ITEM TOOLKIT

More documents

Recommendations

Info

S 5 Primary Repaired X Chapter 9 Markov 211 Furthermore, we assume that the system as a whole is unavailable when both the primary and standby components are failed. While in principle any number of states can be marked as unavailable, here we will limit it. 20. Right-click the state corresponding to the ‘both components failed’ state. A popup menu appears. 21. In the popup menu, select the State Parameters… option. A dialog box opens. 22. In the dialog box, check the ‘Unavailable State’ option, and click OK. 23. Ensure that in the editor pane, the state is indicated as being an unavailable state of the system by a small circle (A) appearing next to the state. A 24. Next, we introduce into the model the transitions representing the failures as well as repairs of the components. By inserting a transition originating in one state and leading to another, we model the possibility of an event-taking place that would bring the system from one state to another. In our simple model, we will insert eight transitions, as listed in the following Table. From To Description Rate Both Available Primary Failed Failure of primary component 0.001 Both Available Standby Failed Failure of standby component 0.0001 Primary Failed Both Available Repair of primary component 0.5 Primary Failed Both Failed Failure of standby while primary failed 0.001 Standby Failed Both Failed Failure of primary while standby failed 0.001 Both Failed Primary Repaired Repair of primary while standby still failed 0.5 Primary Repaired Both Available Repair of standby 0.5 Primary Repaired Both Failed Repair of primary while standby under repair 0.001 25. In the Markov toolbar, click the Arrow Link Button (B). This button is used to start the creation of new transitions. B 26. Left click on the Both Available state. A line originating from the state becomes visible as the mouse is moved around the Markov canvas. 27. Click on the Primary Failed state. An arrow appears between the two states. The arrow’s label indicates a rate of occurrence R of 0 (C). 28. Right-click on the label. A popup menu appears.
212 <strong>ITEM</strong> ToolKit Getting Started Guide 29. Select the ‘Transition Parameters’ option. A dialog appears. 30. In the field labeled ‘Transition’ (D), enter the value 0.001, corresponding to the rate of occurrence of this transition, and then click OK. The diagram indicates the updated rate of occurrence for the transition. C D 31. Repeat the process for the remaining seven transitions listed in the Table. 32. Now that both the states and transitions have been defined, the simple model is complete. 33. Along with states, it is possible to define state groups. You can create state groups in case you want to obtain the aggregated results, such as the combined state probability, for two or more states combined. A state group can contain
Page 2 and 3:
ITEM TOOLKIT ® TUTORIAL GETTING ST
Page 4 and 5:
Contents Contents i CONTENTS ......
Page 6 and 7:
Contents 1. CREATING A BILL OF MATE
Page 8 and 9:
Preface 1 Preface ITEM ToolKit is a
Page 10 and 11:
Chapter 1 Introducing ITEM ToolKit
Page 12 and 13:
Chapter 1 Introducing ITEM ToolKit
Page 14 and 15:
2. Hardware and Software Requiremen
Page 16 and 17:
Chapter 2 Installing ITEM ToolKit 9
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Activating the Software Chapter 2 I
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
• When the InstallShield Wizard C
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Network TCP/IP Connections Setup Ch
Page 46 and 47:
3. License Server Installation Chap
Page 48 and 49:
Installing the License Manager Chap
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
• When the InstallShield Wizard C
Page 56 and 57:
• Selecting Unlock Online opens t
Page 58 and 59:
Page 60 and 61:
Network File Share Connections Setu
Page 62 and 63:
Network TCP/IP Connections Setup Ch
Page 64 and 65:
4. Network Client Installation Chap
Page 66 and 67:
Installing the Software Chapter 2 I
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Activating the Software Chapter 2 I
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
5. View-Only Client Installation Ch
Page 82 and 83:
Installing the Software Chapter 2 I
Page 84 and 85:
Page 86 and 87:
• The Choose Network Destination
Page 88 and 89:
Page 90 and 91:
Chapter 3 ToolKit Basics 83 CHAPTER
Page 92 and 93:
Chapter 3 ToolKit Basics 85 The Sys
Page 94 and 95:
Chapter 3 ToolKit Basics 87 The Gri
Page 96 and 97:
Chapter 3 ToolKit Basics 89 The Cha
Page 98 and 99:
3. The ToolKit Menus Chapter 3 Tool
Page 100 and 101:
Add Menu Chapter 3 ToolKit Basics 9
Page 102 and 103:
Analysis Menu Chapter 3 ToolKit Bas
Page 104 and 105:
4. The ToolKit Toolbars Chapter 3 T
Page 106 and 107:
Chapter 4 Project Basics 99 CHAPTER
Page 108 and 109:
2. Opening a Project Chapter 4 Proj
Page 110 and 111:
4. Editing Project and System Prope
Page 112 and 113:
6. Closing a Project Chapter 4 Proj
Page 114 and 115:
Chapter 5 Predictions 107 CHAPTER 5
Page 116 and 117:
3. Creating a Prediction Project Ch
Page 118 and 119:
Chapter 5 Predictions 111 F E The t
Page 120 and 121:
Field Part Number Name Circuit Ref
Page 122 and 123:
Chapter 5 Predictions 115 D B A C E
Page 124 and 125:
Chapter 5 Predictions 117 Viewing R
Page 126 and 127:
Chapter 5 Predictions 119 4. Derati
Page 128 and 129:
2. Select the desired Derating stan
Page 130 and 131:
Chapter 5 Predictions 123 Creating
Page 132 and 133:
Chapter 5 Predictions 125 5. Predic
Page 134 and 135:
The Project Toolbar The Project Too
Page 136 and 137:
Chapter 5 Predictions 129 The NSWC
Page 138 and 139:
Chapter 6 FMECA 131 CHAPTER 6 FMECA
Page 140 and 141:
3. Creating a FMECA Project Chapter
Page 142 and 143:
Chapter 6 FMECA 135 A B C 2. Select
Page 144 and 145:
Chapter 6 FMECA 137 Field Mode - Re
Page 146 and 147:
Chapter 6 FMECA 139 2. Place the bl
Page 148 and 149:
Adding and Editing Components Chapt
Page 150 and 151:
Chapter 6 FMECA 143 Field Descripti
Page 152 and 153:
Defining FMECA Severity Chapter 6 F
Page 154 and 155:
3. Click the Mode + button to add a
Page 156 and 157:
Chapter 6 FMECA 149 D F G E H J 4.
Page 158 and 159:
Chapter 6 FMECA 151 5. If no errors
Page 160 and 161:
Chapter 6 FMECA 153 Use the SEV, OC
Page 162 and 163:
Chapter 6 FMECA 155 The FMECA Dialo
Page 164 and 165:
Chapter 7 RBD 157 CHAPTER 7 RBD A r
Page 166 and 167:
3. Creating an RBD Project Creating
Page 168 and 169: 5. Select the Add menu from the men
Page 170 and 171: Chapter 7 RBD 163 What is a Node? N
Page 172 and 173: Chapter 7 RBD 165 2. Select the fai
Page 174 and 175: When verifying RBD projects, ToolKi
Page 176 and 177: Understanding Analysis Results Chap
Page 178 and 179: The Default Toolbar Chapter 7 RBD 1
Page 180 and 181: Chapter 7 RBD 173 The Project Toolb
Page 182 and 183: Chapter 7 RBD 175 The Graph Toolbar
Page 184 and 185: Chapter 8 Fault Tree 177 CHAPTER 8
Page 186 and 187: Chapter 8 Fault Tree 179 Furthermor
Page 188 and 189: Chapter 8 Fault Tree 181 Field Desc
Page 190 and 191: Chapter 8 Fault Tree 183 Field Titl
Page 192 and 193: 6. Right Mouse Click on the new Gat
Page 194 and 195: Chapter 8 Fault Tree 187 • Dorman
Page 196 and 197: 2. If no errors are detected the fo
Page 200 and 201: Chapter 8 Fault Tree 193 3. Select
Page 202 and 203: Chapter 8 Fault Tree 195 4. Fault T
Page 204 and 205: The Project Toolbar The Project Too
Page 206 and 207: The Align Toolbar Chapter 8 Fault T
Page 208 and 209: Chapter 8 Fault Tree 201 The Canvas
Page 210 and 211: Chapter 9 Markov 203 CHAPTER 9 Mark
Page 212 and 213: 2. ITEM ToolKit & Markov Analysis C
Page 214 and 215: Chapter 9 Markov 207 Field Title Na
Page 216 and 217: Chapter 9 Markov 209 11. The next s
Page 220 and 221: Chapter 9 Markov 213 any number of
Page 224 and 225: Chapter 9 Markov 217 3. The Markov
Page 226 and 227: The Default Toolbar Chapter 9 Marko
Page 228 and 229: The Canvas Toolbar The Canvas Toolb
Page 230 and 231: The Graph Toolbar Chapter 9 Markov
Page 232 and 233: Chapter 10 MainTain 225 CHAPTER 10
Page 234 and 235: 3. Creating a Maintain Project Chap
Page 236 and 237: Chapter 10 MainTain 229 8. In the S
Page 238 and 239: Chapter 10 MainTain 231 Defining th
Page 240 and 241: Viewing Results To view the project
Page 242 and 243: Chapter 10 MainTain 235 4. Maintain
Page 244 and 245: The Project Toolbar The Project Too
Page 246 and 247: Chapter 11 SpareCost 239 CHAPTER 11
Page 248 and 249: Powerful Customizable Reports ToolK
Page 250 and 251: Chapter 11 SpareCost 243 The follow
Page 252 and 253: Chapter 11 SpareCost 245 F B D A C
Page 254 and 255: Chapter 11 SpareCost 247 23. Enter
Page 256 and 257: Understanding Analysis Results The
Page 258 and 259: Chapter 11 SpareCost 251 The Defaul
Page 260 and 261: Shortcut Keys: Chapter 11 SpareCost
Page 262 and 263: Chapter 12 Event Tree 255 CHAPTER 1
Page 264 and 265: Chapter 12 Event Tree 257 Once the
Page 266 and 267: Binary Decision Diagram (BDD): Chap
Page 268 and 269:
5. Enter your project information b
Page 270 and 271:
Chapter 12 Event Tree 263 11. Enter
Page 272 and 273:
5. Click on Event List and the Proj
Page 274 and 275:
2. Double Click on the Consequence
Page 276 and 277:
1. Click on the Event Tree Tab to o
Page 278 and 279:
Chapter 12 Event Tree 271 To Verify
Page 280 and 281:
Chapter 12 Event Tree 273 Importanc
Page 282 and 283:
Chapter 12 Event Tree 275 4. Event
Page 284 and 285:
The Project Toolbar The Project Too
Page 286 and 287:
Chapter 12 Event Tree 279 The Zoom
Page 288 and 289:
Chapter 13 Reports 281 CHAPTER 13 W
Page 290 and 291:
Chapter 13 Reports 283 Preview Tab
Page 292 and 293:
Chapter 13 Reports 285 This is an e
Page 294 and 295:
Chapter 13 Reports 287 Inserting a
Page 296 and 297:
Chapter 13 Reports 289 The Field Wi
Page 298 and 299:
Chapter 13 Reports 291 4. Problem S
Page 300 and 301:
Chapter 14 Import/Export 293 CHAPTE
Page 302 and 303:
Chapter 14 Import/Export 295 2. Imp
Page 304 and 305:
Chapter 14 Import/Export 297 8. Cli
Page 306 and 307:
Chapter 14 Import/Export 299 3. Exp
Page 308 and 309:
Chapter 14 Import/Export 301 Select
Page 310 and 311:
Chapter 15 Library Facilities 303 C
Page 312 and 313:
Chapter 15 Library Facilities 305 2
Page 314 and 315:
Chapter 15 Library Facilities 307 3
Page 316 and 317:
Chapter 16 Grid View Customization
Page 318 and 319:
Chapter 16 Grid View Customization
Page 320:
ITEM Software (USA) 34 Executive Pa
show all

ITEM TOOLKIT

Create successful ePaper yourself

Delete template?

Save as template?