page 55 and 56: eplacement partsCDVSC7 & CDV7 Serie
Page 57 and 58: REPLACEMENT PARTSCDVSC7 & CDV7 Seri
Page 63 and 64: VENTING COMPONENTSHORIZONTAL VENTIN
Page 65 and 66: CDVSC7 & CDV7 Series Gas Fireplace6
Page 67 and 68: Limited lifetime warranty policyLif

Manual - Unvented Gas Log Heater or Vented Decorative Appliance

Create successful ePaper yourself

Delete template?

Save as template?