Configuration Manual Synchronous Motors 1FT6 - Siemens ...

More documents

Recommendations

Info

Motor Description 1.6 Armature short-circuit braking 1) When utilized acc. to M0 (100 K) a series braking resistor must be used in order to prevent partial de-magnetization. When utilized according to M0 (60 K), the additional braking resistor is not required. 2) It is absolutely prohibited to short-circuit the winding when using smaller supplementary resistors than those specified. When braking from the rated speed, the resistors listed prevent partial de-magnetization of the rotor. 1FT6 synchronous motors 1-20 Configuration Manual, (PFT6), Edition 12.2004, 6SN1197-0AD12-0BP0
1.7 Cooling 1.7.1 Cooling types 1.7.2 Forced ventilation Motor Description 1.7 Cooling The different cooling types are defined in the Configuration Manual "General Section for Synchronous Motors".. Degree of protection IP54 (acc. to EN 60529). Degrees of protection IP64, IP65, IP67 and IP68 are not possible The hot discharged air may not be drawn-in again. Caution Forced ventilation cannot be used in the presence of flammable, corrosive, electrically conductive or explosive dust. Forced ventilation, SH 80 and SH 100 Air flow direction from NDE to DE. If the air flow direction is reversed, this reduces the torque yield by approx. 20 %. Mechanical changes to the motor with respect to non-ventilated versions: • The power connector is about 12 mm higher. • A sheet metal envelope is located over the motor frame from the non-drive end side. The axial fan is mounted in this sheet metal envelope. There is a cut-out in the sheet metal envelope at the connector positions. This means that the motor is only partially cooled by the air flow (three-sided ventilation). • The motor dimensions can be taken from the dimension drawings. Connection: Connector, Size 1, Order No.: 6FX2003–0CA10 Supply voltage: 1-ph. 230/260 V AC, 50/60 Hz Maximum current: 0.3 A Connector assignment for fan connections SH 80 and SH 100: 5 1 6 L1 4 2 N 1FT6 synchronous motors Configuration Manual, (PFT6), Edition 12.2004, 6SN1197-0AD12-0BP0 1-21
Page 1: ��
Page 4 and 5: Safety Guidelines This manual conta
Page 7 and 8: Foreword Information on the documen
Page 9 and 10: Danger and warning information Dang
Page 11 and 12: ESDS instructions Caution Standards
Page 13 and 14: Table of Contents Foreword ........
Page 15 and 16: Tables Table of Contents Table 1 Co
Page 17 and 18: Table of Contents Table 3-59 1FT613
Page 19 and 20: Motor Description 1 1.1 Features Ov
Page 21 and 22: 1.2 Technical features Table 1-1 Fe
Page 23 and 24: 1.4 Order designation Order designa
Page 25 and 26: Order designation for SH 132 water
Page 27 and 28: Motor Description 1.5 Technical dat
Page 29 and 30: Technical data 1FT6, rated speed 25
Page 31 and 32: Technical data 1FT6, rated speed 45
Page 33 and 34: 1.6 Armature short-circuit braking
Page 35 and 36: Table 1-5 Resistor braking for the
Page 37: Water-cooling Table 1-7 Resistor br
Page 41 and 42: 1.7.3 Water-cooling Cooling circuit
Page 43 and 44: Note Different anti-corrosion agent
Page 45 and 46: Cooling system Motor Description 1.
Page 47 and 48: Electrical Connections 2 2.1 Connec
Page 49 and 50: 2.2.3 Connection through a terminal
Page 51 and 52: 2.3 DRIVE-CLiQ The encoder system c
Page 53 and 54: 2.6 Rotating the connector at the m
Page 55 and 56: Technical Data and Speed-Torque Dia
Page 57 and 58: ��
Page 59 and 60: ��
Page 61 and 62: ��
Page 63 and 64: ��
Page 65 and 66: ��
Page 67 and 68: ��
Page 69 and 70: ��
Page 71 and 72: ��
Page 73 and 74: ��
Page 75 and 76: ��
Page 77 and 78: ��
Page 79 and 80: ��
Page 81 and 82: ��
Page 83 and 84: ��
Page 85 and 86: ��
Page 87 and 88: ��
Page 89 and 90:
��
Page 91 and 92:
��
Page 93 and 94:
��
Page 95 and 96:
��
Page 97 and 98:
��
Page 99 and 100:
��
Page 101 and 102:
��
Page 103 and 104:
��
Page 105 and 106:
��
Page 107 and 108:
��
Page 109 and 110:
��
Page 111 and 112:
��
Page 113 and 114:
��
Page 115 and 116:
��
Page 117 and 118:
��
Page 119 and 120:
��
Page 121 and 122:
��
Page 123 and 124:
��
Page 125 and 126:
��
Page 127 and 128:
��
Page 129 and 130:
��
Page 131 and 132:
��
Page 133 and 134:
��
Page 135 and 136:
��
Page 137 and 138:
��
Page 139 and 140:
��
Page 141 and 142:
��
Page 143 and 144:
��
Page 145 and 146:
��
Page 147 and 148:
��
Page 149 and 150:
��
Page 151 and 152:
��
Page 153 and 154:
��
Page 155 and 156:
��
Page 157 and 158:
��
Page 159 and 160:
��
Page 161 and 162:
��
Page 163 and 164:
��
Page 165 and 166:
��
Page 167 and 168:
��
Page 169 and 170:
��
Page 171 and 172:
��
Page 173 and 174:
��
Page 175 and 176:
��
Page 177 and 178:
��
Page 179 and 180:
��
Page 181 and 182:
��
Page 183 and 184:
Cantilever force 1FT6024, 1FT6028
Page 185 and 186:
Cantilever force 1FT6081, 1FT6082,
Page 187 and 188:
3.3 Axial forces Axial force stress
Page 189 and 190:
Motor Components (Options) 4.1 Ther
Page 191 and 192:
4.2 Encoders 4.2.1 Encoder overview
Page 193 and 194:
4.4 Motors without DRIVE-CLiQ 4.4.1
Page 195 and 196:
4.4.2 Absolute value encoders Funct
Page 197 and 198:
Cables Table 4-8 Prefabricated cabl
Page 199 and 200:
Connection assignment for 12-pin fl
Page 201 and 202:
4.6 Gearbox (option) 4.6.1 Introduc
Page 203 and 204:
Moments of inertia of the gearboxes
Page 205 and 206:
Table 4-14 1FT6 series with 1-stage
Page 207 and 208:
1) Values for cyclic/positioning du
Page 209 and 210:
Table 4-15 1FT6 series with 2-stage
Page 211 and 212:
Servomotor, non-ventilated Type Pla
Page 213 and 214:
Dimension Drawings 5.1 Introduction
Page 215 and 216:
Figure 5-2 1FT603⃞-⃞A⃞DQ Dime
Page 217 and 218:
Figure 5-4 1FT606⃞-⃞A⃞DQ Dime
Page 219 and 220:
Figure 5-6 1FT610⃞-⃞A⃞plug⃞
Page 221 and 222:
Figure 5-8 1FT616x-8Sx76-5xxx_DQ Di
Page 223 and 224:
Figure 5-10 1FT610⃞-⃞S⃞plug
Page 225 and 226:
5.2.3 Water-cooled 1FT6 motors Figu
Page 227 and 228:
Figure 5-14 1FT610⃞-⃞W⃞plug
Page 229 and 230:
Figure 5-16 1FT616x-8Wx76-5xxx_DQ D
Page 231 and 232:
2 3 4 5 6 7 8 1 A A 32 8 40 5.5 30
Page 233 and 234:
2 3 4 5 6 7 8 1 50 + 0,5 10 44 3.5
Page 235 and 236:
2 3 4 5 6 7 8 1 plug size 3 80 + 0.
Page 237 and 238:
Figure 5-24 1FT613⃞ non-ventilate
Page 239 and 240:
Figure 5-26 1FT616x-8Sx76-5xxx Dime
Page 241 and 242:
2 3 4 5 6 7 8 1 212 plug for fan po
Page 243 and 244:
Figure 5-30 1FT613⃞ force-ventila
Page 245 and 246:
Figure 5-32 1FT616⃞ force-ventila
Page 247 and 248:
2 3 4 5 6 7 8 plug size 3 1 water c
Page 249 and 250:
Figure 5-36 1FT610⃞ water cooling
Page 251 and 252:
Figure 5-38 1FT613⃞ water-cooled
Page 253 and 254:
Figure 5-40 1FT616⃞ water-cooled
Page 255 and 256:
2 3 4 5 6 7 8 1 1FT606. Q20 Q21 Q22
Page 257 and 258:
Appendix A.1 References General Doc
Page 259 and 260:
ASAL/ Configuration Manual, Inducti
Page 261 and 262:
Index A H Absolute value encoders,
Page 263:
To SIEMENS AG A&D MC BMS Postfach 3
show all

Configuration Manual Synchronous Motors 1FT6 - Siemens ...

Create successful ePaper yourself

Delete template?

Save as template?